BMW D7 Workshop Manual

More documents

Recommendations

Info

Starter Motor Starter Motor Removal - Disconnect cables A from solenoid (connector 19mm) and remove insulation B - Remove fixing nuts C (19mm) and detach earth strap D from upper stud - Lift off starter motor When faulty renew. 39
Water pump Service Instructions A. Disassembly - Remove cover screws, cover and gasket - Press out impeller with 2 screwdrivers - After removing the cam, remove residual traces of sealing compound from cam and pump housing - Remove lip seal and O-ring - Remove bearing assembly circlip - Remove the shaft with ball bearing by pressing in the impeller side of the shaft - Press off the ball bearings from the shaft. Do not press the ball bearings over the sealing surface of the shaft B. Assembly - Press the ball bearings on to the shaft. Do NOT press the ball bearings over the sealing surface of the shaft - Press the shaft with ball bearings into the pump housing and fit the circlip and sealing plates (11) - Assemble O-ring and sealing plate with the opening towards the impeller - Fasten the cam, before doing so, apply sealing compound to cam and screw to prevent leakage - Lubricate the im peller and fit it with a rotating movement in the intended direction of impeller rotation - Fit a new gasket before mounting the cover Weight and Dimensions Type: Dimension B Weight F35B-8 12.5 0.5kg Performance Table F35B-8 Impeller Neoprene Kp/cm 2 500 rpm kW l/min 700 rpm kW l/min 900 rpm kW l/min 1400 rpm kW l/min 2000 rpm kW l/min 2500 rpm kW l/min 0.3 0.6 1.0 0.06 0.06 0.06 3.6 3.4 2.7 0.06 0.09 0.09 5.2 4.6 4.0 0.09 0.09 0.09 6.8 6.2 5.6 0.13 0.13 0.13 11.2 10.6 9.2 0.18 0.18 0.18 16.0 15.8 13.6 0.18 0.18 0.18 20.5 19.6 17.0 Performance stated is for new pumps and water at room temperature 40
Page 1 and 2: Workshop Manual BMW D7 BMW Marine T
Page 3 and 4: Contents Page Page Introduction i F
Page 5 and 6: List of Special Tools D7 BMW Part N
Page 7 and 8: Summary 21. Exhaust 22. Starter 23.
Page 9 and 10: Cylinder Head - Remove rocker shaft
Page 11 and 12: Cylinder Head The valves should sit
Page 13 and 14: Bearing cover Remove starter (13) -
Page 15 and 16: Cover to timing gear cover / timing
Page 17 and 18: Table: Repair data for connecting r
Page 19 and 20: Fuel pump / timing gear cover - Rem
Page 21 and 22: Ball sleeve / Crankshaft - Remove b
Page 23 and 24: Table: Repair data for crankshaft R
Page 25 and 26: Camshaft Crankshaft Reassembly of t
Page 27 and 28: Flywheel / Stator / Reversing Gear
Page 29 and 30: Timing gear adjustment Adjust valve
Page 31 and 32: Timing gear adjustment Correction i
Page 33 and 34: Injection pump - Adjust the injecti
Page 35 and 36: Injection pump NOTE Slide the pump
Page 37 and 38: Injection pump / Injector Venting I
Page 39 and 40: Wiring diagram 34
Page 41 and 42: Generator and generating equipment
Page 43: Generator and generating equipment

BMW D7 Workshop Manual

Create successful ePaper yourself

Delete template?

Save as template?