netGateway DTM for netTAP, netBRICK and netLINK - Hilscher

More documents

Recommendations

Info

Configuration 126/256 5. Open the signal configuration dialog ‣ Select in the navigation area under the folder Configuration the entry Signal Configuration. The signal configuration dialog opens 6. Signal configuration ‣ If you want to assign own signal names, then enter your signal names. Further information is described in section Signal Configuration on page 222. 7. Close configuration dialog ‣ Click on OK to save the parameter or click on Cancel, if the parameter should not be saved. The configuration dialog closes netGateway DTM for netTAP, netBRICK and netLINK | Configuration of Gateway and Proxy Devices DOC081201OI04EN | Revision 4 | English | 2011-03 | Released | Public © Hilscher, 2009-2011
Configuration 127/256 4.9.1 EtherNet/IP Adapter Parameter Parameter Meaning Range of Value/Value Interface Bus Startup Communication starts automatically Automatic (Default) Watchdog Time [ms] This function is not supported by gateway or proxy devices. [0, 20 … 65535] ms, default = 1000 ms, 0 = Off I/O Data Status Status of the input or the output data. Default: None For each input and output data the following status information (in Byte) is memorized in the dual-port memory: Status 0 = None (default) Status 1 = 1 Byte (for future use) Status 2 = 4 Byte (for future use) Ident Enabled If ‘Enabled’ is unchecked, for the single Ident parameters each the respective default value is used. Vendor ID Identification number of the manufacturer 0x00000000 ... 0x0000FFFF (hex), Hilscher: 0x00000011B (hex) Product Code Product code of the device as specified by the manufacturer 0x00000000 ... 0x0000FFFF (hex), Default NT 50-EN/EIS: 0x000000113 (hex), NT 100-RE/EIS: 0x00000010F (hex), NB 100-RE/EIS: 0x000000111 (hex) Product Type Communication Adapter 0x00000000 ... 0x0000FFFF (hex), Default: 0x00000000C (hex) Major Rev Major Revision 0 ... 255, Default: 1 Minor Rev Minor Revision 0 ... 255, Default: 1 Device name Device name of the device station as character string, 0 - 31 ASCII characters e. g. EtherNet/IP Adapter (Slave). Bus IP Address Netmask Valid IP Address for the device If ‘Enabled’ is unchecked (Default setting), the device obtains its IP Address from a DHCP server or also from a BOOTP server, if this one is checked. If ‘Enabled’ is checked, the device uses the manually entered value. Valid Network mask for the device If ‘Enabled’ is unchecked (Default setting), the device obtains its Netmask from a DHCP server or also from a BOOTP server, if this one is checked. If ‘Enabled’ is checked, the device uses the manually entered value. Table 18: EtherNet/IP Adapter Parameters (Part 1) Valid IP address Default: unchecked Valid network mask Default: unchecked netGateway DTM for netTAP, netBRICK and netLINK | Configuration of Gateway and Proxy Devices DOC081201OI04EN | Revision 4 | English | 2011-03 | Released | Public © Hilscher, 2009-2011
Page 1 and 2:
Operating Instruction Manual netGat
Page 3 and 4:
Introduction 3/256 2.3.10 Load Conf
Page 5 and 6:
Introduction 5/256 4.23.3 Modbus RT
Page 7 and 8:
Introduction 7/256 1.1.1 Online Hel
Page 9 and 10:
Introduction 9/256 1.2 Legal Notes
Page 11 and 12:
Introduction 11/256 1.2.5 Export Re
Page 13 and 14:
Introduction 13/256 1.4 Dialog Stru
Page 15 and 16:
Introduction 15/256 1.4.3 Dialog Pa
Page 17 and 18:
Introduction 17/256 1.4.5 Status Ba
Page 19 and 20:
Configuration Sequence for Gateway
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76: Configuration Sequence for Gateway
Page 85 and 86: Settings 85/256 3.2 Driver The devi
Page 87 and 88: Settings 87/256 3.2.3 netX Driver T
Page 89 and 90: Settings 89/256 Parameter Meaning R
Page 91 and 92: Settings 91/256 3.2.3.3 Driver Para
Page 93 and 94: Settings 93/256 3.2.4 Configure net
Page 95 and 96: Settings 95/256 Parameter Meaning R
Page 97 and 98: Configuration 97/256 4 Configuratio
Page 99 and 100: Configuration 99/256 4.3 Licenses 4
Page 101 and 102: Configuration 101/256 4.3.3 Which L
Page 103 and 104: Configuration 103/256 4.3.4 How to
Page 105 and 106: Configuration 105/256 4.3.6.2 Data
Page 107 and 108: Configuration 107/256 4.3.7.1 Order
Page 109 and 110: Configuration 109/256 The order da
Page 111 and 112: Configuration 111/256 4.3.8 How to
Page 113 and 114: Configuration 113/256 On the pane I
Page 115 and 116: Configuration 115/256 4.4.1 Status
Page 117 and 118: Configuration 117/256 Communication
Page 119 and 120: Configuration 119/256 4.5 Memory Ca
Page 121 and 122: Configuration 121/256 4.7 Configura
Page 123 and 124: Configuration 123/256 4.7.2 Setting
Page 125: Configuration 125/256 4.9 Configura
Page 129 and 130: Configuration 129/256 4.9.2 Setting
Page 131 and 132: Configuration 131/256 4. Command Ta
Page 133 and 134: Configuration 133/256 Parameter Mea
Page 135 and 136: Configuration 135/256 4.10.2.2 Para
Page 139 and 140: Configuration 139/256 4.10.2.5 Exam
Page 141 and 142: Configuration 141/256 Register or C
Page 143 and 144: Configuration 143/256 6. Open the s
Page 147 and 148: Configuration 147/256 4.12 Configur
Page 151 and 152: Configuration 151/256 4.13.2 Settin
Page 155 and 156: Configuration 155/256 8. Set Output
Page 157 and 158: Configuration 157/256 4.15.1 SERCOS
Page 167 and 168: Configuration 167/256 Data Send Obj
Page 171 and 172: Configuration 171/256 4.18.1 CC-Lin
Page 177 and 178:
Configuration 177/256 4.20.1 Device
Page 179 and 180:
Configuration 179/256 4.20.2 Settin
Page 181 and 182:
Configuration 181/256 4.22 Configur
Page 183 and 184:
Configuration 183/256 4.22.1 PROFIB
Page 185 and 186:
Configuration 185/256 4.22.2 Settin
Page 187 and 188:
Configuration 187/256 5. Open the s
Page 189 and 190:
Configuration 189/256 Parameter Mea
Page 191 and 192:
Configuration 191/256 4.23.2.2 Para
Page 193 and 194:
Page 195 and 196:
Configuration 195/256 4.23.2.5 Exam
Page 197 and 198:
Configuration 197/256 4.23.3 Modbus
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Configuration 205/256 4.25.1 ASCII
Page 207 and 208:
Configuration 207/256 Parameter Des
Page 209 and 210:
Configuration 209/256 ASCII Hex ASC
Page 211 and 212:
Configuration 211/256 4.25.2.4 ‘S
Page 213 and 214:
Configuration 213/256 4.25.2.5 'Rec
Page 215 and 216:
Configuration 215/256 4.25.2.6 Clie
Page 217 and 218:
Configuration 217/256 Configuration
Page 219 and 220:
Configuration 219/256 Configuration
Page 221 and 222:
Configuration 221/256 4.26.1 netSCR
Page 223 and 224:
Diagnosis 223/256 5 Diagnosis 5.1 O
Page 225 and 226:
Diagnosis 225/256 Indication Device
Page 227 and 228:
Diagnosis 227/256 5.3 Firmware Diag
Page 229 and 230:
Online Functions 229/256 Disconnect
Page 231 and 232:
Error Codes 231/256 7 Error Codes 7
Page 233 and 234:
Error Codes 233/256 7.3 General Har
Page 235 and 236:
Error Codes 235/256 7.3.2 RCX Error
Page 237 and 238:
Error Codes 237/256 7.4 ODM Error C
Page 239 and 240:
Error Codes 239/256 7.4.3 ODM cifX
Page 241 and 242:
Error Codes 241/256 ID of the Error
Page 243 and 244:
Error Codes 243/256 7.5 ODM DBM V4
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Lists 249/256 8 Lists 8.1 List of F
Page 251 and 252:
Lists 251/256 8.2 List of Tables Ta
Page 253 and 254:
Glossary 253/256 9 Glossary DTM FDT
Page 255 and 256:
Appendix 255/256 10.2 References [1
show all

netGateway DTM for netTAP, netBRICK and netLINK - Hilscher

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?