a study on fine grinding process in jet mill - ePrints@USM

More documents

Recommendations

Info

ρg Gas density SEC specific energy consumption F feed rate C Circularity Deq A Area P Perimeter Equivelent diameter xx
LIST OF PUBLICATION Samayamutthirian Palaniandy, Khairun Azizi Mohd Azizli, Hashim Hussin and Syed Fuad Saiyid Hashim. (2007) Mechanochemistry of silica on Jet Mill. Journal of Materials Processing Technology. Accepted for publication. Samayamutthirian Palaniandy, Khairun Azizi Mohd Azizli, Hashim Hussin and Syed Fuad Saiyid Hashim. (2007). Effect of operational parameters on the breakage mechanism of silica in a jet mill. Minerals Engineering. Accepted for publication Samayamutthirian Palaniandy, Khairun Azizi Mohd Azizli, Mariatti Jaafar, Farrah Noor Ahmad, Hashim Hussin and Syed Fuad Saiyid Hashim. (2007) Effect of structural changes of silica filler on the coefficient of thermal expansion (CTE) of underfill encapsulant. Powder Technology, In Press, Accepted Manuscript. F.N. Ahmad, Mustapha Mariatti, Samayamutthirian Palaniandy and Khairun Azizi Mohd Azizli. (2007). Effect of particle shape of silica mineral on the properties of epoxy composites. Composites Science and Technology, In Press, Corrected Proof. Samayamutthirian Palaniandy, Syed Fuad Saiyid Hashim, Hashim Hussin and Khairun Azizi Mohd Azizli. (2004). Structural Defects during Fine grinding Process. Journal of Solid State Science and Technology Letters .11, 2 (Supplementary). Samayamutthirian Palaniandy, Khairun Azizi Mohd Azizli Syed Fuad Saiyid Hashim, and Hashim Hussin. Microstructure characterization of mechanically activated nanocrystallite quartz using XRD line broadening. (2006) Proceeding of International xxi
Page 1 and 2: A STUDY ON ULTRA FINE GRINDING OF S
Page 3 and 4: CONTENTS Page Number ACKNOWLEDGEMEN
Page 5 and 6: Chapter 3 METHODOLOGY 3.1 Introduct
Page 7 and 8: REFERENCES 178 APPENDIX 1 : Volume
Page 9 and 10: Table 4.4 Table 4.5 Table 4.6 Table
Page 11 and 12: (●), 9000 rpm unsteady (○), 110
Page 13 and 14: Figure 3.4 Schematic diagram of gri
Page 15 and 16: Figure 4.24 Figure 4.25 Figure 4.26
Page 17 and 18: Rj rupture of joints CI cleavage Ch
Page 19: ψ span values di Kα βf βh βg D
Page 23 and 24: A Study on Ultra Fine Grinding of S
Page 25 and 26: 1.0 Introduction CHAPTER 1 The scop
Page 27 and 28: Although fine grinding will induce
Page 29 and 30: on the particle should be higher th
Page 31 and 32: eakage mechanism are controlled by
Page 33 and 34: operating parameters will be studie
Page 35 and 36: particles and it takes place simult
Page 37 and 38: Table 2.1: Key physical properties
Page 39 and 40: grinding soft materials such as sof
Page 41 and 42: Nozzle Nozzle Classifier Nozzle Mov
Page 43 and 44: Table 2.3: Application of jet mill
Page 45 and 46: (Berthiaux and Dodds, 1999; Tasirin
Page 47 and 48: The circularity (C) is a measure of

a study on fine grinding process in jet mill - ePrints@USM

Create successful ePaper yourself

Delete template?

Save as template?