Indoor Unit Outdoor Unit CS-HE9NKE CS-HE12NKE CS ... - LMG

More documents

Recommendations

Info

11.2.3 Indoor Unit Installation 11.2.3.1 For the right rear piping 11.2.3.2 For the right and right bottom piping 11.2.3.3 For the embedded piping 26 (This can be used for left rear piping and bottom piping also.)
11.2.4 Connect the Cable to the Indoor Unit The power supply cord, indoor and outdoor unit connection cable can be connected without removing the front grille. 1 Install the indoor unit on the installing holder that mounted on the wall. 2 Open the front panel and grille door by loosening the screw. 3 Cable connection to the power supply through Isolating Devices (Disconnecting means). o Connect the approved polychloroprene sheathed power supply cord 3 × 1.5 mm 2 type designation 245 IEC 57 or heavier cord to the terminal board, and connect the other end of the cable to Isolating Devices (Disconnecting means). o Do not use joint power supply cord. Replace the wire if the existing wire (from concealed wiring, or otherwise) is too short. o In unavoidable case, joining of power supply cord between isolating devices and terminal board of air conditioner shall be done by using approved socket and plug with earth pin rated 15/16A . Wiring work to both socket and plug must follow to national wiring standard. 4 Bind all the power supply cord lead wire with tape and route the power supply cord via the left escapement. 5 Connection cable between indoor unit and outdoor unit shall be approved polychloroprene sheathed 4 × 1.5 mm 2 flexible cord, type designation 245 IEC 57 or heavier cord. Do not use joint connection cable. Replace the wire if the existing wire (from concealed wiring, or otherwise) is too short. 6 Bind all the indoor and outdoor connection cable with tape and route the connection cable via the right escapement. 27
Page 1 and 2: TABLE OF CONTENTS 1. Safety Precaut
Page 3 and 4: 1. Safety Precautions • Read the
Page 5 and 6: 2. Specification Cooling Heating Mo
Page 7 and 8: Drain Hose Indoor Heat Exchanger Ou
Page 9 and 10: Indoor Fan Outdoor Fan Speed Model
Page 11 and 12: 3. Features • Inverter Technology
Page 13 and 14: 5. Dimensions 5.1 Indoor Unit 13
Page 15 and 16: 6. Refrigeration Cycle Diagram 15
Page 17 and 18: 8. Wiring Connection Diagram 8.1 In
Page 19 and 20: 9. Electronic Circuit Diagram 9.1 I
Page 21 and 22: 10. Printed Circuit Board 10.1 Indo
Page 23 and 24: 10.2 Outdoor Unit 10.2.1 Main Print
Page 25: 11.2 Indoor Unit 11.2.1 How to Fix
Page 30 and 31: 11.3 Outdoor Unit 11.3.1 Install th
Page 32 and 33: 11.3.4 Connect the cable to the Out
Page 34 and 35: 12.1.5 Automatic Operation • This
Page 36 and 37: 12.4.1 Vertical Airflow Operation M
Page 38 and 39: C. Control contents a. Fan Speed ma
Page 40 and 41: 12.11 nanoe-G Operation • This op
Page 42 and 43: o nanoe-G breakdown error Judgment
Page 44 and 45: 12.12.1.2 Judge Sunlight Intensity
Page 46 and 47: 12.12.1.6 Sunlight Sensor Abnormali
Page 48 and 49: 13. Protection Control 13.1 Protect
Page 50 and 51: 13.2 Protection Control For Cooling
Page 52 and 53: 13.3.3 Overload Protection Control
Page 54 and 55: 4 REMOTE CONTROL RECEIVING SOUND OF
Page 56 and 57: 15.1.1 Relationship between the con
Page 58 and 59: 15.3 Error Code Table Diagnosis dis
Page 60 and 61: 15.4 Self-diagnosis Method 15.4.1 H
Page 62 and 63: 15.4.3 H14 (Indoor Intake Air Tempe
Page 64 and 65: 15.4.5 H16 (Outdoor Current Transfo
Page 66 and 67: 15.4.7 H23 (Indoor Pipe Temperature
Page 68 and 69: 15.4.9 H25 (e-ion Air Purifying Sys
Page 70 and 71: 15.4.11 H28 (Outdoor Pipe Temperatu
Page 72 and 73: 15.4.13 H32 (Outdoor Heat Exchanger
Page 74 and 75: 15.4.15 H34 (Outdoor Heat Sink Temp
Page 76 and 77:
15.4.17 H37 (Outdoor Liquid Pipe Te
Page 78 and 79:
15.4.19 H98 (Indoor High Pressure P
Page 80 and 81:
15.4.21 F11 (4-way valve Abnormalit
Page 82 and 83:
15.4.23 F90 (Power Factor Correctio
Page 84 and 85:
15.4.25 F93 (Compressor Rotation Fa
Page 86 and 87:
15.4.27 F96 (IPM Overheating) Malfu
Page 88 and 89:
15.4.29 F98 (Input Over Current Det
Page 90 and 91:
16. Disassembly and Assembly Instru
Page 92 and 93:
16.1.1.4 To remove control board Fi
Page 94 and 95:
Figure 10 94
Page 96 and 97:
17. Technical Data 17.1 Operation C
Page 98 and 99:
• Heating Characteristic [Conditi
Page 100 and 101:
17.1.2 CU-HE12NKE • Cooling Chara
Page 102 and 103:
• Heating Characteristic [Conditi
Page 104 and 105:
17.2 Sensible Capacity Chart • CU
Page 106 and 107:
REF. NO. PART NAME & DESCRIPTION QT
Page 108 and 109:
18.2 Outdoor Unit 31 55 8 7 52 53 5
Page 110:
REF. NO. PART NAME & DESCRIPTION QT
show all

Indoor Unit Outdoor Unit CS-HE9NKE CS-HE12NKE CS ... - LMG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?