Owner's Manual - Roland

More documents

Recommendations

Info

[REVERB] 19. [REVERB] Knob You can switch between use of two types of reverb by changing the position of the knob. You can adjust the intensity of the eff ect by varying the knob position. The indicator lights up when reverb is on and goes out when the eff ect is off . You can also switch reverb on and off using an optional footswitch pedal. Knob Position Description SPRING PLATE This is modeled on spring reverb. It produces the distinctive reverberations of a spring. Turning the knob clockwise makes the eff ect progressively more intense. This is a plate reverb. This reverb features high-end sustain. Turning the knob clockwise makes the eff ect progressively more intense. POWER SQUEEZER (CUBE-40XL only) 20. [POWER SQUEEZER] Switch The switch lights in red when the power squeezer function is on and goes out when the power squeezer is off . Switching on the Power Squeezer function allows you to reduce the amp’s output to 2 watts. Switching this on allows you to produce a sound that preserves the same tone and balance at an output of 2 watts, for volume levels that are more suitable for the average home. * The Power Squeezer function aff ects only sounds input through the INPUT jack. It has no eff ect on sounds input via the AUX IN jack. POWER 21. [POWER] Switch This switches the power on and off . Switching the Power On and Off * Turn on power to your various devices in the order specifi ed. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. Make sure that all [VOLUME] knobs on the CUBE-40XL/CUBE- 80XL and all the connected devices are set to 0. 2. Turn on all the devices connected to the CUBE-40XL/CUBE- 80XL’s input jacks (INPUT jack and AUX IN jack). 3. Turn on the CUBE-40XL/CUBE-80XL. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 4. Adjust the volume levels for the devices. 5. Before switching off the power, lower the volume on all the connected devices and then TURN OFF the devices in the reverse order to which they were switched on. * If you need to turn off the power completely, fi rst turn off the POWER switch, then unplug the power cord from the power outlet. Refer to Power Supply (p. 3). 7 Nederlands Português Español Italiano Français Deutsch English
8 Rear Panel CUBE-40XL Recorder, etc. CUBE-80XL Headphones 6 1 2 3 TAP/STOP DELAY/REC/PLAY/DUB REVERB EFX SOLO CH SELECT External Speaker Foot switches Speaker Cable INPUT TAP/STOP DELAY/REC/PLAY/DUB REVERB EFX SOLO CH SELECT CD Player Digital Audio Player etc Recorder, etc. 1 2 3 4 6 7 5 8 Headphones Foot switches Mixer, etc. 8 RING TIP RING TIP RING TIP RING TIP RING TIP RING TIP Settings for momentary-type foot switches FS-6 FS-5U CD Player Digital Audio Player etc B A RING TIP * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
Page 1 and 2: Owner’s Manual Guitar Ampli er Ow
Page 3 and 4: 2 USING THE UNIT SAFELY About WARNI
Page 5 and 6: 1. INPUT Jack 4 Panel Descriptions
Page 7: 6 EQUALIZER 11. [BASS] Knob This ad
Page 11 and 12: 10 Using a Latch-type Foot Switch T
Page 13 and 14: 12 Using the SOLO Function You can
Page 15 and 16: 14 Using the LOOPER This function l
Page 17 and 18: 16 Sample Settings * For informatio
Page 19 and 20: 18 CUBE-40XL Block Diagram AUX IN I
Page 22 and 23: Information AFRICA EGYPT Al Fanny T
Page 24 and 25: This product complies with the requ
Page 26 and 27: WARNING: CAUTION CAUTION

Owner's Manual - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?