Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Betriebsanleitung <strong>BSC524</strong>-<strong>12V</strong> User’s manual <strong>BSC524</strong>-<strong>12V</strong><br />
5.2.2 Beschreibung der einzelnen<br />
Steuersteckerpins<br />
Description of the control connector<br />
pins<br />
5.2.2.1 GND (Masse, Ground), Pin 1<br />
Interne Beschaltung<br />
Internal Circuit<br />
GND (1)<br />
Gehäuse/housing<br />
5.2.2.2 AUX (Bordnetz, Auxiliary Supply),<br />
Pin 2<br />
Interne Beschaltung<br />
Internal Circuit<br />
AUX (2) 100uH 1.25A<br />
960nF<br />
30V<br />
6.8uF<br />
1MΩ<br />
15V<br />
Supply<br />
from<br />
AUX<br />
5µF<br />
Supply<br />
from HV<br />
Internal<br />
Supply<br />
• Direkte Verbindung zur Masse der Steuereinheit.<br />
• Nur kapazitiv mit dem Gehäuse verbunden.<br />
• Bei Verdrahtung von <strong>BSC524</strong>-<strong>12V</strong>-Steuersignalen<br />
mit anderen Fahrzeug-Komponenten (z.B. Fahrantrieb,<br />
Bordbatterie, Batteriemanagement, Brennstoffzelle)<br />
muss hier die Fahrzeug-Masse angeschlossen<br />
werden.<br />
11.2006-<strong>BSC524</strong>-<strong>12V</strong>_User Manual_V18b.doc 13 / 29<br />
HV<br />
5V<br />
• Das Gerät kann auch über diesen Anschluss vom<br />
Bordnetz versorgt werden. Wenn keine Hochspannung<br />
an den Leistungsanschlüssen anliegt, kann mit<br />
EN = „High“ über CAN oder RS232 mit dem Gerät<br />
kommuniziert werden. Folgende Funktionen sind bei<br />
ausschliesslicher Versorgung vom Bordnetz (Steuerstecker)<br />
sichergestellt:<br />
Senden und Empfangen von CAN-Informationen<br />
Kommunikation über RS232 (Monitor-<br />
Programm)<br />
Programmieren der Firmware<br />
Spannungs-, Strom und Temperaturmessung<br />
• Eingangstrom I_AUX bei <strong>12V</strong>-Bordnetzspannung:<br />
EN = „L“: 14uA<br />
EN = „H“: 305mA (keine HV-Spannung angelegt)<br />
• Direct connection to control unit ground .<br />
• Capacitive coupling to case only.<br />
• If <strong>BSC524</strong>-<strong>12V</strong> control signals are connected to<br />
other vehicle components (e.g. propulsion system,<br />
on-board battery, battery management system,<br />
fuel cell) the vehicle’s ground must be connected<br />
to this terminal.<br />
• The device can be supplied by the auxiliary supply<br />
as well. If no high voltage at the power interface is<br />
applied, communication over CAN or RS232 can<br />
be enabled by setting EN = “high”. If only auxiliary<br />
supply (control connector) is applied, following<br />
functions are available:<br />
Send and receive CAN-messages<br />
Communication via RS232 (monitor-program)<br />
Download of firmware<br />
Voltage and temperature measurement<br />
• Input current I_AUX at <strong>12V</strong>-auxiliary supply:<br />
EN = „L“: 14uA<br />
EN = „H“: 305mA (no HV-voltage applied)