Download Entire Catalog - Cooper Industries

Open Box Support Mounting Assemblies
•• Example Part Number from page 22
BB716 - 10 4D _ _ - X _______ _ - 2 ______PKAV - X_______ _ - ________ _
1 2 3 4 5 6 7 8 9 8 10 8 11 12 6 7 8 9 8 10 8 11 12 6 7 8 9 8 10 8 11 12 6 7 8 9 8 10 8 11 12
Step 1 Step 2 Step 3 Step 2 Step 3 Step 2 Step 3 Step 2 Step 3
Position 1 Opening (if desired) Position 2 Opening (if desired) Position 3 Opening (if desired) Position Opening 4 (if desired)
(on BB824 only)
Step 1 - Basic Ruff-In
Plaster Ring Size
04 = 1 /4” Raise
08 = 1 /2” Raise
10 = 5 /8” Raise
12 = 3 /4” Raise
16 = 1” Raise
20 = 11 /4” Raise
24 = 11 2
/2” Raise
32 = 2” Raise
Box Style (see pg. 48)
4D = 4” Sq., 21 /8” Deep
436 = 4” Sq., 21 /8” Deep, 1” KO
4 = 4” Sq., 11 /2” Deep
432 = 4” Sq., 21 /8” Deep, 3 /4” KO
5D = 411 /16” Sq., 21 /8” Deep
560 = 411 /16” Sq., 21 /8” Deep, 1” KO
5 = 411 /16” Sq., 11 /2” Deep
554 = 411 /16” Sq., 21 /8” Deep, 3 /4” KO
431 = 4” Sq., 21 3
/8” Deep, Int. MC Connectors
4 Ground Wire
(Pre-installed devices require stranded wire)
Blank = Solid Ground Wire
A = Stranded Ground Wire
N = No Ground Wire
5 Firestop Pad (see pg.45)
Blank = No Pad
F = Pad Installed
Step 2 - Connectors
1 Stud Spacing
6 Position
BB716 = 16”
BB724 = 24”
1 = One Device and Box ∆
2 = Two Device and Box ∆
R = Round Plaster Ring and Box
6 = One Device and Box, No Ground Wire
7 = Two Device and Box, No Ground Wire
8 = Round Plaster Ring and Box,
No Ground Wire
X = No Attachments
∆ Only Options 1 and 2 can be used
with wiring devices.
If different box than called out in Step 1 is used
in any position, enter the designator for the box
after the character of the position.
For example ‘14D’ or ‘1432’.
7 Connector Top Left KO
Blank = No Attachment
L = Attachment Present
Connector Type (see pg. 49)
Blank = None
A = QLK50S ( 1 /2” single MC)
B = QLK50D ( 1 /2” double MC)
C = QLK75 ( 3 /4” single MC)
D = SSBC50 ( 1 /2” EMT Connector)
E = SSBC75 ( 3 8
/4” EMT Connector)
F = SSBC100 (1” EMT Connector)
9 Connector Top Middle KO
Blank = No Attachment
M = Attachment Present
10 Connector Top Right KO
Blank = No Attachment
R = Attachment Present
Basic Ruff-IN = 3-5 day lead-time for quantities of 1000 or less.
Ruff-IN with Wiring Devices = 10-15 day lead-time for quantities of 500 or less.
Non Stock Components = Call factory for lead-time.
Read safety/installation instruction sheets in packages before use. These products are designed for positioning only. No load rating.
23
Step 3 - Wiring Devices
Wire Configuration
P = Pigtails w/4 Hole Wago ®†
(all receptacles installed w/ground up)
R = Pigtails w/4 Hole Wago ®†
11
(all receptacles installed w/ground down)
M = Pigtails w/ Bare Wire Ends extending from
top KOs, Twist-On Wire Connectors Inside Box
(all receptacles installed w/ground up)
N = Pigtails w/ Bare Wire Ends extending from
top KOs, Twist-On Wire Connectors Inside Box
(all receptacles installed w/ground down)
Note: P, R, M and N configurations not available
if KO connectors are installed on the outlet box
12
Device Type or ArrowLink
Connector Options
Standard Device Type
(see pgs. 50-53)
3 Letter Designator For 1 Device
Two 3 Letter Designators For 2 Different Devices
One 3 Letter Designator For 2 Of The Same Device
ArrowLink Connector Options
(for more information see pgs. 54-55)
MCR = ArrowLink Connector, Receptacle/GFCI
MCS = ArrowLink Connector, Single-Pole Switch
† Marks shown are property of respective owners.
Ruff-IN