Defence Aluminium – Plate Products - Aleris

Mechanical performance
Minimum mechanical properties
Alloy Temper Specifi cation* Test
direction
Plate thickness
mm in
Tensile strength Rm MPa ksi
Yield strength Rp0.2 MPa ksi
Elongation A
%
AA 5083 H131 MIL-DTL-46027 L 6.35 - 12.67 0.250 - 0.499 310 45.0 241 35.0 8
(table VI) 12.7 - 50.8 0.500 - 2.000 310 45.0 255 37.0 8
50.83 - 76.2 2.001 - 3.000 303 44.0 241 35.0 9
EN AW 5083 H131 TL 2350-0004 LT 6.35 - 12.67 0.250 - 0.499 311 45.0 242 35.0 8
12.7 - 50.8 0.500 - 2.000 311 45.0 256 37.0 8
50.83 - 76.2 2.001 - 3.000 304 44.0 242 35.0 9
AA 5059 H131 MIL-DTL-46027 L 6.35 - 12.67 0.250 - 0.499 393 57.0 303 44.0 8
Alustar ® (table VI) 12.7 - 50.8 0.500 - 2.000 393 57.0 296 43.0 7
50.83 - 76.2 2.001 - 3.000 344 50.0 289 42.0 8
EN AW 5059 H131
Alustar
TL 2350-0004 LT 6 - 60 0.236 - 2.362 370 54.0 300 44.0 8
®
AA 5059 H136 MIL-DTL-46027 L 6.35 - 12.67 0.250 - 0.499 365 53.0 296 43.0 10
Alustar ® (table VI) 12.7 - 50.8 0.500 - 2.000 358 52.0 289 42.0 10
50.83 - 76.2 2.001 - 3.000 344 50.0 289 42.0 10
AA 2519 T87 MIL-A-46192 L 12.7 - 38.1 0.500 - 1.500 455 66.0 407 59.0 10
(table II) 38.1 - 50.8 1.501 - 2.000 455 66.0 407 59.0 9
50.8 - 76.2 2.001 - 3.000 462 67.0 414 60.0 8
76.2 - 101.6 3.001 - 4.000 469 68.0 421 61.0 7
AA 7017 T6 TL 2350-0004 LT 6 - 50 0.236 - 1.969 430 62.4 360 52.2 8
> 50 - 76 > 1.969 - 2.992 410 59.5 340 49.3 8
> 76 > 2.992 410 59.5 340 49.3 6
EN AW 7020 T6 TL 2350-0004 LT < 25 < 0.984 350 50.8 280 40.6 10
> 25 - 60 > 0.984 - 2.362 340 49.3 275 40.0 8
AA 7039 T6 MIL-DTL-46063 L < 38.1 < 1.5 414 60.0 352 51.0 9
(table II) > 38.1 > 1.5 393 57.0 331 48.0 8
* Mechanical properties according to table VI of MIL-DTL-46027 for standard dimensions up to 60” x 140” (width x length)
For wider plates with dimensions 60” < width < 100” mechanical properties are guaranteed according to MIL-DTL-46027 table II
Other dimensions on request
Minimum and typical mechanical properties
are measured in L-direction
as specifi ed in MIL standards, while
plates produced according to TL standards
are tested in LT direction. Properties
after welding are always measured
across the weld seam, typically
in the LT direction.
6
Defence Aluminium