a study on fine grinding process in jet mill - ePrints@USM

More documents

Recommendations

Info

ACKNOWLEDGEMENTS I wish to express my sincere gratitude towards Prof. Dr. Khairun Azizi Mohd Azizli for her supervision, undying encouragement, helpful suggestions and consistent assistance throughout this research work. The greatest debt of gratitude is also owed to Dr. Hashim Hussin and Dr. Syed Fuad Saiyid Hashim for their interest and support in this research work. Special thanks to Prof. Zainal Arifin Ahmad, Ir. Dr. Mior Termizi Mohd Yusof and Assoc. Prof. Dr. Azizan Aziz for their continuous encouragement and support during this research work. I’m thankful to Universiti Sains Malaysia, School of Materials and Mineral Resources Engineering, USM, and Institute of Postgraduate Studies, USM for giving the opportunity to conduct and complete this <strong>study</strong>. I’m thankful to everyone in School of Materials and Mineral Resources Engineering who had helped me in the completion of this thesis. I would like to thank my parents Mr. M. Palaniandy and late Madam A. Kamachyamah, brother, Soorianamtham and sisters, P. Yogamalar and P. Puganeshwary for their continuous support and encouragement until today. Lastly, a special thanks to my wife, Dr. Srimala and beloved daughter, Shemmalarvily for their support and love. ii
CONTENTS Page Number ACKNOWLEDGEMENT ii CONTENTS iii LIST OF TABLES viii LIST OF FIGURES x LIST OF ABBREVIATIONS xvii LIST OF SYMBOLS xviii LIST OF PUBLICATIONS xxii ABSTRACT xxiii ABSTRAK xxiv Chapter 1 INTRODUCTION 1.0 Introduction 1 1.1 Mechanochemical Effect Induced By Fine Grinding Process 1.1.1 Mechanochemical Effect Induced In Jet Mill 5 1.2 Problem Statement 6 1.3 Objective 8 1.4 Scope Of Work 8 Chapter 2 LITERATURE REVIEW 2.1 Introduction 10 2.2 Energy intensive grinding mills 13 2.3 Jet mill 15 2.4 Parameters affecting fine grinding process in jet mill 19 iii 3
Page 1: A STUDY ON ULTRA FINE GRINDING OF S
Page 5 and 6: Chapter 3 METHODOLOGY 3.1 Introduct
Page 7 and 8: REFERENCES 178 APPENDIX 1 : Volume
Page 9 and 10: Table 4.4 Table 4.5 Table 4.6 Table
Page 11 and 12: (●), 9000 rpm unsteady (○), 110
Page 13 and 14: Figure 3.4 Schematic diagram of gri
Page 15 and 16: Figure 4.24 Figure 4.25 Figure 4.26
Page 17 and 18: Rj rupture of joints CI cleavage Ch
Page 19 and 20: ψ span values di Kα βf βh βg D
Page 21 and 22: LIST OF PUBLICATION Samayamutthiria
Page 23 and 24: A Study on Ultra Fine Grinding of S
Page 25 and 26: 1.0 Introduction CHAPTER 1 The scop
Page 27 and 28: Although fine grinding will induce
Page 29 and 30: on the particle should be higher th
Page 31 and 32: eakage mechanism are controlled by
Page 33 and 34: operating parameters will be studie
Page 35 and 36: particles and it takes place simult
Page 37 and 38: Table 2.1: Key physical properties
Page 39 and 40: grinding soft materials such as sof
Page 41 and 42: Nozzle Nozzle Classifier Nozzle Mov
Page 43 and 44: Table 2.3: Application of jet mill
Page 45 and 46: (Berthiaux and Dodds, 1999; Tasirin
Page 47 and 48: The circularity (C) is a measure of

a study on fine grinding process in jet mill - ePrints@USM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?