Workshop engine manual

More documents

Recommendations

Info

B ITEM VALVES Ø Sealing external diameter Exhaust.............................. Inlet.................................... Sealing face thickness...... Stem-guide clearance Exhaust.............................. Inlet.................................... Ø Guide internal diameter....... Valve stem Exhaust.............................. Inlet.................................... Valve spring Internal............................... External.............................. Valve-cam clearance Exhaust.............................. Inlet.................................... Engine +0,3 24,6 mm 0 +0,3 28,6 0 mm +0,2 1 mm -0,3 STANDARD 0,02 ÷ 0,04 mm......................... 0,01 ÷ 0.03 mm......................... +0 4,5 mm........................... +0,012 4,475 ± 0,005 mm..................... 4,485 ± 0,005 mm..................... 33,8 mm.................................... 37,9 mm.................................... 0,20 ÷ 0,29 0,15 ÷ 0,24 - 8 - WEAR LIMIT Coupling : 0,10 mm 4,55 mm 4,445 mm 4,455 mm 33,3 mm 37,4 mm 0,08 mm
ITEM CYLINDER AND PISTON Piston ovalization................... Piston-cylinder play................ Piston-pin play........................ Pin-foot connecting rod play..... Segment thickness 1 st ...................................... 2 nd ...................................... Oil scraper......................... Maximum segment-cylinder play CLUTCH 1 st ...................................... 2 nd ...................................... Scraper............................. Disk thickness........................ Springs................................... Engine STANDARD ................................................... 0,038 ÷ 0,067 mm 0,004 ÷ 0,012 mm 0,015 ÷ 0,032 mm -0,01 0,8 mm........................... -0,03 0 0,8 mm........................... -0,02 -0,03 1,5 mm........................... -0,08 0,2÷ 0,4 mm............................. 0,2 ÷ 0,4 mm............................. 0,2 ÷ 0,7 mm............................. 3 mm......................................... .................................................. - 9 - 0,015 mm 0,10 mm 0,03 mm 0,06 mm 0,75 mm 0,75 mm 1,38 mm 0,6 mm 0,6 mm 1 mm 2,8 mm 57,9 mm WEAR LIMIT B
Page 1 and 2: MVAGUSTA BRUTALE 910 S Workshop eng
Page 3 and 4: Workshop engine manual MVAGUSTA BRU
Page 5: Freni General Index GENERAL DESCRIP
Page 8 and 9: General description A SUMMARY HOW T
Page 10 and 11: A GLOSSARY AND SYMBOLS ATTENTION WA
Page 12 and 13: A General description RIGHT HAND AN
Page 14 and 15: A General description Brake fluid
Page 16 and 17: A General description OPERATIVE TEC
Page 18 and 19: B Engine SUMMARY TABLE OF CLAMPING
Page 20 and 21: B Engine CLAMPING TORQUES TABLE DES
Page 22 and 23: B Frequency Km (mi) Coupon Descript
Page 26 and 27: B GEAR SHIFT ITEM Gear fork-groove
Page 28 and 29: B Measuring compression in the cyli
Page 30 and 31: B Engine Verify the parameters of t
Page 32 and 33: B Engine Connect the depression pip
Page 34 and 35: B Engine Balance the pressures in t
Page 36 and 37: B CYLINDER HEAD Tightening torque O
Page 38 and 39: B Engine Remove the oil tube adduct
Page 40 and 41: B DISTRIBUTION CONTROL UNITS OIL Ap
Page 42 and 43: B Engine Remove the 12 tightening n
Page 44 and 45: B Engine Head assy assembly To exec
Page 46 and 47: B Engine Continue with the setting
Page 48 and 49: B Pin number 24 Pin number 25 Engin
Page 50 and 51: B Engine Do not tighten the stand s
Page 52 and 53: B Engine - 36 - 800094798
Page 54 and 55: B Substitution of the valve slot En
Page 56 and 57: B Guide valve installation Assemble
Page 58 and 59: B Assembling the valve. Engine Inse
Page 60 and 61: B CYLINDER AND PISTON GROUP OIL App
Page 62 and 63: B Cylinder revision Engine Check to
Page 64 and 65: B Engine Piston-pin connecting rod
Page 66 and 67: B CLUTCH 1 code 8000A2561 q.ty 7 2
Page 68 and 69: B Remove the disk pusher plate. Eng
Page 70 and 71: B Clutch overhauling Check the rod
Page 72 and 73: B Engine It is recommended that a n
Page 74 and 75:
B Engine Disassmbling gear group Re
Page 76 and 77:
B Primary and secondary shaft Check
Page 78 and 79:
B Installation To execute this oper
Page 80 and 81:
B ELECTRICAL COMPONENTS OIL Apply m
Page 82 and 83:
B OIL PUMP OIL Apply motor oil Engi
Page 84 and 85:
B WATER PUMP OIL Apply motor oil En
Page 86 and 87:
B Engine A)Heat the pump body (1) a
Page 88 and 89:
B STARTING OIL Apply motor oil Engi
Page 90 and 91:
B MOTOR SHAFT Engine Tightening tor
Page 92 and 93:
B BEDPLATE Engine Tightening torque
Page 94 and 95:
B Oil sump Engine Disassembling and
Page 96 and 97:
B Engine Disassembly Remove the oil
Page 98 and 99:
B Engine Revision Once you have dis
Page 100 and 101:
B Engine Verify with a thick meter
Page 102 and 103:
B LUBRICATION COMPONENTS: OIL TUBIN
Page 104 and 105:
B Engine When reassembling, clean t
Page 106 and 107:
B REPLACEMENT OF OIL FILTER Engine
Page 108 and 109:
B Engine Place the clamp lock at a
Page 110 and 111:
B Engine Reassembling Insert the su
Page 112:
Part No. 8A00A6440 Edition No. 1
show all

Workshop engine manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?