You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Fitt<strong>in</strong>gs<br />
<strong>Pneufit</strong> <strong>push</strong>-<strong>in</strong> fitt<strong>in</strong>gs<br />
Metric<br />
Ø 4 to 14 mm O/D tube<br />
Compact units featur<strong>in</strong>g<br />
reta<strong>in</strong>ed collets and positive<br />
tube anchorage.<br />
Silicone free 'O'-r<strong>in</strong>g seals.<br />
Non-PTFE based thread sealant<br />
on all BSP taper threads.<br />
Easy tube <strong>in</strong>sertion for rapid<br />
assembly.<br />
Internal hexagon on straight<br />
adaptors allows assembly <strong>in</strong><br />
conf<strong>in</strong>ed spaces.<br />
Wide range of types available.<br />
Reliable and corrosion<br />
resistant.<br />
Specifications<br />
Fluid: Compressed air, nitrogen,<br />
<strong>in</strong>ert and<br />
non-combustible gases<br />
compatible with materials of<br />
construction. For other types of<br />
fluids or compressed gases,<br />
please consult factory.<br />
Work<strong>in</strong>g Pressure: 750 mm Hg to<br />
18 bar<br />
(29.5" Hg vacuum to 260 psig)<br />
Note: Flow Controls work<strong>in</strong>g<br />
pressures:<br />
.3 to 10 bar (5 to 150 psig)<br />
Work<strong>in</strong>g Temperature: -20° to<br />
80°C (0° to 175°F)<br />
Request viton® option on<br />
selected part numbers for<br />
extended temperature range : -<br />
20° to 180°C (0° to 350°F)<br />
Materials of<br />
Construction<br />
Body, swivel fitt<strong>in</strong>g and collet:<br />
Nickel plated brass<br />
O-r<strong>in</strong>g: Silicone free Nitrile<br />
Seal<strong>in</strong>g washer (parallel male<br />
threads): Silicon free nitrile<br />
Tub<strong>in</strong>g: Nylon 11 or Nylon 12,<br />
Polyurethane (95 durometer or<br />
above) and LDPE (Low Density<br />
Polyethylene).<br />
Note: Lower durometer<br />
polyurethane may be used,<br />
however, an <strong>in</strong>ternal tube support<br />
is required to prevent <strong>in</strong>ternal<br />
collapse of the tube wall.<br />
Thread Sealant: Precote 5 thread<br />
sealant is factory applied to the<br />
circumference of tapered male<br />
threads (ISO R).<br />
FIT-18<br />
V<br />
A<br />
ØS<br />
Dimensions mm (<strong>in</strong>.)<br />
T<br />
A<br />
T<br />
O.D. Tube S Tub<strong>in</strong>g Stop V<br />
4 (5/32") 2.8 (.11) 14.0 (.55) 7.5 (.30)<br />
5 3.4 (.13) 15.0 (.59) 10.0 (.39)<br />
6 4.4 (.17) 15.5 (.61) 11.0 (.43)<br />
8 (5/16") 6.0 (.24) 16.5 (.65) 13.0 (.51)<br />
10 7.6 (.30) 21.0 (.83) 14.5 (.57)<br />
12 9.6 (.38) 24.5 (.96) 18.0 (.71)<br />
14 11.5 (.45) 24.5 (.96) 20.0 (.79)<br />
Tube stop<br />
O-r<strong>in</strong>g<br />
Internal hexagon<br />
Body<br />
Thread sealant<br />
Collet<br />
Recommended tighten<strong>in</strong>g torques<br />
Thread Tighten<strong>in</strong>g Torque Nm (ft lbs)<br />
Size ISO R ISO G*<br />
M5 — 1 - 1.4 (.75 - 1.05)<br />
1/8 6.9 - 8.8 (5.0 - 6.5) 7 - 9 (5.3 - 6.8)<br />
1/4 11.8 - 13.7 (8.7 - 10.0) 9 - 12 (6.8 - 9.0)<br />
3/8 21.6 - 23.5 (15.9 - 17.3) 34 - 38 (25.5 - 28.5)<br />
1/2 27.4 - 29.4 (20.2 - 21.7) 41 - 47 (30.8 - 35.3)<br />
*Lower torques can be used to achieve a seal but these figures are<br />
recommended to provide some vibration resistance.<br />
Tube O.D.'s and Tube Tolerances<br />
O.D. Tube Tolerances<br />
Tube O.D. Nylon Polyurethane<br />
4 mm to 5 mm +0.05 mm (+0.002")<br />
(5/32" to 3/16") -0.07 mm (-0.003")<br />
6 mm to 14 mm +0.05 mm (+0.002")<br />
±0.10 mm<br />
(±0.004")<br />
(1/4" to 1/2") -0.10 mm (-0.004")<br />
LDPE –Tolerances specified <strong>in</strong> DIN 73378 or BS54-09/1:1976<br />
www.norgren.com/<strong>in</strong>fo/US-FIT-18