General Information Gates/Rohloff - Koga Signature

More documents

Recommendations

Info

mounting Flat Wrench SW46 Art. Nr. 10400006 POM-Sprocket-Key Art. Nr. siehe Tabelle Title Part Number Basiswerkzeug 10400001 Aufsatz 19 Zähne 10400002 Aufsatz 20 Zähne 10400003 Aufsatz 22 Zähne 10400004 Aufsatz 24 Zähne 10400005 Mounting the Rear Sprocket M46x6 to the Gates-Rohloff Carrier M46x6 The Gates-Rohloff Carrier M46x6 by Rohloff (Art. No. 10300101) is where the Gates Carbon Drive System and the Rohloff SPEEDHUB 500/14 (Illustration 1) come together. At the time of delivery the Gates Carrier may already be fitted to the hub. If this is not the case, please follow the instructions for retrofitting the carrier to your hub. Illustration 1: Rohloff SPEEDHUB 500/14 with Gates-Rohloff Carrier M46x6 and Rear Sprocket M46x6 24
mounting Lubricate the inner thread of the Rear Sprocket M46x6 and carefully screw it on to the Carrier as far as possible by hand (illustration 3). As shown in illustration 3, the flange of the rear sprocket needs to be on the hub side. Make sure to bring the parts together in the right angle and do not cant them. Tighten the Rear Sprocket M46x6 with the POM- Sprocket-Key (Art. No. 10400001, 1040000X), to keep the sprocket and the Carrier from loosening from the hub in future mounting processes. To keep the hub from rotating while you thread on the carrier, you may hold the driver (sprocket thread) in place with the Rohloff Sprocket Tool and an Open-end Wrench SW24 (illustration5). Always make sure that the Rohloff Sprocket tool is seated correctly and secured in place. 2 Please note: Always secure the Sprocket tool, as described in the Rohloff Owners Manual (chapter Service, paragraph 3 „Sprocket reversing/replacing“), using a quick release skewer (CC versions), or an axle nut (TS versions), to avoid damage to the driver (sprocket thread). (Illustration 2). Illustration 2: Securing the Rohloff Sprocket tool with quick release skewer or axle nut Illustration 3: Rohloff SPEEDHUB 500/14 with Gates Rohloff Carrier M46x6 and Rear Sprocket M46x6 www.carbondrivesystems.com 25
Page 1 and 2: Manual for the Gates Carbon Drive S
Page 3 and 4: 1 first steps • Congratulations!
Page 5 and 6: first steps 1 Have your bike checke
Page 7 and 8: first steps 1 Mounting the tensione
Page 9 and 10: first steps 1 7. 8. 1. Drive belt n
Page 11 and 12: mounting Mounting the Gates Carbon
Page 13 and 14: mounting 2 Illustration 3: Correct
Page 15 and 16: mounting Checking the belt tension
Page 17 and 18: mounting Checking the belt tension
Page 19 and 20: mounting axle. If the Snubber is lo
Page 21 and 22: mounting 2 Shim ring for bottom bra
Page 23: mounting Mounting the Gates Carbon
Page 27 and 28: mounting Ensure that the surfaces o
Page 29 and 30: mounting Removing the Gates-Rohloff
Page 31 and 32: exchange When does the Gates Carbon
Page 33 and 34: exchange Profile Wear Gauge Illustr
Page 35 and 36: for Frame builders Frame requiremen
Page 37 and 38: 5 Gear Ratio Comparisum • Compari
Page 39 and 40: atio overview 19 Teeth rear 20 Teet
Page 41 and 42: atio overview Sprocket-size combina
Page 43: Find more information for Europe: U

General Information Gates/Rohloff - Koga Signature

Create successful ePaper yourself

Delete template?

Save as template?