sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
sT[JDtrR 3.I.2 ,/L Tape Deck Controller GR 20 EL ... - Revoxsammler
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Beachten Si e auch, dass das<br />
Band ungefähr symmetri sch an<br />
der Kopfoberfl äche an1 i egt<br />
und nicht über eine Kante gezogen<br />
wird. (Siehe Bild Sektion 4/19<br />
unten .<br />
* Anmerkung<br />
Das SMPTE Ei ngangssi gnal für<br />
den Codekanal muss immer mindestens<br />
2 Vpp sei n, um Drop outs<br />
zu verhindern. Erfolgt 7 1/2 ips,<br />
ist ein Offset von I ms zulässig.<br />
Zwe j<br />
wi chti ge Kontrol I en f ijr<br />
verbe s sertes Ze'itcode I esen<br />
im Schnel lwickeln<br />
Prüfen, dass im Schnel lwi ckel n<br />
die Bandabhebebol zen so<br />
ei ngestel 1 t si nd, dass das<br />
Band ca. I mm von der Capstanachse<br />
entfernt wird.<br />
Ist das nicht der Fal l,<br />
muss der Liftermagnet entsprechend<br />
eingestei1t werden.<br />
(Siehe Manual Sektian 3/28).<br />
Bi tte beachten<br />
Es i st mö91 i ch, dass dadurch<br />
die im Manual beschriebene<br />
Ei nstel I vorschri ft<br />
mehr st'immt.<br />
ni cht<br />
(Beim Schnel lwi ckel n k ann<br />
das Band di e Andruckro.l I e<br />
berühren, wenn di ese von<br />
Hand bjs zum Anschlag gedrücki<br />
wi rd) .<br />
Check al so that the tape touches<br />
the headsurface about symmetricall<br />
and not rui ns across an edge<br />
of the head. (See picture section<br />
4/19 bel ow) .<br />
* Addi t'ional note<br />
To prevent drop-out i t 'is necessary<br />
that the SMPTE-i nput-Si gnal<br />
on the code track i s always<br />
at least 2 Vpp. By 7 1/2 ips<br />
recordi ng an offset of I ms i s<br />
allolved.<br />
Two important check to improve<br />
time code readi ng i n fast wi nd<br />
ttte<br />
t. Check that i n fast wi nd<br />
mode the I i fters move the<br />
tape just as far that a<br />
cl earance between capstanshaft<br />
and tape of approx. 1 mm<br />
ari ses.<br />
Is this not the case please<br />
adjust the I i ftersol enoi d<br />
to achi eve the above condi t'ion.<br />
(See Manual section 3/28).<br />
Pl ease note<br />
It is poss'ib1e, that the<br />
adj u stment t herefore not<br />
corresponds to the instructions<br />
in the Manual.<br />
(tn fast w'ind<br />
be poss'ibie<br />
touches the<br />
while you push<br />
by hand to its<br />
mode jt might<br />
that the tape<br />
pi nchrol 1 er,<br />
the pi nchrol I er<br />
stop posi ti on ) .<br />
SI B4l84 12 of <strong>20</strong>