OPAL/SMARAGD/RUBIN - Einhell-UNICORE sro

8
5
6
7
Page 21
Assembly of the crossmember
Important note: If you have purchased a
greenhouse with a single door then assemble the
crossmember as described in the steps 5/a and 5/b.
For a greenhouse with a double door, follow steps 5/c
and 5/d to assemble the crossmember.
Figs. 5/a + 5/b: Front wall with single door
Fig. 5/a: Make sure that the crossmember is
installed symmetrically.
Page 22
Figs. 5/c + 5/d: Front wall with double door
Fig. 5/c: Make sure that the crossmember is
installed symmetrically.
Page 23
Assembly of the roof strut
Page 24
Assembly of the door struts on a
greenhouse with a single door
If you have purchased a greenhouse with a double
door, skip step 7 and continue with step 8
„Assembly of the door struts on a greenhouse with a
double door“.
7/a: Install two bolts at one end of each of the two
door hinges, with one bolt around 60 cm and the
other around 5 cm from the edge. At the other end
attach one bolt around 30 cm and another around 5
cm from the edge.
Page 25
7/c: Slide the four pre-assembled hinge blades into
the guide rail of one of the door hinges. Make sure
that you screw down the hinge blades as shown in
Fig. 7/d.
Page 26
7/e: Two countersunk screws (item 3) are loosely
screwed into the two door strikers with M4 hexagon
nuts (item 4).
Page 28
7/h: Working from the outside, position the door
hinge between the floor profile and the crossmember
and secure it at the top using the pre-assembled
hexagon bolt. Make sure that the hinges face
towards the middle.
Important note: The door hinge with the hinges is
inserted on the left (viewed from the inside), the door
ABA_OSR_Teil1_Titel+GB.pmd 8
04.04.2006, 15:08
8
hinge with the striker plates on the right. Please refer
to the reference diagram on the next page.
Page 29
Reference diagram – internal view
Illustration: Left-hand profile: door hinge with hinges
Right-hand profile: door hinge with striker plates
Note:The cutouts on the floor profile and the
crossmember marked with an X in the reference
diagram stay free. Make sure that the door profile
with the hinges and the door profile with the striker
plates are inserted as shown in the reference diagram
(internal view!).
Page 30
Assembly of the door struts on a
greenhouse with a double door
If you have purchased a greenhouse with a single
door, skip step 8 and continue with step 9
„Assembly of the wind bracing and struts“.
8/a: Install three bolts at one end of each of the two
door hinges, with one bolt around 60 cm, one bolt
around 30 cm and the other around 5 cm from the
edge. At the other end attach one bolt around 30 cm
and another around 5 cm from the edge.
Page 31
8/c + 8/d: Slide four pre-assembled hinge blades into
the guide rail of one of the door hinges (see Fig. 8/c).
Three hinge blades are attached to the second door
hinge.Make sure that you screw down the hinge
blades as shown in Fig, 8/d, so that the door can be
subsequently inserted with the matching
counterparts.
Page 32
8/e: Make sure that the hinges face towards the
middle.
Important note: The door hinge with the four preassembled
hinges is inserted on the left (viewed
from the inside), the door hinge with the three hinges
on the right. Please refer to the reference diagram on
page 24 of the German assembly instructions.
Page 34
Reference diagram – internal view
Note: The cutouts on the floor profile and the
crossmember marked with an X in the reference
diagram stay free. Make sure that you insert the door
profiles with the hinges as shown in the reference
diagram (internal view!).