THE GOLDMUND GOLDCUBE
THE GOLDMUND GOLDCUBE
THE GOLDMUND GOLDCUBE
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>THE</strong> <strong>GOLDMUND</strong> <strong>GOLDCUBE</strong><br />
Swiss Made
ATTENTION<br />
No connection or manipulation must be done before reading<br />
those instructions. Damage to the amplifier may result if the<br />
following instructions are not consciously understood and<br />
applied.<br />
UNPACKING<br />
You will find in the <strong>GOLDMUND</strong> GOLD CUBE packing :<br />
- A pair of the amplifiers,<br />
- This manual,<br />
- Accessories and spare fuses.<br />
Please keep the packaging in case you need to transport the<br />
amplifiers at a later date or if you have to send them for maintenance.<br />
CHOICE OF AMPLIFIER LOCATION AND COOLING<br />
The <strong>GOLDMUND</strong> GOLD CUBE has been designed to be used in<br />
combination with the GoLDMUND APOLOGUE speaker system,<br />
in the special lodging of its back panel. In this case, the<br />
amplifier is automatically reaching its proper temperature of<br />
f unction for optimized performances.<br />
lf used in a different configuration, do not forget that the GOLD<br />
CUBE, as all the high quality amplifiers. generates a large amount<br />
of heat.<br />
It is mandatory to allow a proper cooling of the body of the GO LD<br />
CUBE which acts as heat sink. Avoid a location which is not<br />
properly vented.
LINE VO LTAGE ADJUSTMENT<br />
The <strong>GOLDMUND</strong> GOLD CUBE amplifier is internally wired for a<br />
specif ic line voltage.<br />
ATTENTION : A 234V adjusted amplifier will function properly<br />
f or AC line voltage between 2OOV and 245Y . For<br />
a 1 1 7V version, the AC line must deliver between<br />
105 and 125V. lf your AC line is usually out of<br />
these tolerances, please consult your <strong>GOLDMUND</strong><br />
dealer.<br />
Please check the value of the main line f use. This f use is located<br />
on the bottom of the amolifier, near a corner.<br />
The golden lid can be removed with a smallscrewdriver or better<br />
with a coin, and then the f use holder.<br />
Use a 3A slow-blow fuse for 22OV and a 5A slow-blow fuse for<br />
1 10V.<br />
4. CONNECTIONS<br />
Connectthe power cord of the amplifier in the nearest wall plug.<br />
Use only a 3 lugs grounded plug, for safety reasons. To get the<br />
best sound of the amplif ier, avoid any multiple plug or extension<br />
cord.<br />
Connect the interconnect between the preamp and the power<br />
amp. The RCA female socket is the highest quality WBT socket<br />
(ground connectsfirst and the plug may be locked if you use the<br />
<strong>GOLDMUND</strong>-M lT interconnect).<br />
lf the GOLD CUBE is used with an APOLOGUE, use the provided<br />
bi-male iunctions to plug it inside the special lodging in the<br />
speaker back. The proper position of the cube is when the power<br />
cord and the power switch are visible on the bottom angle of the<br />
cube from the outside.<br />
Otherwise, connectthe speaker cables tothe two banana receptacle<br />
located on the opposite face from the input. The " + " is<br />
marked with a red dot.<br />
The amplifier is non-inverting in phase.<br />
-2-
5.1<br />
AMPLIFIERS CONTROLS<br />
On the front plate of the <strong>GOLDMUND</strong> GOLD CUBE are only<br />
accessible:<br />
The power key, used to power the amp on.<br />
When activated. the speaker is connected after a very short<br />
delay and the red LED switches on. The amp is powered off by<br />
switching off the power key. The red led will fade very slowly,<br />
indicating discharge of the filtering capacitors and the speaker<br />
will be disconnected after few seconds.<br />
5 .2 The two rail fuse sockets.<br />
Each rail fuse holder is protected by a golden lid. which can be<br />
removed using a coin. A red point LED, located near the fuse<br />
indicate that the fuse is burned when it glows.<br />
SOUND OUALITY OPTIM IZATION<br />
6 .1 Warm-up sonic effect.<br />
lf the power amplifier has not been powered off for a few days,<br />
theoptimum sound quality is only reached after 3Ominutes. This<br />
delay has been optimized to be minimal and the sonic quality<br />
when lust powered on is much higher than other quality power<br />
amplif iers.<br />
6 .2 Speaker polarity.<br />
Even if you have a phase inverter on your preamplif ier (as on the<br />
<strong>GOLDMUND</strong> MIMESIS 2 or MIMESIS 7). and even if you have<br />
carefully selected the proper line phase (see in next paragraph),<br />
there is a possibility to again increase the sonic quality of your<br />
speakers by reverting the polarity of the speaker cable amp<br />
termination. But since the line phase and the speaker polarity<br />
interfere to each other, you have to experiment carefully all the<br />
combinations before picking the right one.<br />
lf your preamp has an absolute phase inverter, this will interfere<br />
too. lf it has not, don'tforgetthe result willdepend of the source.<br />
most of the record and CD being recorded without care for the<br />
absolute phase. Be patient..<br />
-3-
6.3 Main line ohase inversion.<br />
The sonic quality of your GOLD CUBE may be slightly improved<br />
if the main AC line is properly connected. Try to invert the plug<br />
of your amplifier, using a special adapter.<br />
We recommend that you proceed caref ully to try this. You must<br />
do it in combination with the speaker polarity and/or with absolute<br />
phase switching to be sure of the result.<br />
7.1<br />
7.2<br />
t.5<br />
SAFETY FEATURES<br />
The <strong>GOLDMUND</strong> GOLD CUBE amplifier provides very sophisticated<br />
features to protectthe amplifierandthe speaker against all<br />
kind of mishandle or comoonent failure.<br />
Protection against DC.<br />
The GOLD CUBE is a DC-coupled amplifier. lf the associated<br />
preamplifier is badly designed or defective (often true for the<br />
tube preamps), the speaker could be damaged. The detection<br />
circuit of the GOLD CUBE is totally immune to any sonic effect<br />
but will immediately switch off the speaker if such a malf unction<br />
occurs.<br />
The speaker will be immediately and automatically reconnected<br />
as soon as the perturbation disappears.<br />
Protection against HF oscillations.<br />
In the same way, the speaker will be disconnected if a large<br />
amount of high frequency oscillation is present and shows a<br />
danger forthe tweeters, even if these frequencies remain unnoticed.<br />
The amplifier returns to normal if the oscillation disappears.<br />
Protection against short-circuits.<br />
lf one output is short-circuited by accident and the current<br />
becomes too high, one of the rail fuse may blow.<br />
In this case, the small LED located at the top ofthe defective fuse<br />
lid will glow.<br />
To replace the defective fuse, switch the amplifier off for 1O<br />
minutes f irst. Then open the top f use cover with a coin or a large<br />
screwdriver. The f use loader is then accessible under the golden<br />
cover and must be removed by turning it off with a screwdriver.<br />
-4-
You must use a 5 Amps fast f use (or 6.3 Amps if you use very low<br />
efficiency speakers) or 8 Amps ultra-fast.<br />
Then put the cover back in position and switch the power on if<br />
the short-circuit has been detected and removed.<br />
To avoid the f uses to blow, avoid to short-circuit the outDut<br />
terminals accidentally.<br />
There is no risk to leave the soeaker terminals unconnected<br />
when the amo is on,<br />
8. MAINTENANCE<br />
The <strong>GOLDMUND</strong> GOLD CUBE is gold plated with a 1O microns<br />
18kt gold layer, using the best ieweler technology. lt should<br />
never alter externally, except if mishandled.<br />
To clean the amplifier, use a very soft cloth to avoid scratching<br />
the gold surface.<br />
Otherwise the <strong>GOLDMUND</strong> GOLD CUBE amplifier requires no<br />
maintenance. For the audio purist who wants to keep his amp<br />
sounding as new. we only recommend that after a year or two,<br />
you have a technician or an official <strong>GOLDMUND</strong> representative<br />
readjustthe DC offset. Thisvery simple operation takes onlytwo<br />
minutes and will give you the safety of long years of unmatched<br />
sound quality.<br />
IMPORTANT NOTICE :<br />
The Goldcube should never be left powered on, without input<br />
cable connection to a preamplifier. lf warmed up without connection.<br />
please insert short-circuit plugs delivered with the cube<br />
to avoid any RF oscillation.<br />
-5-
TECHNICAL<br />
DATA<br />
POWER<br />
- Nominalpower : loowRMS(2-8Ohmsl.<br />
60 W RMS l1 - 16 Ohmsl.<br />
- Msximum power : l50WRMS13Ohms).<br />
- Maximumvoltag6: 35Vpeak.<br />
- Maximum cu,,cnt: 20 A Doak.<br />
FREOUENCY RESPONSE<br />
Th6sa figuros are valil for any levet between 0and nominal power.<br />
- +/- O.l d8. O. IOO kHz.<br />
- +/. I dB,0 - 40O kHz.<br />
- +/.3d8,0 - 0.9 MHz.<br />
INPUT SENSITIVITY<br />
- Nominallevel : 1.55 V (+6dBl.<br />
- Inout im9odanca : 50 kohms.<br />
GROUP O€LAY<br />
- Propagarion delay < lOO ns stablG with tr6quency lrom OC to 20O kHz.<br />
DISTORTION<br />
Figlre3 vElid ,or 8ll lovels f.om 0 to 25 V / Iohns.<br />
- Dynamic : TID l0o dB.<br />
OPERATING TEMPERATURE<br />
- Room l€mpsraturo : -3O to +4O dog,e6s Calsius (-22 to + 1O4 dsgr€ss F8h'rnhoitl.<br />
- In$m€ltsmpeGtu.e : +45to + 65 dogrees Colsius { + 1 l3 to + 149dcgr€ca Fah.6nheit}.<br />
POWER SUPPLY<br />
- Nominsllins volt'gs I 10O, 117,or23V.<br />
- Inp{t volt8ge ranga : +/- 10%.<br />
- Maximum powga co{Eumption : 250 W.<br />
SAFETY F€ATURES<br />
- DC protsction th.oshold : 5V.<br />
- HF protefiioo thr€shold : 3VRMSat50kHz.<br />
- Inprrr voltag€ fuso | 3Adow{lowfo.22OVlSAstow.btowfo. llOV.<br />
- Shon.ci,cuit o.otrction : 2 fu36 5 A fasr,<br />
SIZE ANO W€IGHT<br />
- 12.7 cm l5"l wx l2.7cm (5'l Dx 12.7 cm {5"} H.<br />
- Weighr : 7 kG net.<br />
-6-