Ramsey MINI CK101 Weight Integrator - Hoferick Engineering GmbH

More documents

Recommendations

Info

2 IMPLEMENTATION ON THE <strong>MINI</strong>CK 101 2.1 The ‘PROFIBUS interface board’. Connection to the PROFIBUS will be done through a dedicated optional board ‘PROFIBUS interface board’ provided with the SPC3 controller. The SPC3 is an integrated circuit produced by SIEMENS, it handles the interface with the Master up to 12 Mbit/s. The PROFIBUS boards is provided by plug terminals 6 pin connector for RS485 connection. The board can be plugged into the instrument in the slot dedicated for the option. The software automatically will recognize it. 2.2 <strong>MINI</strong>CK 101 configuration and test. The slave address and the buffer dimensions should be defined on the instrument setup: ‘MAIN MENU 5 - PROFIB scroll’. Define here the address of the instrument in the PROFIBUS net. ──────────────────── - PROFIB SCROLL 1 - Password: SERVICE Address 1 ENTER ──────────────────── Default: 1 Min 1 Max 126 In the next two scroll the user can define independently the read and write buffer dimensions. This possibility is very useful since it allows to reduce the address space to allocate the instrument to the minimum needed. The dimension should be entered in number of words. This number includes also the header of the telegram (see Tab 2.1) that takes 4 words , so the minimum is 5 words. ──────────────────── - PROFIB SCROLL 2 - Password: SERVICE Read buffer dim 48 words ENTER ──────────────────── Default: 48 Min 5 Max 48 ──────────────────── 6 - 56
──────────────────── - PROFIB SCROLL 3 - Password: SERVICE Write buffer dim 48 words ENTER ──────────────────── Default: 48 Min 5 Max 48 ──────────────────── In the TEST SCROLL it is possible to check the actual status of the communication. ──────────────────── - TEST SCROLL 8 - Password: SERVICE Test communication B 19.2 kb Wait Prm ──────────────────── In the third line the baud rate and status are dynamically displayed. The status can be: WAIT PRM it is waiting for the PARAMETER message WAIT CFG it is waiting for the CONFIGURATION message DATA EXC it is in the DATA EXCHANGE phase , configuration and parametrization have been completed successfully. The baud rate is automatically detected by the instrument, if the displayed value changes continuously it means that there are problems on the line or the CPU is OFF. 7 - 56
Page 1 and 2: MINI CK101 Part No.: Pbus Ramsey MI
Page 3 and 4: INDEX About this manual ...........
Page 5: 1. PROFIBUS OVERVIEW 1.1 Introducti
Page 9 and 10: Write operations - Multiple registe
Page 11 and 12: same frequency the instrument updat
Page 13 and 14: 3 REGISTERS LIST 3.1 Description of
Page 15 and 16: Register Type Display (20) Display
Page 17 and 18: Language Register Type Time Format
Page 19 and 20: Register Type Weight Load Cell Zero
Page 21 and 22: Register Type Low rate delay Low ra
Page 23 and 24: Register Type Low Limit High Limit
Page 25 and 26: meanings, when the bit is 1 the ass
Page 27 and 28: O1.00 output 1 - mother board Comma
Page 29 and 30: 29 - 56
Page 31 and 32: 3.3.3 Display Data Units Code of th
Page 33 and 34: Speed Damping The Value in seconds
Page 35 and 36: Load Cell Sensitivity The value in
Page 37 and 38: Test Duration The value in engineer
Page 39 and 40: UNITS Feet Meters MAX 10000 300 MIN
Page 41 and 42: 3.3.8 Alarms Rate deviation opt. En
Page 43 and 44: 3.3.10 Profibus Settings Address Ad
Page 45 and 46: 45 - 56
Page 47 and 48: EXAMPLE 2 - READ HOLDING REGISTER T
Page 49 and 50: MULTIPLE REGISTERS QUERY RESPONSE M
Page 51 and 52: 1.101 (bin) This number can be repr
Page 53 and 54: APPENDIX B INSTRUMENT CONFIGURATION
Page 55 and 56: Follows the contents of the Ramsey

Ramsey MINI CK101 Weight Integrator - Hoferick Engineering GmbH

Create successful ePaper yourself

Delete template?

Save as template?