Panel Assortment For The Body Repair Man - bei PICHLER ...
Panel Assortment For The Body Repair Man - bei PICHLER ...
Panel Assortment For The Body Repair Man - bei PICHLER ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Body</strong> work set model K<br />
Nine replaceable plastic impact heads with firmly integrated metal<br />
threaded inserts<br />
- Slide hammer 1kg.<br />
- All parts interchangeable.<br />
- Can be used as a slide hammer and with the knurled handle as a<br />
pure beating tool.<br />
Particularly suitably for steel, aluminium bodies and painted<br />
surfaces. It is possible by filing or grinding to modify the plastic<br />
heads.<br />
<strong>Body</strong> work set model K12 pcs. in a case p/n 655 75 00<br />
<strong>Panel</strong> assortment for the body repair man<br />
This beautiful and high-quality set composed of three panel<br />
hammers with Hickory handles and four dolly’s is supplied in a<br />
plastic case. <strong>The</strong> perfect set for the craftsman who values the<br />
optimal relationship between price and quality.<br />
<strong>Panel</strong> set "HICKORY" 7 pcs p/n 955 09 00<br />
Dolly set F<br />
Special dolly set for the stretch and shrink-free treatment of bodies<br />
made from normal, high-strength, special thin steel sheets and<br />
aluminium. Employment e.g.: door sheets, wing flaring and direct<br />
panel beating.<br />
A rubber-covered solid steel core provides for a full surface support<br />
during the sheet metal working.<br />
Used with pick irons for the best way results for colourless damage<br />
repair.<br />
Hand fist set F 7 pcs. p/n 655 77 00<br />
Rubber dolly’s with steel core<br />
Even the smallest workshop is subject to new technologies. Here<br />
we offer dolly’s for aluminium bodies as well as for the treatment of<br />
high-strength, specially thin steel sheets in two versions. <strong>The</strong><br />
dolly’s have a steel core and are covered with rubber. <strong>The</strong><br />
advantages are: full surface support (more than with conventional<br />
steel dolly’s), can be used also for direct impact, arranges the<br />
sheet metal without stretch or shrink.<br />
Rubber truing blocks set 2 pcs with steel core p/n 955 22 20<br />
G 01
G 02<br />
Edge impact iron<br />
Ridge width 145 mm<br />
450 mm long.<br />
<strong>For</strong> professional panel beating of edges and flares in hard to reach<br />
areas. This tool permits repair without damage to the edges. With<br />
a 4 sided grip to check the tool position in cavities. <strong>The</strong> edge<br />
impact iron can be folded up like a pocket knife, thus one can<br />
reach nearly every corner with the slim anvil blade e.g. in doors, at<br />
the tail sheet metal inside or in quarter panels. Because of the<br />
mobile blade the impact is always flat on the outer skin.<br />
Edge impact iron p/n 655 14 00<br />
Torque - panel hammer<br />
1 side flexible-swivelling with spiral outline 42 mm Ø and 1 side<br />
smooth 31.5 mm Ø.<br />
<strong>For</strong> material thicknesses from 0,2 to 1.0 mm.<br />
Due to the particular design of the tightening yoke of the hammer<br />
the beating is converted into a rotating motion the fan-like surface<br />
of the hammer stretches the metal so evenly that neither the<br />
material condition nor material thickness are changed<br />
Torque - panel hammer p/n 655 05 90<br />
<strong>Panel</strong> work system model 3<br />
Slide hammer panel set<br />
Basic device with slide hammer 5 kg (thread M 18x1,5)<br />
p/n 614 87 90<br />
Double hook, mobile p/n 653 55 30<br />
Draw clamp on his own tightening p/n 653 62 00<br />
Finger hook (draw hook "F") p/n 653 63 00<br />
Reinforcement angle/pair (only with finger hook) p/n 653 64 00<br />
Slide hammer panel set model 3 p/n 653 60 00<br />
Pneumatic slide hammer<br />
Overall length 660 mm, slide weight 1800 g<br />
2 rubber suction plates: size 1 Ø 155 mm, size 2 Ø 120 mm<br />
<strong>For</strong> the extraction of dents from body surfaces. Using the<br />
operating valve on the end of the handle the pressure drop and<br />
pressure build-up are regulated. With a compressor air bleed port<br />
of 6-8 bar traction power of 100 kg can be achieved. <strong>The</strong><br />
aluminium grasp is equipped with hand guard and has auxiliary<br />
vents to ensure rapid air release.<br />
Pneumatic slide hammer p/n 655 20 00
Mini draw clamp<br />
<strong>Body</strong> work clamps quick and easy to install. <strong>For</strong> hard to reach<br />
places which have a small working surface.<br />
Mini draw clamp model 2<br />
32 x 60 x 50 mm<br />
<strong>For</strong> lateral 90° course, without dumps and rotating.<br />
Mini draw clamp model 2 p/n 652 32 60<br />
Special draw clamp<br />
<strong>The</strong>se specially formed clamps allow work in hard to reach places<br />
of all stretching applications for the body repair man. Apart from<br />
the useful design this tool has enormous strength at the jaws. We<br />
have two models available so that as well as a flat muzzle form it is<br />
also possible to grip 90° bent sheet metals and to stretch them.<br />
Both draw clamps are provided with a neck slot head, which makes<br />
pulling possible when used with a double draw hook or with a chain<br />
or slide hammer.<br />
Draw clamp with flat cheeks for sheet metals with flat profile<br />
Draw over neck slot head p/n 900 16 30<br />
Draw clamp with 90° cheeks for sheet metals with angular<br />
profile. Draw over neck slot head p/n 900 16 40<br />
Triangle drawing equipment<br />
Model I-M500 and model X-M200<br />
Special drawing equipment.<br />
Since the use of metal bodies on the automobile there have been<br />
many variations of draw clamps. <strong>The</strong> advantage of these devices is<br />
that they can be used on columns, hinges, in the shock strut<br />
cathedral in fact anywhere where it is possible to fasten with<br />
screws or pins.<br />
Triangle drawing equipment model X-M200 p/n 900 20 20<br />
Triangle drawing equipment model I-M500 p/n 900 20 21<br />
Triangle drawing equipment model X-M200 + I-M500<br />
p/n 900 20 25<br />
Pair of clamping latches in tongue form<br />
Additional equipment for the triangle hauling equipment<br />
<strong>The</strong> clamping jaws are used in connection with the triangle drawing<br />
equipment, corrugated for seizing round creases as e.g. within the<br />
door frame.<br />
Latch pair " tongue form " p/n 900 20 27<br />
G 03
G 04<br />
Draw hook thumb form<br />
This draw hook is a valuable and quick link to body work. Without<br />
the need to screw in this thumb hook can be inserted into a double<br />
draw hook and be used e.g. connected into the eye of a draw<br />
clamp. <strong>The</strong> downward facing tap prevents slippage of the hook.<br />
Dead weight 450 gram, maximum tensile load 3 tons.<br />
Draw hook thumb form in connection with double draw hook<br />
p/n 953 55 10<br />
Twist/pulling equipment longitudinal channel front<br />
<strong>For</strong> stretching and truing the front longitudinal channel and the<br />
preparation of part replacement.<br />
<strong>The</strong> screw on plate with an interchangeable pull ring (M20) can be<br />
used on the left and right side.<br />
<strong>The</strong> device is screwed onto the bumper attachment. <strong>The</strong> hauling<br />
equipment is fixed with additional clamping devices to prevent<br />
detachment.<br />
Type: Audi A3, VW Golf IV<br />
Twist/hauling equipment longitudinal channel front<br />
p/n 652 10 50<br />
Universal telescopic gauge<br />
This tool has extremely universal application possibilities due to<br />
the special shape and the offset clamping plates of the gap gauge.<br />
Because of this it is possible to close the hood or trunk lid with the<br />
gap gauge mounted. Also with non parallel running clamping<br />
edges the gap gauge can be used, as the clamping plates can<br />
also be tilted. Because of the strong construction it is possible,<br />
through pulling or pressing the mounted gap gauge to change the<br />
gap dimension before welding.<br />
Universal telescope gauge p/n 900 10 30<br />
Grip wrench set 16 pcs<br />
Wrenches with rubber-covered handles.<br />
Apart from the special composition for body work each wrench is<br />
equipped with comfortable skid-proof and cooling restraining<br />
rubber grips for comfortable work.<br />
Grip wrenches set 16 pcs with rubber-covered handles<br />
p/n 900 50 00
Pneumatic rivet removing drill set<br />
With replaceable inserts and drills<br />
To allow optimal drilling out of the very hard and variable diameter<br />
large rivets during the separation of sheet metals, this special<br />
pneumatic rivet removing drill set with 3 replaceable centring<br />
attachments and 2 different large " RIVET TWISTING BIT" drill<br />
inserts which are co-ordinated to commercially standard rivets.<br />
Pneumatic rivet removing drill set with replaceable<br />
attachments and drills p/n 825 05 45<br />
Spot welding drill<br />
Made from special steel. <strong>For</strong> the removal of spot welds in sheet<br />
metal work and body construction.<br />
Spot welding drill HSSE 8,0 mm Ø p/n 270 50 00<br />
Pneumatic axial grinder<br />
Connection: 1/4" internal thread<br />
Operating pressure: 6 bar<br />
Air consumption: 285 l/min.<br />
Air outlet: in front<br />
Number of revolutions: 23000 1/Min.<br />
Weight: 600 g<br />
Particularly for the use of hard metal milling cutters with 6 mm shank.<br />
Pneumatic axial grinder p/n 820 50 00<br />
Hard metal milling cutters<br />
One piece polished, for the machining of welding seams, point and<br />
MIG welds, hardened steel, casting etc. (for application in the<br />
pneumatic axial grinder) shank Ø 6 mm.<br />
Spherical shape 10 mm Ø p/n 670 01 00<br />
Spherical shape 12 mm Ø p/n 670 01 20<br />
Drip shape 10 x 16 mm p/n 670 21 00<br />
Flame shape 8 x 20 mm p/n 670 10 80<br />
Cylindrical shape 10 mm p/n 670 31 00<br />
Hard metal milling cutters set 5 pcs p/n 670 50 00<br />
Laser weld seam milling cutter<br />
With the laser welding seam milling cutter welding seams can be<br />
loosened during body work. Specific milling avoids material<br />
weakening and damage to the lacquer finish, this can not to be<br />
prevented when grinding welding seams. Misaligned laser welding<br />
seams can be followed with the help of the oval-formed base plate.<br />
<strong>The</strong> milling depth is adjusted with the help of a fine thread and a<br />
rubber locking mechanism which is infinitely variable; as a result a<br />
milling trough of the sheet metal behind it is prevented.<br />
Welding seam release tool for laser welded seams<br />
Laser weld seam milling cutter set with 2 spherical cutters and<br />
2 plates p/n 960 80 50<br />
G 05
G 06<br />
Door hinge adjuster model W<br />
Specially formed correcting heads, applicable to many different<br />
vehicles. Using specially hardened steel for high rigidity. Because<br />
they are screwed into the handle a simple replacement of the<br />
correcting heads is possible.<br />
Correcting heads:<br />
Size 1 Type: Audi 80 /100, <strong>For</strong>d Fiesta, DB 201&124, Opel,<br />
Renault R5<br />
Size 2 Type: Audi 80 /100, <strong>For</strong>d Fiesta, DB 201&124, Opel,<br />
Renault R5<br />
Size 3 Type: VW Passat<br />
Size 4 Type: Citroën AX /ZX, <strong>For</strong>d Escort / Sierra,<br />
Peugeot 205 / 405, Renault R5, VW Polo / Golf III<br />
Size 5 Type: Opel Corsa B bottom / Omega B top/bottom, doors<br />
front: Citroën Evasion, Fiat Ulysse, Peugeot 806<br />
Size 6 Type: Opel Corsa B bottom / Omega B top/bottom, doors<br />
front: Citroën Evasion, Fiat Ulysse, Peugeot 806<br />
Size 7 Type: Opel Corsa B top, VW-Passat, Peugeot, Fiat<br />
Size 8 Type: Opel Corsa B top, Audi A4, VW Passat 97 top<br />
Size 9 Type: <strong>For</strong>d Galaxy, Seat Alhambra, VW Sharan<br />
Size 10 Type: <strong>For</strong>d Galaxy, Seat Alhambra, VW Sharan<br />
Parts: Jaw opening Side<br />
Size 1 9 mm left p/n 654 28 01<br />
Size 2 9 mm right p/n 654 28 02<br />
Size 3 10 mm p/n 654 28 03<br />
Size 4 12 mm p/n 654 28 04<br />
Size 5 8 mm right p/n 654 26 63<br />
Size 6 8 mm left p/n 654 26 64<br />
Size 7 13 mm right p/n 654 26 61<br />
Size 8 13 mm left p/n 654 26 62<br />
Size 9 14 mm left p/n 654 28 08<br />
Size 10 14 mm right p/n 654 28 09<br />
Universal handle 400 mm long. p/n 654 28 20<br />
Set compositions:<br />
Set Type: Correcting heads<br />
No. I Audi, DB, Opel size 1 & 2 p/n 654 26 50<br />
No. II <strong>For</strong>d, Renault size 1, 2 & 4 p/n 654 27 00<br />
No. III Peugeot, Citroën size 4 p/n 654 27 10<br />
No. IV VW size 3, 4 p/n 654 27 50<br />
No. V Audi, VW size 1, 2, 3 & 4 p/n 654 28 00<br />
No. VI Opel Corsa B bottom / Omega B top/bottom size 5 & 6 p/n 654 26 65<br />
No. VII Opel Corsa B top, Audi A3/A4/A6, Passat size 7 & 8 p/n 654 26 60<br />
No. VIII <strong>For</strong>d Galaxy, Seat Alhambra, VW Sharan size 9 & 10 p/n 654 28 10<br />
All sets include a handle.<br />
Set complete 11 pcs size1 – size10 p/n 654 29 00
Hinge disassembly and assembly set<br />
Because of the laterally bent SW 12 ratchet handle it is easy to<br />
reach inaccessible door hinges. Also can be used on other<br />
disassembly and assembly work such as fenders, boot lids, hoods<br />
and similar body parts. <strong>The</strong> very short manufactured bits are held<br />
with a retaining ball surely and firmly in the ratchet head, a special<br />
spring prevents slipping through and allows safe working. <strong>The</strong> set<br />
contains bits 10,12,13 mm. with twelve-point , M8, M10, M12 in<br />
XZN, T40, T45 Torx as Inbus M7 and M8.<br />
Hinge disassembly and assembly set 12mm. drive<br />
with 10 different inserts p/n 954 45 60<br />
Hinge repair set<br />
<strong>For</strong> the repair of worn hinges and for replacing worn out hollow<br />
spring pins with new larger diameter pins. <strong>The</strong> 3 edged titaniumnitrated<br />
special drill does not cut at the front and is cylindrically<br />
stepped. This ensures an accurate guidance of the drill and round<br />
drilling out of worn, oval hinge holes.<br />
Type : Opel Astra, Omega, Vectra etc.<br />
Hollow spring pin impact thorn 175 mm p/n 654 24 60<br />
Special drill 3 edged, titanium-nitrated p/n 274 80 00<br />
Slotted straight pin set Ø 8, (24 pcs) p/n 654 24 55<br />
Hinge repair set in a plastic case p/n 654 24 50<br />
Lock out set<br />
Extensive tool set to open locked vehicles. Different operating tools<br />
made of round steel bar; flat steel strip and plastic make it possible<br />
to unlock doors using the operating knob, the door lock linkage or<br />
the interior door handle. With the three-part 170 cm long "Long<br />
Jim" door handles are operated through the car interior. <strong>The</strong> two<br />
plastic wedges allow the entry of the tools. <strong>For</strong> illumination a staff<br />
flashlight is included.<br />
Lock out tool set complete. 22 pcs p/n 657 70 00<br />
in an imitation leather bag<br />
Note: Store these door opener tools under lock and bold!<br />
Air spreading cushion<br />
150 X 150 mm<br />
<strong>For</strong> the careful raising and forcing delicate materials e.g. in the<br />
instrument panel, windows and while using of the lock out tools.<br />
<strong>The</strong> spread cushion is pushed between the door frame and the A<br />
pillar or between the side window and the door panel. By inflating<br />
the spread cushion a consistent gap is created without damage. In<br />
order to fix or extend the gap plastic wedges e.g. p/n. 6611055 can<br />
be inserted.<br />
Air spreading cushion p/n 957 76 50<br />
G 07
G 08<br />
Door upholstery release pliers<br />
Particularly slim “aggressive" muzzle form, slightly wedge-shaped.<br />
<strong>For</strong> damage-free removal of the clips on door linings and other<br />
vehicle linings.<br />
Door upholstery release pliers p/n 654 51 50<br />
Door upholstery release pliers model XL<br />
Extra large version of 654 51 50<br />
Predominantly for use with wide linings in the door and luggage<br />
compartment upholstery with lining plugs that have a large<br />
diameter e.g. in the Golf V this model is highly recommended.<br />
Door upholstery release pliers model XL p/n 654 51 60<br />
Release lever set universal<br />
<strong>For</strong> the careful release of door linings, trim, armature linings and<br />
tie-clips without damaging. From break-proof but soft plastic so<br />
ideally suited to sensitive materials.<br />
Release lever set universal 4 pcs p/n 654 51 20<br />
Hatch lining release lever<br />
500 mm long.<br />
<strong>For</strong> the disassembly of hatch linings with difficult to reach retaining<br />
springs. <strong>The</strong> release lever directly seizes the retaining tie-clip and<br />
prevents damage of the lining.<br />
Type: Audi A3, A6, A4 Avant, VW Golf IV and Passat Variant<br />
Hatch lining release lever p/n 654 51 40<br />
Combination assembly wedge model 1<br />
22 x 270 mm,<br />
Groove side 15° bent, opening Ø 7,5 mm<br />
Slim universally applicable assembly wedge made from wear<br />
resistant plastic with groove. <strong>For</strong> the release of trim, protective<br />
caps, operating knobs, window pit borders and door linings.<br />
Combination assembly wedge model 1 p/n 611 11 70<br />
Combination assembly wedge model 2<br />
215 mm x 26 mm, groove ca 7,5mm, bent 45°<br />
Made from wear resistant plastic. <strong>For</strong> the release of trim, window<br />
pit borders and door linings.<br />
Type : Universal, specially MB trim clips<br />
Combination assembly wedge model 2 p/n 961 15 00
Trim disassembly board<br />
350 x 180 x 16 mm.<br />
Specially formed assembly and disassembly board for trim.<br />
- Light shatter resistant plastic<br />
- Reciprocal chamfered induction bevel makes it possible to<br />
dismantle close lying trim<br />
- Broad low-cut grasp oval permits sensitive even lever off of long<br />
trim<br />
- Semicircular milled out back for pressing the trim in.<br />
Trim disassembly board p/n 655 50 00<br />
Star screwdriver<br />
200 mm long.<br />
<strong>For</strong> star screw heads with 5 slots, e.g. emblem (boot lid).<br />
Type : Saab, Seat, Volvo<br />
Star screwdriver p/n 501 20 00<br />
Fender key model 3<br />
T 30 x 300 mm.<br />
Particularly slim T-section key in special length. <strong>For</strong> the<br />
disassembly of the fender, without the disassembly of the door.<br />
<strong>The</strong> slot between the opened door and the A pillar does not permit<br />
thicker tools.<br />
Type : BMW E 38<br />
<strong>For</strong> the headlight disassembly<br />
Type : Audi A 6, Renault Laguna (headlight adjustment)<br />
Fender key model 3 p/n 654 62 00<br />
Wiper arm repair set<br />
<strong>For</strong> the repair of the rusted tight arm linkages<br />
Set consists of:<br />
Expressing fork for removing the safety moon rings.<br />
Special punch for deflecting extremely firm wiper axles.<br />
Wire brush for cleaning teeth at the wiper arm axle.<br />
T-grasp reamer for cleaning and finish-reaming of the locating<br />
hole. Package of snap rings (20 pcs) in “original size"<br />
Type : VW Golf 4, Audi A3, Seat, Skoda etc.<br />
Wiper arm repair set p/n 658 24 00<br />
in a plastic box<br />
Refilling packing of snap rings (20 pcs) p/n 658 24 01<br />
G 09
G 10<br />
Wiper arm repair set model II<br />
<strong>For</strong> the repair of rusted tight wiper arm linkages.<br />
Set consists of:<br />
Expressing fork - Removing the snap rings.<br />
Punch - Deflecting the wiper axles<br />
Wire brush - Cleaning teeth.<br />
T-grip reamer - Cleaning and finish-reaming the locating hole.<br />
Package of snap rings (20 pcs) in " original size"<br />
Type: VW Sharan, Seat Alhambra, <strong>For</strong>d Galaxy<br />
Wiper arm repair set model II p/n 658 25 000<br />
in a plastic box<br />
Refilling packing of snap rings size II (20 pcs) p/n 658 25 010<br />
Rear window washer repair set<br />
<strong>For</strong> repairing the rear window washer.<br />
With this tool the remainder of the broken off washer nozzle is<br />
drilled out of the windshield wiper axle and if necessary the broken<br />
brass tubing in the rear windshield wiper motor is repaired.<br />
By using the windshield wiper axle screw as a guide the milling<br />
cutter for removing the remaining nozzle or the drill<br />
for removing the remaining riser pipe is accurately positioned.<br />
<strong>The</strong> brass tubing is replaced by the enclosed plastic tubes..<br />
Type : VW, Audi e.g. Golf IV, Passat, Sharan and Audi A4<br />
<strong>For</strong>d Galaxy, Seat Alhambra<br />
Rear window washer repair set p/n 658 23 20<br />
Plastic tubes 5 pcs. p/n 658 23 25<br />
Plastic tubes 10 pcs p/n 658 23 30<br />
Claw hook universal<br />
Applicable with slide hammer<br />
Impact weight 5 kg or 8 kg<br />
This hook model with a internal thread of M18x1.5 is universally<br />
applicable with our two slide hammers of 5 kg or 8 kg impact<br />
weight. Generally for rough panel work on the body and in the<br />
frame area, as well as for the disassembly of knuckles, tie rod<br />
joints, articulated bearings of wishbones etc.<br />
Claw hook universal p/n 953 55 30<br />
Slide hammer complete 5kg p/n 614 87 90<br />
Slide hammer complete 8kg p/n 614 88 00
Wiper arm extractor.<br />
<strong>For</strong> problem-free and damage-free extraction of windshield wiper<br />
arms.<br />
P/n A B C D E F<br />
Spindle<br />
Ball /<br />
Hollow /<br />
Press. p.<br />
6582232 22 29/31 20,5 3 29/31 35 K<br />
6582235 10,5 26 41 4 29,4 35 H<br />
6582240 14,2 27/25 23,4/41 4 27 33 B<br />
6582245 11 26 42 3 29 35 B<br />
6582250 14 - 45-51 3-7 - 45 P<br />
6582255 23 49/36 13/27 6 49 57 -<br />
6582257 14,2 27/25 23,4/41 4 27 33 B<br />
6582260 21 24/27,5 10/21/34 4 27,5 34 B<br />
6582265 12 54 34,8 6 54 60 B<br />
6582270 26 34 29,4 3,7 34 42 B<br />
6582280 22 29/31 20,5 3 29/31 35 B<br />
6582285 10,5 37 27 3 40 47 B<br />
9582272 38,5 46 43,5 2,5 46 52 P<br />
9582812 37,5 43,5 45 4 43,5 52 H<br />
9582815 14,2 27/25 23,4/41 4 27 33 H<br />
9582820 23,5 29 27 4 30 37 B<br />
9582823 14. 38 27 3 40 47 B<br />
9582825 12 30 32 4 30 36,5 B<br />
6582260H 21 28 10/21/34 4 28 34 H<br />
Wiper arm extractor p/n 658 22 32*<br />
Type: e.g. Fiat Ulysse front,<br />
Peugeot 306, 406, 806 front<br />
Saab all models<br />
VW Golf IV, V front<br />
Wiper arm extractor p/n 658 22 35<br />
Type : e.g. MB M,ML class rear, combi. models rear<br />
Peugeot 306, 806 rear<br />
Wiper arm extractor p/n 658 22 40*<br />
Type : e.g. Opel Astra G Caravan till 7.99 rear<br />
Peugeot 206, 307 rear<br />
VW Golf III, Polo old rear<br />
Wiper arm extractor p/n 658 22 45*<br />
Type : e.g. Citroën C3, C5, Xsara Break, Coupé, Picasso rear<br />
Opel Astra G Caravan from 7.99, Zafira rear<br />
Peugeot 307 SW rear<br />
Renault Clio, Espace, Megane Scenic rear<br />
Wiper arm extractor p/n 658 22 50*<br />
Type : e.g. Audi A3 front<br />
BMW E32,34,36,38,39 rear<br />
<strong>For</strong>d Mondeo from 2000 front<br />
Wiper arm extractor p/n 658 22 55*<br />
Type : e.g. Chrysler Voyager rear<br />
Wiper arm extractor p/n 658 22 57*<br />
Type : e.g. Audi A4, A6 front<br />
<strong>For</strong>d Focus front<br />
Opel Vectra rear<br />
Renault Megane rear<br />
VW general new models front<br />
G 11
G 12<br />
Wiper arm extractor p/n 658 22 60H<br />
Type : e.g. Audi A4, A6 rear<br />
Opel Corsa rear<br />
Seat Alhambra rear<br />
VW Golf IV Passat Variant, Sharan<br />
new models rear<br />
Wiper arm extractor p/n 658 22 60<br />
Type : e.g. Citroën Xsara Break, Coupé front<br />
MB M class front<br />
VW Lupo, Bora, Polo rear<br />
Seat rear<br />
Skoda rear<br />
Wiper arm extractor p/n 658 22 65*<br />
Type : e.g. Renault Laguna Kombi from 2000, Megane Scenic<br />
from 2000 rear<br />
Wiper arm extractor p/n 658 22 70<br />
Type : e.g. Citroën C5 Break rear<br />
<strong>For</strong>d Galaxy new models front<br />
Porsche Cayenne front<br />
Seat Alhambra new models front<br />
VW Sharan new models, Touareg front<br />
Wiper arm extractor p/n 658 22 80<br />
Type : e.g. VW Golf V front<br />
Wiper arm extractor p/n 658 22 85*<br />
Type : e.g. Audi A4 from 2004 rear<br />
VW Golf V rear<br />
Wiper arm extractor p/n 658 22 72<br />
Type : e.g. Porsche Cayenne rear<br />
VW Touareg rear<br />
Wiper arm extractor p/n 958 28 12*<br />
Type : e.g. Audi A3, A4, A6, Audi 80 rear<br />
Wiper arm extractor p/n 958 28 15<br />
Type : e.g. Honda Civic from 2002 rear<br />
Wiper arm extractor p/n 958 28 20*<br />
Type : e.g. Citroën Xsara Picasso front<br />
<strong>For</strong>d Mondeo new Traveller front<br />
<strong>For</strong>d Mondeo new Limousine front<br />
Peugeot 206, 307, 307 SW<br />
Renault Espace ,Megane Scenic front<br />
Wiper arm extractor p/n 958 28 23<br />
Type : e.g. Renault Megane front<br />
Wiper arm extractor p/n 958 28 25<br />
Type : e.g. Citroën C5 from 2004, C5 Limousine rear<br />
Peugeot 407 rear<br />
* Wiper arm extractor set- 10 pcs p/n 958 28 00<br />
in a case
Kombi two arm extractor<br />
Wiper arm & battery pole extractor.<br />
Universal, handy two-arm extractor with cone extraction device.<br />
Special tool for the extraction of battery pole clamps or to be used<br />
as a universal wiper arm extractor.<br />
Battery pole and Uni wiper arm extractor p/n 940 33 50<br />
Rear wiper arm extractor UNI Renault<br />
Rear wiper arm extractor UNI set 6 pcs. With 2 extraction plates.<br />
Type : Renault all new models and universal.<br />
Rear wiper arm extractor Renault p/n 958 28 30<br />
Wiper arm extractor two armed<br />
Universally applicable two armed extractor, auto centring.<br />
Wiper arm extractor two armed p/n 103 99 50<br />
Wiper arm extractor<br />
Wiper arm extractor with lateral guidance.<br />
Pair of narrow arms for wiper arm extractor p/n 658 21 42<br />
Pair of wide arms for wiper arm extractor p/n 658 21 43<br />
Wiper arm extractor two armed with pair of wide arms<br />
p/n 658 21 41<br />
Wiper arm extractor four armed p/n 658 21 40<br />
Wiper arm extractor set.<br />
Universally applicable extractor set for the fast and damage-free<br />
disassembly of wiper arms. <strong>The</strong> wiper arm grip arms are used with<br />
a spindle.<br />
Bridge with spindle<br />
Wiper arm extractor universal four armed p/n 658 21 40<br />
7 wiper arm claws size 1 - size 7<br />
Wiper arm extractor set in a case p/n 958 29 50<br />
with 7 claws<br />
Wiper arm extractor set.<br />
Universally applicable extractor set for the fast and damage-free<br />
disassembly of wiper arms. <strong>The</strong> wiper arm claws are used<br />
alternatively depending on the wiper construction with a slide<br />
hammer or spindle.<br />
Type : Universal<br />
Bridge with spindle (S)<br />
Bridge with slide hammer (H)<br />
Wiper arm claw size 1 opening 21,0 mm<br />
Wiper arm claw size 2 opening 23,8 mm<br />
Wiper arm claw size 3 opening 15,5 mm<br />
Wiper arm claw size 4 opening 22,0 mm<br />
Wiper arm claw size 5 opening 28,0 mm<br />
Wiper arm claw size 6 opening 18,8 mm<br />
Wiper arm claw size 7 opening 15,0 mm<br />
Wiper arm extractor set in a case p/n 658 21 00<br />
with 7 claws<br />
G 13
G 14<br />
Windscreen separation knife model M<br />
Release and blade grip made from aluminium with replaceable<br />
blade. <strong>For</strong> the cutting out of bonded windscreens. Operation by<br />
one man! (<strong>For</strong> non-fusible adhesives.)<br />
Repl. blade angle blade long wide<br />
No. 1 standard 90° 20 mm 8,5 mm p/n 658 51 00<br />
No. 2 long 90° 36 mm 11,0 mm p/n 658 51 30<br />
No. 4 pointed 90° 23 mm 3-8 mm p/n 658 51 40<br />
Windscreen separation knife model M incl. stand. knife no.1<br />
p/n 658 50 00<br />
Windscreen separation knife model M set 5 pcs.<br />
p/n 658 51 50<br />
Windshield assembly equipment<br />
<strong>For</strong> the problem-free installation of nearly all non-bonded<br />
windshields and for drawing in the trim. <strong>The</strong> trim drawing in tool<br />
can be adapted to different trims by the use of 5 different inserts.<br />
Three further tools for installing and cleaning e.g. glass<br />
remainders are contained in the set.<br />
Contents:<br />
Handle with 6 m cord<br />
Trim drawing in tool with 5 inserts<br />
Trim cleaning tool, for removing of glass remainders<br />
Hook tool, curved<br />
Hook tool, straight<br />
Windshield assembly equipment 5 pcs. p/n 657 35 00<br />
in a plastic case<br />
Pass through awl disk disassembly<br />
280 mm lg.<br />
<strong>For</strong> puncturing the windscreen adhesive and for drawing in and<br />
drive through of the cutting wire during the disassembly of bonded<br />
windscreens.<br />
Passing through awl windscreens disassembly p/n 657 35 20<br />
Auto glass disassembly set<br />
<strong>The</strong> set contains as well as the classical hand cutting tools with<br />
square cutting wire, a separation knife, a passing through awl, a<br />
cutting knife for removing the remaining adhesive, a universal<br />
scraper and a clip tool<br />
Auto glass disassembly set 8 pcs p/n 957 00 00<br />
in a plastic case
Suction pad<br />
<strong>For</strong> body attachment and windscreen fixing<br />
Suction pad p/n 658 20 00<br />
Suction pad set model F<br />
Carrying capacity: 50 kg<br />
<strong>For</strong> lifting and transporting glass, for installation and removal of<br />
windscreens. Consists of two flexible lifting pads and a band.<br />
Vacuum lifting pad model F p/n 658 11 00<br />
Tightening strap p/n 658 75 00<br />
Vacuum lifting pad set model F, 2 pcs p/n 658 12 00<br />
Suction pad set 2 pcs "MINI"<br />
Universally applicable, an aid for the extraction of small dents and<br />
body damage or when mounting bonded windows, fix of trim,<br />
emblems or tuning accessories. This set with a carrying capacity of<br />
10-15 kg. per piece with a suction cup diameter of 57.0 mm is<br />
invaluable to any workshop.<br />
Vacuum lifting pad set small, Ø57,0mm suction power 10-15 kg.<br />
p/n 958 11 50<br />
Vacuum holder set<br />
Cup-Ø 60 mm,<br />
Steel retaining strap 280 mm long., rubber covered<br />
<strong>For</strong> fixing the side windows during work to the doors. <strong>The</strong> retaining<br />
strap is put over the door frame and fixed with the suction plates to<br />
the side window within the frame.<br />
Type : Universal<br />
Vacuum holder set 2 pcs p/n 658 11 50<br />
Pneumatic one hand disc grinder<br />
This unique hand disc grinder functions in connection with fibre<br />
corundum grinding disks. <strong>The</strong> newly conceived 5" hole supporting<br />
disk permits a favourable view of the worked surface and special<br />
air cooling of the work area. Further advantages are speed<br />
regulation, lightness and ergonomically formed handle for easy<br />
use.<br />
Pneumatic one hand disc grinder "BELLA-VISTA" for 5 holes<br />
fibre corundum grinding disks. p/n 804 38 00<br />
G 15
G 16<br />
Scraper<br />
Handy scraper with a replaceable blade. <strong>The</strong> blade can be moved<br />
by a slider with slots in the grasp. <strong>For</strong> removing stickers etc. from<br />
glass panels.<br />
Scraper p/n 311 15 00<br />
Spare blade p/n 311 11 00<br />
Plastic chisel and scraper set<br />
With 100 spare blades<br />
<strong>The</strong> plastic chisel is particularly well suited to removing the stuck<br />
on weights from aluminium rims or for the disassembly of<br />
adhesive trim and the like. <strong>The</strong> scraper is only good as long as it is<br />
sharp, therefore we include in this set 100 spare blades. Also the<br />
handle is flexible therefore easy to modify depending upon the<br />
required application.<br />
Plastic chisel and scraper set p/n 311 10 05<br />
Scraper and chisel set 4 pcs.<br />
This tool kit can be used either as scrapers or chisels. With solid<br />
continuous high-grade stainless steel blades (which can be<br />
reground). Ideally for removing plaques, stickers, adhesive<br />
detritus, seals etc., also as chisels for the separation of sheet<br />
metals and even spot welds.<br />
Scraper and chisel set 4 pcs. p/n 911 01 50<br />
Universal scraper and cutter set<br />
This universal set should be in every workshop. Whether you are<br />
cutting, scraping, separating or removing this set always has the<br />
suitable tool. With blades in widths 12mm, 16mm, 20mm straight,<br />
a 16mm diagonal blade for the scraper handle with a screwed<br />
holder, or a trapezoid blade for the cutter you are sure to have the<br />
correct tool for the job.<br />
Scraper set 27 pcs with replaceable blades p/n 911 05 00<br />
In a plastic box