Download - Olivetti UK

More documents

Recommendations

Info

LE 05 Command Center LE 05 Command Center Safety Concept Requirements Measure The device's system settings have to be protected. In addition to system settings, any unauthorized device configuration should generally be prevented prevented. System settings must be protected from access via the Command Center. Only selected communication protocols must be used. Only certain interfaces must be used. Only certain PCs must be allowed to access the device. Access to the device / Command Center must only be granted to certain persons. Specific use of the device is granted to certain persons. The system settings are protected by a standard account (DeviceAdmin) (FS-6025: 2500 / 2500 and FS-6030: 3000 / 3000 This standard account should be changed as required to ensure long-term security. It is also practical to set up an additional account to ensure access if the "official“ password is lost or unknown (should be arranged with the customer). See page Authentication Access to the Command Center is protected by a standard password (admin00). This standard password should be changed as required to ensure long-term security. It is also practical to set up an additional account (see User Login) to ensure access if the "official" password is lost or unknown. See page Network safety See page Blocking the Interfaces See page IP-Filter Local Authentication Local authentication linked to a cost center.
Device safety LE 05 Command Center LE 05 Command Center Measure The start page is the starting point for various settings to increase the network's operational dependability. Recommendations Part of a security concept. Pre-conditions Administrative access to the Command Center. Notes On this start page, the relevant areas are briefly explained. By clicking on the underlined terms the desired setup area can be reached. Some settings require, where necessary, a network administrator's presence.
Page 1 and 2: B/W-MULTIFUNCTIONAL SYSTEM FOR PAPE
Page 3 and 4: Note for students This training man
Page 5 and 6: Options in detail DP Original size:
Page 7 and 8: Touch panel The touch panel is a ne
Page 9 and 10: IInstallation t ll ti (continuation
Page 11 and 12: Paper p feeder By inserting the cas
Page 13 and 14: Paper p feed unit 1. Main Motor 2.
Page 15 and 16: Duplex unit The Job Separator is us
Page 17 and 18: Developing unit Mono component syst
Page 19 and 20: Fuser unit The Fuser unit is only a
Page 21 and 22: Laser Scanner Unit Despite the spee
Page 23 and 24: Scanner unit The Image Scanner Unit
Page 25 and 26: Miscellaneous Below the Inner Tray
Page 27 and 28: Switch and sensor 1. Home position
Page 29 and 30: Cover disassembling Most of the cov
Page 31 and 32: Cover disassembling Remove the inne
Page 33 and 34: UU-425, 425 automatically calibrati
Page 35 and 36: System settings Activity Recommenda
Page 37 and 38: Maintenance mode Activity Enter the
Page 39 and 40: Maintenance mode LE 04 Maintenance
Page 41 and 42: Image adjustment procedure LE 04 Ma
Page 43 and 44: Paper jam detection Paper jam The c
Page 45 and 46: CContents: t t • Access • Desig
Page 47 and 48: Design of the Command Center The Co
Page 49: Helpful hints LE 05 LE Command 05 C
Page 53 and 54: Blocking the operation panel Action
Page 55 and 56: Network safety Measure Targeted act
Page 57 and 58: Authentication models No authentica
Page 59 and 60: Authentication models Network authe
Page 61 and 62: Authentication Action Specifying th
Page 63 and 64: Authentication Authentication, user
Page 65 and 66: Scan via network network, preparati
Page 67 and 68: SScanning, i Scan-to-Email S t E il
Page 69 and 70: SScanning, i Scan-to-SMB S t SMB Ac
Page 71 and 72: SScanning, i Send S d and d forward
Page 73 and 74: SSending di service i lists li t By
Page 75 and 76: Blank Page

Download - Olivetti UK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?