- Page 1 and 2: SERVICE MANUAL Manufactured by Moti
- Page 3 and 4: CONTENTS: Page Ⅰ.The specificatio
- Page 5 and 6: 1.1 G-MAX 50 DIMENSION WEIGHT PERFO
- Page 7: 1.3 G-MAX 150 DIMENSION WEIGHT PERF
- Page 11 and 12: 2. 4T Engine (125/150 CC) NO Lockin
- Page 13 and 14: (3) Lubrication instruction A. 2T E
- Page 15 and 16: D.Wheel bearing Final transmission
- Page 17 and 18: (5)Trouble shooting: 1.difficult st
- Page 19 and 20: For 4T engine only: Oil level is no
- Page 21 and 22: 4.Engine running unsmoothly (high s
- Page 23 and 24: 6.Handlebar steering astrayed when
- Page 25 and 26: 10.Fuel indication malfunction (a)w
- Page 27 and 28: 11.The starting motor abnormal (a)S
- Page 29 and 30: 12.No sparking Check and adjust Tro
- Page 31 and 32: 3. Checking and Adjustment: (1)Regu
- Page 33 and 34: wheel Rear Damper Transmission Elec
- Page 35 and 36: Lamp system Horn, signal Lamp, refl
- Page 37 and 38: (3)Cleaning air cleaner 1.Remove ai
- Page 39 and 40: (6)Compression pressure measurement
- Page 41 and 42: (9) Idle adjustment: Note: adjust i
- Page 43 and 44: 4.1 Plastic part dismantle Overview
- Page 45 and 46: Loosen 3(LH) & 3(RH) tapping screws
- Page 47 and 48: Loosen 2 bolts of rear luggage comp
- Page 49 and 50: Dismantle 1 tapping screw in the fr
- Page 51 and 52: (1) Lubrication system and oil pump
- Page 53 and 54: 5.Assemble the oil pump. a. Assembl
- Page 55 and 56: (4)Drive pulley, starter & clutch A
- Page 57 and 58: 3.Remove the fixing nut of the clut
- Page 59 and 60:
9.To assemble the driving pulley, p
- Page 61 and 62:
D. Starter dismantling 1.Dismantle
- Page 63 and 64:
c. Check driven spring free length:
- Page 65 and 66:
D. cylinder head, cylinder, and pis
- Page 67 and 68:
9.Remove the Cylinder and the gaske
- Page 69 and 70:
5.Remove the flywheel. 6.Remove the
- Page 71 and 72:
3.Remove the 6 bolt in gear box cov
- Page 73 and 74:
E. Check for the flatness of cylind
- Page 75 and 76:
4.Piston outer diameter measurement
- Page 77 and 78:
8.Check connecting rod small end (1
- Page 79 and 80:
B. Troubleshooting. Engine noise: 1
- Page 81 and 82:
4.Remove the carburetor. 5.Remove t
- Page 83 and 84:
E. Check the crankshaft: 1.measure
- Page 85 and 86:
(9)Carburetor, Reed Valve A: Carbur
- Page 87 and 88:
C. Dismantling carburetor 1.Remove
- Page 89 and 90:
4. G-MAX 125/150 engine Dismantling
- Page 91 and 92:
Oil Pump Dismantling 1.Remove the r
- Page 93 and 94:
Measurement data Oil pump Troublesh
- Page 95 and 96:
(1) Drive pulley, starter clutch. d
- Page 97 and 98:
(C)Driving Pulley 1.Take off the sc
- Page 99 and 100:
5.To assemble the driving pulley, r
- Page 101 and 102:
D.Starter dismantle 1.Dismantle lef
- Page 103 and 104:
c.Check driving spring free length.
- Page 105 and 106:
A.Troubleshooting. If the cylinder
- Page 107 and 108:
Check cam shaft Check the convex su
- Page 109 and 110:
(6)Cylinder and piston A.Trouble sh
- Page 111 and 112:
D.Dismantling a.Dismantling Cylinde
- Page 113 and 114:
E.Installing Cylinder and piston a.
- Page 115 and 116:
Dismantling AC generator 1. Dismant
- Page 117 and 118:
(8)Final transmission mechanism A.
- Page 119 and 120:
3.Remove the final reduction gear A
- Page 121 and 122:
(9)Crankcase, Crankshaft: A. Disass
- Page 123 and 124:
C.Data Clearance of connecting rod
- Page 125 and 126:
(10)Carburetor: A.Troubleshooting.
- Page 127 and 128:
Too much fuel in the engine 1.Air c
- Page 129 and 130:
(C)The float nozzle 1.Dismantling R
- Page 131 and 132:
C. Change the speedometer cable: 1.
- Page 133 and 134:
(E)Front wheel 1.Remove the locking
- Page 135 and 136:
(F)Front brake 1. Disassembling and
- Page 137 and 138:
5.Disassembling and assembling the
- Page 139 and 140:
C. Disassembling and assembling the
- Page 141:
F. Rear absorber 1. Check the locki
- Page 144 and 145:
D. Oil tank disassembling diagram:
- Page 146 and 147:
(1)Troubleshooting: A. Recharge sys
- Page 148 and 149:
2.Recharge Connection procedure: co
- Page 150 and 151:
(3)Recharge system: A. Recharge sys
- Page 152 and 153:
2.Check A.C. Generator a. Open the
- Page 154 and 155:
(5)The starting system: 1.The wirin
- Page 156 and 157:
Wiring diagram for M2-50 46