ROTOGRAVURE PRINTING - heimann-hamm.de

More documents

Recommendations

Info

pre-press Galvanic | Color management | Engraving | Cylinder correction | Measuring devices CirCumferenCe meter d.mess Size I: Order No.: C01-0400 Size II: Order No.: C01-0410 Size III: Order No.: C01-0407 D.Mess – the next generation of the reliable digimess, already proven throughout the world wide industry, with increased measuring accuracy (+/- .00002 in.). D.Mess – the measuring system for those who need to measure diameter, circumference and roundness of printing cylinders, rollers etc. D.Mess measures with the utmost precision and reproducibility. The D.Mess fulfills the highest demands on measuring accuracy. D.Mess is very easy to use; even unskilled users can properly operate the instruments with full accuracy. The entire body of the D.Mess is made of distortion free reinforced cast aluminium. This construction guarantees longtime precision. A precise measuring probe, a microprocessor for the conversion of distance measurements, a temperature probe and a data printer are built into the instrument. The digital LED-display can be switched over to show either diameter or circumference. The measurement principle is a vertex measurement by means of a precision-angle-piece, with motorized, highly precisioned digital measuring probe and subsequent calculation to diameter and circumference. The external temperature influence to the object to be measured is compensated. Technical Data (subject to technical modifications) Measuring unit: The precision-angle-piece is made of special aluminium alloy. The supporting ledges are casehardened. Measuring range: Size I 2.75 – 13.60 inch Diameter (70 – 320 mm) Size II 9.84 – 19.68 inch Diameter (250 – 500 mm) Size III 19.68 – 26.37 inch Diameter (500 – 670 mm) Measuring accuracy: +/- .00002 in. (+/- 0,0005 mm) Accuracy of digital display: Diameter .00004 in. (0,001 mm) 6 digits Circumference .0004 in., (0,01 mm) 6 digits Temperature 0,1 °C 3 digits Measuring time: Without temperature compensation max. 4 sec. With temperature compensation max. 9 sec. Power supply: 6 rechargeable accumulators, size KR 27/50 (replaceable), recharging unit 220/110 V, 50/60 Hz, (overcharging is impossible). 34
dot-CheCk typ Wh343 (incl. objective 20x) typ Wh344 (incl. objective 20x and 40x) Order No. C01-0129 Order No. C01-0170 The world-wide known Dot-Check consists of a microscope with a high resolution CCD camera and a computing unit with monitor. The microscope is equipped with a special base so that it can be set up directly onto the cylinder. Two adjustable screws ensure an additional moving of the measuring position in directions x and y. Two measuring lines are administered in the image onscreen. The distance between these lines is indicated in µm. Since the measuring lines can be arranged both horizontally and vertically, it is very simple to measure the longitudinal and lateral diagonals of the cells. The depth can be specified by the adjustment of the surface to zero and the subsequent focus of the cell ground. The adjustment in the z direction is done by a motor. Technical Data (subject to technical modifications) Microscope: Type CSE Video-camera: CCD-camera Monitor: 10“ black-white Reproduction: onscreen in µm Illumination: high resolution-LED with automatic adjustment of light Maximum cable length between monitor and microscope: 6 meters Current Supply: 90 – 240 V alternating voltage (50 – 80 Hz) Maximum consumption: 50 W Enlargement and maximum measuring area in case of application of the following objectives: Tolerance in case of application of the objectives 20 fields (diagonal) or 40 fields (depth): 5 x 115-fields horizontally approx. 1400 µm and vertically 1000 µm 10 x 237-fields horizontally approx. 700 µm and vertically 500 µm 20 x 475-fields horizontally approx. 350 µm and vertically 250 µm 40 x 950-fields horizontally approx. 170 µm and vertically 150 µm ± 1 µm Options: • Videoprinter for printing of images and measuring values • Additional object lenses: 10- and 5- fields • Calibration plate • PCI plug cart inclusive of cable and software for storage of the images on one PC 35 BindEry – PostPrEss PrEss rooM PrE-PrEss
Page 1 and 2: ROTOGRAVURE PRINTING ACCESSOIRES &
Page 3 and 4: Press Room » Chemicals/Consumables
Page 5 and 6: Offi ce Hamm Alexandra Brandt Sales
Page 7 and 8: Also for your company, we will deve
Page 9 and 10: Especially in the micron range the
Page 11 and 12: If you are planning new investments
Page 13 and 14: Your contact to new markets Togethe
Page 15 and 16: GalvaniC Copper Bath Order No. Prod
Page 17 and 18: millinG off and turninG off Copper
Page 19 and 20: GrindinG and polishinG Order No. Pr
Page 21 and 22: platinized titanium anodes Order No
Page 23 and 24: IS PRESS MATCHER 7pt RIS PRESS MATC
Page 25 and 26: enGravinG tools A01-0001 ff We only
Page 27 and 28: minus CorreCtion Order No. Product
Page 29 and 30: pre-press Measuring devices Wall th
Page 31 and 32: hardness tester sd-h1 basic version
Page 33: CoatinG thiCkness tester minitest 3
Page 37 and 38: Description: CHECK-MASTER II is a c
Page 39 and 40: measuring head allows the direct 3D
Page 41 and 42: Technical data (subject to technica
Page 43 and 44: further produCts for rotation Order
Page 45 and 46: Ultra Doctor Blade This premium doc
Page 47 and 48: FUNCTIONS We supply SpectroDens in
Page 49 and 50: analytiC instrument Qfid-100hr Orde
Page 51 and 52: Features • Evaluation according t
Page 53 and 54: automatiC impression roller Cleanin
Page 55 and 56: heifareG varnish and ink control sy
Page 57 and 58: advantages Increased Web Speed Our
Page 59 and 60: t stroBe 3000 Order No.: C02-9004 S
Page 61 and 62: ChemiCals and ConsuminG materials f
Page 63 and 64: seCond hand maChines negotiation an

ROTOGRAVURE PRINTING - heimann-hamm.de

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?