fitting instructions for diamond quadrant surround - Image Showers

FITTING INSTRUCTIONS
FOR DIAMOND QUADRANT
SURROUND
1.
2.
FITTING KIT
SEAL BOTTOM OF FIXED PANELS B
DOOR
STOPS
TOOLS YOU WILL NEED
IMAGE
SHOWERS
Sticker to be added after installation
N.B Guarantee is not valid unless
logo sticker is placed on the door.
FIT BOTH THE CURVED RAILS D + D1
TO ONE OF THE FLAT PANELS B USING
THE SCREWS H
Outside
ATTENTION!
PLEASE INSPECT CONTENTS IMMEDIATELY ON RECEIPT FOR
ANY DAMAGE CAUSED DURING TRANSIT. ANY CLAIMS
MADE LATER CANNOT BE ACCEPTED
BEFORE INSTALLING THE SHOWER DOOR CHECK THAT THE
TRAY IS LEVEL AND PROPERLY SEALED AT THE WALL. THE
ENCLOSURE WHEN COMPLETED MUST NOT OVERHANG
THE OUTSIDE OF THE TRAY. CHECK THE OPERATION OF THE
DOOR BEFORE SEALING.
3.
IMAGE SHOWERS ARE DESIGNED TO BE INSTALLED OVER
TILING. THE TRAY MUST BE PROPERLY SEALED ALL AROUND
THE EDGES WHERE IT MEETS THE TILING AND OR WALLS
LEVEL TRAY AND SEAL
Seal gap under wall profile and around tray
Seal gap under wall profile and around tray
ALWAYS USE A
GOOD QUALITY
SILICON SEALANT
WHERE INDICATED
INSTALL THE WALL PROFILES A
MAKE SURE THEY ARE POSITIONED AS SHOWN
1. THE RIGHT WAY AROUND
2. 10MM IN FROM THE EDGE OF THE TRAY
3. THE PROFILES MUST BE VERTICLE. USE A SPIRIT LEVEL AS
SHOWN
4. MARK THE POSITION FOR DRILLING THROUGH THE PRE DRILLED
HOLES IN THE PROFILE
5. REMOVE THE PROFILES AND DRILL THE HOLES USING A 5.5mm
MASONRY DRILL BIT, THEN INSERT THE PLUGS G PROVIDED.
6. REPLACE THE PROFILES AND SECURE USING SCREWS H
Handle
Wiper
SLIDE ONE OF THE CURVED
DOORS C
INTO THE ASSEMBLED RAILS.
MAKE SURE THAT THE WIPER
SIDE IS INSERTED FIRST AND
THAT THE WHEELS ARE
ALIGNED TOP AND BOTTOM

Top to bottom
4.
ADJUST THE FRAME TO OBTAIN AN EVEN FIT
BETWEEN THE WALL PROFILES, MAKING SURE THE
MOVING DOORS CONTINUOUSLY MEET TOP TO
BOTTOM IN THE MIDDLE. DO NOT ALLOW THE
DOOR TO OVERLAP THE OUTER EDGE OF THE TRAY.
Wiper
Handle
10CM
5.
Outside
Inside
VIEW FROM INSIDE
DO NOT FORGET TO SEL
UNDERSIDE OF PROFILE B
LIFT THE ASSEMBLED DOOR ONTO
THE TRAY AND LOCATE INTO THE
PROFILES SHOWN IN 1. YOU MAY
NEED THE ASSISTANCE OF
ANOTHER PERSON TO DO THIS
SLIDE THE SECOND CURVED DOOR C
INTO THE ASSEMBLED RAILS. MAKE SURE THE HANDLE SIDE IS
INSERTED FIRST AND THAT THE WHEELS ARE CORRECTLY ALIGNED
TOP AND BOTTOM. SLIDE THE SECOD FLAT PANEL B IN BETWEENTHE
TOP AND BOTTOM RAILS AND FIX USING THE 4 SCREWS H
FIT ALL 8 DOOR STOPS L TO
THE INSIDE OF THE TOP AND
OTTOM RAILS WITH SCRES K
IN PRE DRILLD HOLES
WORKING FROM THE INSIDE FIX THE DOOR TO THE
WALL PROFILES BY DRILLING THROUGH THE PRE-DRILLED
“V” SHAPED GROOVE AND INTO THE DOOR PROFILE
WITH THE 2.8mm DRILL BIT. USE 4 SCREWS TO SECURE
THE DOOR AT EACH SIDE
IMPORTANT
SEAL INSIDE UPRIGHTS
ONLY AND OUTSIDE
BOTTOM ONLY AS
SHOWN WITH A HIGH
QUALITY SILICON
SEALANT. DO NOT SEAL
AT BOTTOM BETWEEN
TRAY AND DOOR ON
THE INSIDE
10CM
SEAL OUTSIDE ONLY
6. 7.
8.