Pneufit push-in fittings

More documents

Recommendations

Info

Pneufit C push-in fittings Inch Ø Â" to Ë" O/D tube PNEUFIT ® C MANIFOLDS Male Manifold Thread 1/4”-5/32” 5/16”-5/32” 5/16”-3/16” 5/16”-1/4” 3/8”-1/4” 1/8" NPT C24D30218 - - - - 1/4" NPT - C24D30228 C24D30328 C24D30428 - 3/8" NPT - - - - C24D30438 Manifold Union 3/16”- 5/32” 1/4”- 5/32” 5/16”- 5/32” 5/16”- 3/16” 5/16”- 1/4” 3/8”- 1/4” 3/8”- 5/16” C20D30302 C20D30402 C20D30502 C20D30503 C20D30504 C20D30604 C20D30605 Stem Manifold 3/16”- 5/32” 1/4”- 5/32” 5/16”- 5/32” 5/16”- 3/16” 5/16”- 1/4” 3/8”- 1/4” 3/8”- 5/16” C20J30302 C20J30402 C20J30502 C20J30503 C20J30504 C20J30604 C20J30605 FIT-17
Fittings Pneufit push-in fittings Metric Ø 4 to 14 mm O/D tube Compact units featuring retained collets and positive tube anchorage. Silicone free 'O'-ring seals. Non-PTFE based thread sealant on all BSP taper threads. Easy tube insertion for rapid assembly. Internal hexagon on straight adaptors allows assembly in confined spaces. Wide range of types available. Reliable and corrosion resistant. Specifications Fluid: Compressed air, nitrogen, inert and non-combustible gases compatible with materials of construction. For other types of fluids or compressed gases, please consult factory. Working Pressure: 750 mm Hg to 18 bar (29.5" Hg vacuum to 260 psig) Note: Flow Controls working pressures: .3 to 10 bar (5 to 150 psig) Working Temperature: -20° to 80°C (0° to 175°F) Request viton® option on selected part numbers for extended temperature range : - 20° to 180°C (0° to 350°F) Materials of Construction Body, swivel fitting and collet: Nickel plated brass O-ring: Silicone free Nitrile Sealing washer (parallel male threads): Silicon free nitrile Tubing: Nylon 11 or Nylon 12, Polyurethane (95 durometer or above) and LDPE (Low Density Polyethylene). Note: Lower durometer polyurethane may be used, however, an internal tube support is required to prevent internal collapse of the tube wall. Thread Sealant: Precote 5 thread sealant is factory applied to the circumference of tapered male threads (ISO R). FIT-18 V A ØS Dimensions mm (in.) T A T O.D. Tube S Tubing Stop V 4 (5/32") 2.8 (.11) 14.0 (.55) 7.5 (.30) 5 3.4 (.13) 15.0 (.59) 10.0 (.39) 6 4.4 (.17) 15.5 (.61) 11.0 (.43) 8 (5/16") 6.0 (.24) 16.5 (.65) 13.0 (.51) 10 7.6 (.30) 21.0 (.83) 14.5 (.57) 12 9.6 (.38) 24.5 (.96) 18.0 (.71) 14 11.5 (.45) 24.5 (.96) 20.0 (.79) Tube stop O-ring Internal hexagon Body Thread sealant Collet Recommended tightening torques Thread Tightening Torque Nm (ft lbs) Size ISO R ISO G* M5 — 1 - 1.4 (.75 - 1.05) 1/8 6.9 - 8.8 (5.0 - 6.5) 7 - 9 (5.3 - 6.8) 1/4 11.8 - 13.7 (8.7 - 10.0) 9 - 12 (6.8 - 9.0) 3/8 21.6 - 23.5 (15.9 - 17.3) 34 - 38 (25.5 - 28.5) 1/2 27.4 - 29.4 (20.2 - 21.7) 41 - 47 (30.8 - 35.3) *Lower torques can be used to achieve a seal but these figures are recommended to provide some vibration resistance. Tube O.D.'s and Tube Tolerances O.D. Tube Tolerances Tube O.D. Nylon Polyurethane 4 mm to 5 mm +0.05 mm (+0.002") (5/32" to 3/16") -0.07 mm (-0.003") 6 mm to 14 mm +0.05 mm (+0.002") ±0.10 mm (±0.004") (1/4" to 1/2") -0.10 mm (-0.004") LDPE –Tolerances specified in DIN 73378 or BS54-09/1:1976 www.norgren.com/info/US-FIT-18
Page 1 and 2: Fittings Pneufit push-in fittings I
Page 7 and 8: Fittings Pneufit ® C composite and
Page 9 and 10: Fittings Pneufit C push-in fittings
Page 15: Fittings Pneufit C push-in fittings
Page 19 and 20: Fittings Pneufit push-in fittings M
Page 25 and 26: Pneufit ® C composite and Pneufit
Page 35 and 36: Pneufit ® D fittings Metric Ø 4mm
Page 37 and 38: Pneufit ® D fittings Metric Ø 4mm
Page 39 and 40: ACCESSORIES Pneufit ® D fittings M
Page 41 and 42: Pneufit ® D fittings Inch Ø 5/32"
Page 43 and 44: Pneufit ® D fittings Inch Ø 5/32"
Page 45: Pneufit D fittings Inch Ø 5/32" to

Pneufit push-in fittings

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?