sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
An den Aufnahmeanfang zurückwi<br />
ckel n. 0szi I 1 oskop an<br />
Messpunkt lffiffi anschliessen;<br />
i n Wj edergabe starten.<br />
Beim Abspielen sich Schritt<br />
merken, bei wel chem di e<br />
höchste Ampl i tude gemessen<br />
wurde.<br />
Tri mmer auf di esen Schri tt<br />
zurückstellen. Beim Aufnehmen<br />
C9 wi eder schri ttwei se geri ngf<br />
ügi g von d'iesem Punkt aus<br />
verdrehen. Durch mehrmal i ges<br />
Versuchen, di e best mö91 i che<br />
Posi ti on des Bi as-Regi ers<br />
best i mmen .<br />
Best mö91 i che Posi ti on<br />
bedeutet:<br />
- Maximal e<br />
- stei I ste<br />
M'i t den Pot . Metern R2 f ür<br />
7,5 ips, RB für l5 ips und<br />
Rl 0 für 30 i ps Si gnal di e<br />
Aufnahmepegel einstel I en.<br />
Vorgehen<br />
<strong>20</strong> Sek. Zei tcode aufnehmen.<br />
Zurück an Aufnahmeanfang.<br />
In lrl'iedergabe Spannung an<br />
Messpunkt MFM p'it 0szi 1 i oskop<br />
messen.<br />
Ampl i tude<br />
und<br />
Si gnal -Fl anken.<br />
D'ie Spannung sol I gieich<br />
gross sei n , wi e di ejeni ge<br />
ab lnl.iedergabeband. Unter<br />
Punkt 2 wurde di ese gemessen<br />
und notiert.<br />
Verschi edene Aufnahmen und<br />
l^/'iedergaben ausführen, bi s<br />
d'i ese s erre i c ht r,ui rd .<br />
Rewi nd the tape to the start<br />
of previ ous record. Connect<br />
osc'i I 1 oscope to test poi nt<br />
ffi@. Start transport i n<br />
pl ay.<br />
,Remember the<br />
step were<br />
the hi ghest ampl i tude occurs.<br />
Turn back the trimmer C9<br />
to that step where the<br />
hi ghest ampi i tude has been<br />
achi eved. For best adjustment<br />
a recordi ng wi thi n a I imi ted<br />
range of the trimmer around<br />
the poi nt wi th the hi ghest<br />
output voltage can be carried<br />
out agai n. Sel ect j n pl ay<br />
the best posi ti on aga'i n<br />
and turn the bi as trimmer<br />
to the respondi ng posi ti on.<br />
Repeat it until the best<br />
bi as setti ng has been ach'ieved.<br />
The cri teri as for the best<br />
setti ngs are a maximum ampf i -<br />
tude and a most step si ope<br />
of the signal.<br />
t,,li th the potenti ometer Rz<br />
for 7,5 ips, RB for l5 ips<br />
and Rl0 for 30 ips the recording<br />
level can be set.<br />
Proced ure<br />
Record <strong>20</strong> seconds of time<br />
code. Wind back to the beginni<br />
ng of tape. Measure wi th<br />
osci I 1 oscope the vo1 tage<br />
at test pojnt ffiH.<br />
The vo1 tage shoul d be the<br />
same as measured from the<br />
test tape and noteci<br />
on paragraph 2 of this description.<br />
Vari ous recordi ngs anc reproduct'ions<br />
shoul d be carri ed<br />
out unti I the requi red I evel<br />
'is achi eved.<br />
SI B4l84<br />
9of<strong>20</strong>