Indoor Unit Outdoor Unit CS-E9NKUAW CS ... - Panasonic

More documents

Recommendations

Info

16.1.1 Relationship between the condition of the air conditioner and pressure and electric current � Carry out the measurements of pressure, electric current, and temperature fifteen minutes after an operation is started. 44
16.2 Breakdown Self Diagnosis Function 16.2.1 Self Diagnosis Function (Three Digits Alphanumeric Code) � Once error occurred during operation, the unit will stop its operation, and Timer LED blinks. � Although Timer LED goes off when power supply is turned off, if the unit is operated under a breakdown condition, the LED will ON again. � In operation after breakdown repair, the Timer LED will not blink. The last error code (abnormality) will be stored in IC memory. 16.2.2 To Make a Diagnosis 1 Timer LED starts to blink and the unit automatically stops the operation. 2 Press the CHECK button on the remote control continuously for 5 seconds. 3 “- -“ will be displayed on the remote control display. Note: Display only for “- -“ (No signal transmission, no receiving sound and no Power LED blinking) 4 Press the TIMER ▲ or ▼ button on the remote control. The code “H00” (no abnormality) will be displayed and signal will be transmit to the main unit. 5 Each press of the button (▲ or ▼) will increase error code number and transmit error code signal to the main unit. 6 When the latest abnormality code on the main unit and code transmitted from the remote control are matched, Power LED will light up for 30 seconds and a “beep” sound (continuously for 4 seconds) will be heard. If no codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds. 8 The LED will be off if the unit is turned off or the RESET button on the main unit is pressed. 16.2.3 To Display Memorized Error Code (Protective Operation) 1 Turn power on. 2 Press the CHECK button on the remote control 3 “- -“ will be displayed on the remote control display. Note: Display only for “- -“ (No signal transmission, no receiving sound and no Power LED blinking) 4 Press the TIMER ▲ or ▼ button on the remote control. The code “H00” (no abnormality) will be displayed and signal will be transmit to the main unit. 5 Each press of the button (▲ or ▼) will increase error code number and transmit error code signal to the main unit. 6 When the latest abnormality code on the main unit and code transmitted from the remote control are matched, Power LED will light up for 30 seconds and a “beep” sound (continuously for 4 seconds) will be heard. If no codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds. 8 The same diagnosis can be repeated by turning power on again. 16.2.4 To Clear Memorized Error Code after Repair (Protective Operation) 1 Turn power on (in standby condition). 2 Press the AUTO button for 5 seconds (a “beep” sound is heard) on the main unit to operate the unit at Forced Cooling Operation Mode. 3 Press the CHECK button on the remote control for about 1 second with a pointed object to transmit signal to main unit. A “beep” sound is heard, and the Error Code is cleared. 16.2.5 Temporary Operation (Depending On Breakdown Status) 1 Press the Auto OFF/ON button on the main unit (a “beep” sound is heard) to operate the unit. (Remote control is enable again). 2 The unit can be temporarily be used until repaired. Error Code Operation Temporary items H23 Cooling H27, H28 Cooling, Heating Emergency Operation with limited power 45
Page 1 and 2: Order No: PHAAM1111087C1 Indoor Uni
Page 3 and 4: 1. Safety Precautions � Read the
Page 5 and 6: 2. Specification Cooling Heating In
Page 7 and 8: DRY BULB WET BULB DRY BULB WET BULB
Page 9 and 10: 4. Location of Controls and Compone
Page 11 and 12: 5.2 Outdoor Unit 11
Page 13 and 14: 7. Block Diagram 13
Page 19 and 20: 10.1.2 Power Printed Circuit Board
Page 21 and 22: 11. Installation Instruction 11.1 S
Page 23 and 24: 11.2.3 Indoor Unit Installation 11.
Page 25 and 26: 11.2.5 Wiring Stripping and connect
Page 27 and 28: 11.3.2.3 Connecting the piping to o
Page 29 and 30: 12. Operation Control 12.1 Basic Fu
Page 31 and 32: [Heating] o According to indoor pip
Page 33 and 34: � Control contents o Fan speed au
Page 35 and 36: 13. Operation Control (For Multi Sp
Page 37 and 38: 14. Protection Control 14.1 Protect
Page 39 and 40: 14.2.2 Cooling Overload Control �
Page 41 and 42: 15. Servicing Mode 15.1 Auto Off/On
Page 43: 16. Troubleshooting Guide 16.1 Refr
Page 47 and 48: Note: “○” - Frequency measure
Page 49 and 50: 16.4.2 H12 (Indoor/Outdoor Capacity
Page 51 and 52: 16.4.4 H15 (Compressor Temperature
Page 53 and 54: 16.4.6 H19 (Indoor Fan Motor - DC M
Page 55 and 56: 16.4.8 H27 (Outdoor Air Temperature
Page 57 and 58: 16.4.10 H30 (Compressor Discharge T
Page 59 and 60: 16.4.12 H33 (Unspecified Voltage be
Page 61 and 62: 16.4.14 H37 (Outdoor Liquid Pipe Te
Page 63 and 64: 16.4.16 H98 (Indoor High Pressure P
Page 65 and 66: 16.4.18 F11 (Indoor Pipe Temperatur
Page 67 and 68: 16.4.20 F90 (Power Factor Correctio
Page 69 and 70: 16.4.22 F93 (Compressor Rotation Fa
Page 71 and 72: 16.4.24 F96 (IPM Overheating) Malfu
Page 73 and 74: 16.4.26 F98 (Input Over Current Det
Page 75 and 76: 17. Disassembly and Assembly Instru
Page 77: 17.1.1.3 To remove control board 17
Page 80 and 81: � Piping Length Characteristic Co
Page 82 and 83: � Piping Length Characteristic He
Page 84 and 85: � Piping Length Characteristic Co
Page 86 and 87: � Piping Length Characteristic He
Page 88 and 89: REF. NO. PART NAME & DESCRIPTION QT
Page 90: REF. NO. PART NAME & DESCRIPTION QT

Indoor Unit Outdoor Unit CS-E9NKUAW CS ... - Panasonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?