6724L3 1-a.book - SMC

More documents

Recommendations

Info

MAKING NETWORK CONNECTIONS 4-2 MDI-X port using straight-through cable. To connect between two switches/hubs that only have fixed MDI-X ports, the wiring crossover must be implemented in the cable - known as a crossover cable. The RJ-45 ports on the switch base unit support automatic MDI/MDI-X operation, which means that they automatically detect the wiring in the link and configure as MDI or MDI-X accordingly. So for these ports, you can use standard straight-through twisted-pair cables to connect to any other network device (PCs, servers, switches, hubs, or routers). However, note that auto-negotiation must be enabled on these ports for automatic wiring configuration to function properly. See Appendix B for further information on cabling. Connecting to PCs, Servers, Hubs and Switches Caution: Do not plug a phone jack connector into an RJ-45 port. This will damage the switch. Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. 1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector. Figure 4-1. Making Twisted-Pair Connections
TWISTED-PAIR DEVICES 2. If the device is a PC card and the switch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet. (See “Wiring Closet Connections” on the next page.) Otherwise, attach the other end to an available port on the switch. 3. Make sure each twisted pair cable does not exceed 100 meters (328 ft) in length. Note: When connected to a shared collision domain (such as a hub with multiple workstations), switch ports must be set to half-duplex mode. 4. As each connection is made, the Link LED (on the switch) corresponding to each port will light to indicate that the connection is valid. 4-3
Page 1: TigerSwitch 10/100 24-Port 10/100 M
Page 4 and 5: Information furnished by SMC Networ
Page 6 and 7: ii WARRANTIES EXCLUSIVE: IF AN SMC
Page 8 and 9: COMPLIANCES iv EC Conformance Decla
Page 10 and 11: COMPLIANCES vi Safety Compliance Wa
Page 12 and 13: COMPLIANCES viii
Page 14 and 15: TABLE OF CONTENTS 3 Installing the
Page 16 and 17: TABLE OF CONTENTS x
Page 18 and 19: ABOUT THE TIGERSWITCH 10/100 1-2 Me
Page 20 and 21: ABOUT THE TIGERSWITCH 10/100 Descri
Page 22 and 23: ABOUT THE TIGERSWITCH 10/100 System
Page 24 and 25: ABOUT THE TIGERSWITCH 10/100 1-8 Op
Page 26 and 27: ABOUT THE TIGERSWITCH 10/100 Featur
Page 28 and 29: ABOUT THE TIGERSWITCH 10/100 1-12
Page 30 and 31: NETWORK PLANNING Application Exampl
Page 32 and 33: NETWORK PLANNING Remote Connection
Page 34 and 35: NETWORK PLANNING Using Layer 3 Rout
Page 36 and 37: NETWORK PLANNING 10/100 Mbps Ethern
Page 38 and 39: NETWORK PLANNING 2-10
Page 40 and 41: INSTALLING THE SWITCH Equipment Che
Page 42 and 43: INSTALLING THE SWITCH 3-4 To rack-m
Page 44 and 45: INSTALLING THE SWITCH Installing an
Page 46 and 47: INSTALLING THE SWITCH Connecting to
Page 50 and 51: MAKING NETWORK CONNECTIONS Wiring C
Page 52 and 53: MAKING NETWORK CONNECTIONS 4-6 3. C
Page 54 and 55: TROUBLESHOOTING Power and Cooling P
Page 56 and 57: CABLES B-2 Maximum Fiber Optic Cabl
Page 58 and 59: CABLES Straight-Through Wiring B-4
Page 60 and 61: CABLES 1000BASE-T Cable Requirement
Page 62 and 63: CABLES B-8 The serial port’s conf
Page 64 and 65: SPECIFICATIONS C-2 LEDs System: PWR
Page 66 and 67: SPECIFICATIONS C-4 Weight 50 g (1.8
Page 68 and 69: SPECIFICATIONS C-6
Page 70 and 71: ORDERING INFORMATION D-2
Page 72 and 73: Auto-Negotiation Signalling method
Page 74 and 75: IEEE 802.3z Defines CSMA/CD access
Page 76 and 77: Glossary-6
Page 78 and 79: INDEX F features management 1-11 sw
Page 80: INDEX Index-4

6724L3 1-a.book - SMC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?