Spiral Retaining Rings & Wave Springs - Bearing Engineers, Inc.

Recommendations

Info

SELECTION GUIDE RINGS INTERCHANGE LISTING Smalley Retaining Rings are interchangeable with both inch and metric retaining ring grooves. Smalley offers FREE SAMPLES of all stock retaining rings to test in your application. Cross reference a standard stamped ring or snap ring to find the appropriate Smalley Retaining Ring to fit your application. METRIC EUROPEAN INDUSTRIAL SPIRAL MILITARY AEROSPACE AEROSPACE SPECIFICATION WALDES RETAINING SMALLEY ® EQUIVALENT MIL-DTL-27426 AS3219 MA 4035 DIN TRUARC EATON RING ANDERTON VH UR --- --- --- VS US --- --- --- WH RR /3 AS4299 --- AS3217 WS RS /1 AS4299 --- AS3218 Ordinary Stamped Retaining Ring Smalley ® Spiral Retaining Ring GROOVE INTERCHANGE ONLY Use a Smalley retaining ring to fit into the same groove of these stamped retaining rings. WHT RRT --- --- --- --- --- NAN --- --- WST RST --- --- --- --- --- XAN --- --- WHM RRN /4 AS4299 --- --- N5000 IN 3000 N1300 AS3215 5008 4000 WSM RSN /2 AS4299 --- --- 5100 EN 3100 N1400 AS3216 5108 4100 DNH --- --- --- --- DIN 472 --- --- --- D1300 DNS --- --- --- --- DIN 471 --- --- --- D1400 EH --- --- --- MA 4017 --- --- --- --- --- ES --- --- --- MA 4016 --- --- --- --- --- FH --- --- --- --- DIN 472 --- --- --- D1300 FS --- --- --- --- DIN 471 --- --- --- D1400 38 WWW.SMALLEY.COM
RUBBER BOOT A 2-Turn Spiral Retaining Ring clamps the rubber boot onto the groove making for a nearly perfect seal when the boot is filled with grease. The ring has been deburred so it will not tear into the rubber. RATCHET WRENCH This Single-Turn (it is actually 11 ⁄2 turns) External Retaining Ring retains the internal mechanical components of the ratchet wrench. The additional 1 ⁄2 turn provides that little extra strength needed to prevent the ring from dislodging when the wrench is dropped. RING APPLICATIONS PNEUMATIC FITTING An economical (without removal notches or offset) 2-Turn Spiral Retaining Ring creates an ID/OD lock, permitting the 360˚ rotation of the nut. This permanent assembly is commonly used to hold two components together. GEAR BRACKET The worm gear shaft is held in place and pre-loaded using a 2-Turn Smalley WaveRing. The WaveRing fits an internal groove and the waveform in the ring allows the gear/shaft to float axially as the gear rotates. CONDUIT CONNECTOR In this unique application, a Dished Retaining Ring was designed with sharp edges, to bite into the conduit it holds in place. The clamping force of the ring to the conduit (not shown) is achieved by screwing the nut. This decreases the ring’s diameter as it advances in a tapered bore. CALL SMALLEY AT 847.719.5900 39 RINGS
Page 1: Engineering and Parts Catalog Stock
Page 4 and 5: COMPANY PROFILE Founded in 1918 as
Page 6 and 7: RAW MATERIAL As we meet the increas
Page 8 and 9: FINISHED PARTS WAREHOUSE Smalley ma
Page 10 and 11: GENERAL INFO SMALLEY ENGINEERING &
Page 12 and 13: WAVE SPRING INTRODUCTION SPRINGS AL
Page 14 and 15: WAVE SPRING INTRODUCTION SPRINGS WA
Page 16 and 17: WAVE SPRING APPLICATIONS SPRINGS SL
Page 18 and 19: SSR SERIES STANDARD SECTION SPRINGS
Page 20 and 21: SSR-N SERIES NARROW SECTION WAVE SP
Page 22 and 23: SSB SERIES METRIC BEARING PRELOAD S
Page 24 and 25: CROSS REFERENCE GUIDE SSB BEARING T
Page 26 and 27: C/CS SERIES CREST-TO-CREST ® SPRIN
Page 32 and 33: SSRS SERIES CIRCULAR-GRAIN ® SHIMS
Page 34 and 35: RING INTRODUCTION RINGS ADVANTAGES
Page 36 and 37: SELECTION GUIDE RINGS RETAINING RIN
Page 40 and 41: RING APPLICATIONS RINGS BIKE LOCK T
Page 42 and 43: ASSEMBLY METHODS RINGS MANUAL INSTA
Page 44 and 45: VH SERIES LIGHT DUTY RINGS RINGS IN
Page 46 and 47: WH SERIES MEDIUM DUTY RINGS INTERNA
Page 48 and 49: WH SERIES MEDIUM DUTY RINGS INTERNA
Page 50 and 51: WHT SERIES MEDIUM HEAVY DUTY RINGS
Page 52 and 53: WHM SERIES HEAVY DUTY SERIES INTERN
Page 54 and 55: FHE SERIES SNAP RINGS INTERNAL RETA
Page 56 and 57: VHM SERIES LIGHT DUTY RINGS INTERNA
Page 58 and 59: EH SERIES METRIC AEROSPACE RINGS IN
Page 60 and 61: DNH SERIES DIN METRIC RINGS INTERNA
Page 62 and 63: FH SERIES METRIC SNAP RINGS INTERNA
Page 64 and 65: VS SERIES LIGHT DUTY RINGS EXTERNAL
Page 66 and 67: WS SERIES MEDIUM DUTY RINGS EXTERNA
Page 68 and 69: WS SERIES MEDIUM DUTY RINGS EXTERNA
Page 70 and 71: WST SERIES MEDIUM HEAVY DUTY RINGS
Page 72 and 73: WSM SERIES HEAVY DUTY RINGS EXTERNA
Page 74 and 75: FSE SERIES SNAP RINGS EXTERNAL RETA
Page 76 and 77: VSM SERIES LIGHT DUTY RINGS EXTERNA
Page 78 and 79: ES SERIES METRIC AEROSPACE RINGS EX
Page 80 and 81: DNS SERIES DIN METRIC RINGS EXTERNA
Page 82 and 83: FS SERIES METRIC SNAP RINGS EXTERNA
Page 84 and 85: ENGINEERING SPECIALS ARE STANDARD E
Page 86 and 87: MATERIALS TABLE ENGINEERING The tab
Page 88 and 89:
MATERIAL TYPES ENGINEERING SUPER AL
Page 90 and 91:
MATERIALS ENGINEERING SPECIFICATION
Page 92 and 93:
SPRING DESIGN ENGINEERING NOMENCLAT
Page 94 and 95:
SPRING DESIGN ENGINEERING STRESS OP
Page 96 and 97:
RING DESIGN ENGINEERING DESIGN ENGI
Page 98 and 99:
RING DESIGN ENGINEERING GROOVE GEOM
Page 100 and 101:
RING DESIGN MAXIMUM ALLOWABLE RPM E
Page 102 and 103:
SMALLEY ® ONLINE ENGINEERING www.S
Page 104 and 105:
SPRINGS CHECKLIST COPY THIS PAGE ·
Page 106 and 107:
HOW TO ORDER ENGINEERING SPECIFYING
Page 108 and 109:
GLOSSARY ENGINEERING Bore Diameter:
Page 110:
NOTES 110 WWW.SMALLEY.COM
show all

Spiral Retaining Rings & Wave Springs - Bearing Engineers, Inc.

Create successful ePaper yourself

Delete template?

Save as template?