Digital outputs and temperature sensors - USB-Ourput-Device - ipcas
Digital outputs and temperature sensors - USB-Ourput-Device - ipcas
Digital outputs and temperature sensors - USB-Ourput-Device - ipcas
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>USB</strong>-Output-<strong>Device</strong><br />
<strong>Digital</strong> <strong>outputs</strong> <strong>and</strong> <strong>temperature</strong> <strong>sensors</strong><br />
Control digital <strong>outputs</strong> via <strong>USB</strong> or readout<br />
<strong>temperature</strong> <strong>sensors</strong>.<br />
The <strong>USB</strong>-Output-<strong>Device</strong> provides digital interfaces to<br />
control output signals directly from the <strong>USB</strong> port on a<br />
PC or embedded system.<br />
The device is particularly well suited for:<br />
• Control of digital <strong>outputs</strong>, depending on the<br />
<strong>temperature</strong><br />
• Output of a digital state<br />
• Pulse output (variable pulse length)<br />
• Output of a PWM signal<br />
• Output of predetermined pulses number<br />
The <strong>Device</strong> is equipped with four electrically isolated digital output channels <strong>and</strong> a <strong>temperature</strong>-single-wire bus<br />
for up to six <strong>temperature</strong> <strong>sensors</strong>, therefore the <strong>outputs</strong> can be specifically controlled.<br />
Also implemented is a st<strong>and</strong>-alone <strong>and</strong> <strong>temperature</strong>-dependent control of the digital <strong>outputs</strong>.<br />
The voltage supply for the <strong>USB</strong>-Output-<strong>Device</strong> is provided directly via <strong>USB</strong>.<br />
The <strong>temperature</strong> <strong>sensors</strong> <strong>and</strong> <strong>outputs</strong> are connected via industrial screw terminals.<br />
The several output channels can be controlled with the clear <strong>and</strong> simple designed configuration software,<br />
individually.<br />
Specifications<br />
<strong>USB</strong>-Output-<strong>Device</strong> Table-top device DIN-Rail Unit<br />
‣ 1x 1 x <strong>USB</strong> 1.1 socket Typ B (<strong>USB</strong> 2.0 compatible)<br />
Interfaces<br />
‣ 4x P-channel output MOSFET with 2x VCC input <strong>and</strong> 2x GND<br />
Separate channels: 500 V galvanic isolation in two groups<br />
Isolation voltage:<br />
1000 V to <strong>USB</strong><br />
ESD protection:<br />
> 30 V DC by TVS diodes<br />
Output voltage:<br />
24 V DC (20 -28 V DC)<br />
Input current:<br />
max. 500mA at 24V<br />
Line cross sectionsection: 0,08 ... 1,5 mm (AWG 28 ... 16)<br />
Frequency:<br />
max. 100 Hz<br />
‣ 6x Temperature sensor DS18S20:<br />
(-10°C to +85°C with ±0,5°C accuracy)<br />
(-55°C to +125°C with ±2°C accuracy)<br />
Voltage supply<br />
+ 5 V DC via <strong>USB</strong><br />
Power consumption<br />
max. 500 mA, typical 80 mA<br />
Casing, Measurements W/H/D Plastic, approx. 72 / 25 / 50 mm Plastic, approx. 25 / 72 / 64 mm<br />
Operating/Storage <strong>temperature</strong><br />
5° C to 55° C / -10° C to 70° C<br />
Relative humidity<br />
5 % to 90 % non-condensing<br />
Protection class<br />
IP30<br />
St<strong>and</strong>ards<br />
CE<br />
Scope of supply<br />
<strong>USB</strong>-Output-<strong>Device</strong><br />
Configuration software <strong>and</strong> manual are available on the internet.<br />
Purchase order number 0202049 0202049-H<br />
2011-11-18<br />
Subject to change without prior notice<br />
<strong>ipcas</strong> GmbH<br />
Gundstrase 15 Telefax +49 (0)9131/ 7677-78<br />
D-91056 Erlangen Internet http://www.<strong>ipcas</strong>.de<br />
Phone +49 (0)9131/ 7677-0 Email info@<strong>ipcas</strong>.de
<strong>USB</strong>-Output-<strong>Device</strong><br />
<strong>Digital</strong> <strong>outputs</strong> <strong>and</strong> <strong>temperature</strong> <strong>sensors</strong><br />
Control digital output signals via <strong>USB</strong>.<br />
Each digital output can be controlled separately.<br />
The digital <strong>outputs</strong> can also be controlled as a bit<br />
pattern.<br />
Control of digital <strong>outputs</strong>,<br />
depending on <strong>temperature</strong> values.<br />
Each digital output can be assigned to a <strong>temperature</strong> sensor.<br />
This configuration can only be set via the comm<strong>and</strong> console.<br />
The minimum hysteresis is adjustable to 2°C.<br />
turn on switch off <strong>temperature</strong><br />
Capturing <strong>and</strong> analysis of <strong>temperature</strong> values<br />
The DS18S20 <strong>temperature</strong> <strong>sensors</strong> are connected via a single-wire bus system on the <strong>USB</strong>-Output-<strong>Device</strong>.<br />
Temperatures of +125°C to -55°C can be detected. No external power supply is required.