Process Guidance Note 6/34(11) - Defra

More documents

Recommendations

Info

About compliant coatings Note a – High solvent content wash primers should only be used where it is necessary to achieve adhesion of subsequent coats on difficult, bare metal, surfaces such as aluminium, zinc plates, or galvanised metals. The use of such wash primers should be limited to not more than 5% of the total coatings material usage except where etch primer is used to coat aluminium for the first time. Special Finishes Where a special finish is supplied by the manufacturer or distributor to the limit shown in Table 4.2 relates to the coating, as applied Where a special finish is prepared from the mixing of an additive and a standard product, the permitted solvent content of the coating, as applied, will comply with the limit in Table 4.2. The permitted solvent content is determined as follows: Permitted solvent concentration = (M x S3) + (N x S4) + (P x S5) g/l less water in the coating as 100 applied Where M is the percentage of the additive, less any water present in the additive, in the coating as applied. S3 is the organic solvent content of the additive (g/1 less water) N is the percentage of the standard product, less any water present in the produce, in the coating as applied S4 is the permissible solvent content of the standard product (see Table 4.2). P is the percentage of added thinners, less any water present in the thinners, in the coating as applied S5 is the solvent content of the thinners PG6/34(11) 32
Appendix 1: Application form Application for a permit to operate a vehicle refinishing installation Local Authority Pollution Prevention and Control Pollution Prevention and Control Act, 1999 The Environment (Northern Ireland) Order 2002 The Pollution Prevention and Control (Industrial Emissions) Regulations (Northern Ireland) 2012 Environmental Permitting (England and Wales) Regulations 2010 (as amended) Introduction When to use this form Use this form if you are applying to a Local Authority for a permit to operate a vehicle refinishing installation as defined in Environmental Permitting Regulations (England and Wales) Regulations 2010 (as amended) or the Pollution Prevention and Control Regulations (Northern Ireland) 2003. The appropriate fee must be enclosed with the application to enable it to be processed further. When complete send the form and fee and any additional information to: [Insert local authority address] If you need help and advice We have made the application form as straightforward as possible, but please get in touch with us at the local authority address given above if you need any advice on how to set out the information we need. For the purposes of Section C of the form, a relevant offence is any conviction for an offence relating to the environment or environmental regulation. For Local Authority use Application reference Officer reference Date received PG6/34(11) 33
Page 1 and 2: www.gov.uk/defra Process Guidance N
Page 3 and 4: Defra would like to acknowledge the
Page 5 and 6: Contents Revision of the guidance .
Page 7 and 8: 1. Introduction Legal basis 1.1 Thi
Page 9 and 10: Updating the guidance 1.9 The guida
Page 11 and 12: Temporary location of a SMART repai
Page 13 and 14: Permit reviews 2.7 Under LAPPC, the
Page 15 and 16: Application Methods 3.5 Most coatin
Page 17 and 18: Seam sealing 3.17 Weld seams and jo
Page 19 and 20: Figure 3.1 - Potential VOC releases
Page 21 and 22: VOC compliant coatings 4.4 Complian
Page 23 and 24: Visible emissions 4.8 The aim shoul
Page 25 and 26: 5. Control techniques Summary of be
Page 27 and 28: 5.9 Where no such guarantee is obta
Page 29 and 30: General control techniques Dust and
Page 31 and 32: An exception to the previous paragr
Page 33 and 34: 6. Summary of changes The main chan
Page 35 and 36: these limits may differ since they
Page 37: 8.4 The volatile content of the coa
Page 41 and 42: A5 Any holding company? Is the oper
Page 43 and 44: B6 Provide detailed procedures and
Page 45 and 46: B22 Additional Information Please s
Page 47 and 48: C4 C5 Data Protection Declaration T
Page 49 and 50: Conditions Non-VOC emissions Table
Page 51 and 52: 13. Spray applied coatings shall be
Page 53 and 54: The following two conditions are no

Process Guidance Note 6/34(11) - Defra

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?