Tube Bundle Connectivity - Emtelle Scandinavia A/S

Air Air Blown Fibre FttX Customers Fibre Products Products Tube Tube Bundle Sub-Duct Accessories Installation Equipment Equipment Tools Tools Training Emtelle Offi ces ces Terms & Conditions
Special Products
Direct Install metal free (DImf)
Pre-Installed Fibre Products
For further information on pre-cabled
duct please contact your local Emtelle
representative.
Examples of Cable/Duct Combinations
Minicable
Traditional
fi bre cable
TUBE BUNDLE - TIGHT PROTECTED MICRODUCT
It is essential that users of this product securely anchor the sheath and contents of the tube bundle to a fi xed point (eg manhole
side or duct mouth ) wherever the product emerges from a duct section. These duct sections should not be longer than 500m.
Refer to specifi cation MHT1772.
Both traditional fi bre optic and fi bre mini-cables are available as a pre-installed product. Lengths
of up to 4-10km are available dependent on the cable type and materials.
Emtelle can produce various combinations of a single fi bre cable in HDPE duct. This cable can be
removed at a later date and upgraded as required. This confi guration particularly favours fairly
long-distance fi bre-to-the-home (or building or MDU) deployment where neither the duct
nor fi bre cable are previously in place, and future installations or extensions may be called for.
These product combinations are designed for direct burial in suitably prepared ground.
Common typical features
■ Loose tube metal free constructions
■ Water blocked using gel fi lled tubes and dry
water swellable elements
■ Central strength element
■ Storage and operating temperature: -30°C
to +65°C
FIBRE CABLE DUCT OD & ID
count Typical diam 14/10 16/12 20/16 31/25 32/27 40/33
12f 4.2 ✔
24f 4.2 ✔
36f 5.8 ✔
48f 5.8 ✔
60f 5.8 ✔
72f 5.8 ✔
96f 7.3 ✔ ✔ ✔
144f 7.9 x ✔ ✔
192f 15.3 x x x ✔
288f 18.5 x x x x ✔
576f 22.8 x x x x x ✔
The tick boxes indicate the most economical pairings of fi bre cable and duct.
For pre-installed fi bre unit refer to page 17.
A simple sheathed bundle incorporating no metal, suitable for pulling into duct using moderate force.
When using Emtelle Direct Install Metal Free Products adequate provision must be made to take
account of all strain which may be caused by installation forces, practices and procedures, thermal
changes, heat reversion or any other reasonably foreseeable force applied to the product.
Product
Code
Description
Microduct Supply
Length
Minimum Product
Order weight
Quantity per metre gms
Type
Drum
Dimensions
(OD x W) mm
Weight
kg
Total weight
kg
Generic
Specifi cation
8321T 1DImf 5/3.5mm 4000m 4000m 47 G 1200 x 718 92 280 MHT1772
8374T 2DImf 5/3.5mm 4000m 4000m 71 MB5 750 x 1018 98 382 MHT1772
8353T 4DImf 5/3.5mm 4000m 4000m 109 1.4D 1400 x 1100 144 580 MHT1772
8008LT 7DImf 5/3.5mm 4000m 4000m 151 1.7D 1700 x 1140 237 841 MHT1772
8375T 12DImf 5/3.5mm 4000m 4000m 224 2.0D 2000 x 1140 345 1241 MHT1772
8367T 19DImf 5/3.5mm 4000m 4000m 310 2.35D 2350 x 1165 551 1791 MHT1772
60782 24DImf 5/3.5mm 2000m 4000m 410 2.0D 2000 x 1140 345 1165 MHT1772
Specifi cations (all types)
■ Available fi bre types: Singlemode ITU-T
G.652d, ITU-T G.655, ITU-T G.657A1, Multimode
A1 (IEC 60793-2-10)
■ Fibre and tube colours: normally EIA 598 or
EN187105
■ Cable tested to IEC 60794
38 I I N N N N O O V V A A T T I I O O N N A A N N D D F F L L E E X X I I B B I I L L I I T T Y
Y
38
At Emtelle we strive to improve our products every day and therefore strongly suggest that all new orders and specifications be confirmed by your Emtelle representative. The current specifications may be different
from those listed in our latest catalogues, which are limited by publication date. For the latest specifications please visit our website at www.emtelle.com or contact your Emtelle representative.