Manual - TP-Link

More documents

Recommendations

Info

time. • Static: When Static mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted. • Permanent: When Permanent mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be saved even the switch is rebooted. Status: Select Enable/Disable the Port Security feature for the port. Note: 1. The Port Security function is disabled for the LAG port member. Only the port is removed from the LAG, will the Port Security function be available for the port. 2. The Port Security function is disabled when the 802.1X function is enabled. 5.1.4 Port Isolation Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forward portlist. Choose the menu “Switching→Port→Port Isolation” to load the following page. Figure 5-5 Port Isolation Config The following entries are displayed on this screen: ‣ Port Isolation Config Port: Select the port number to set its forwardlist. 33
Forward Portlist: Select the port that to be forwarded to. ‣ Port Isolation List Port: Forward Portlist: Display the port number. Display the forwardlist. 5.2 LAG LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, so as to implement the traffic load sharing among the member ports in the group and to enhance the connection reliability. For the member ports in an aggregation group, their basic configuration must be the same. The basic configuration includes STP, QoS, GVRP, VLAN, port attributes, MAC Address Learning mode and other associated settings. The further explains are following: • If the ports, which are enabled for the GVRP, 802.1Q VLAN, Voice VLAN, STP, QoS, DHCP Snooping and Port Configuration (Speed and Duplex, Flow Control), are in a LAG, their configurations should be the same. • The ports, which are enabled for the Port Security, Port Mirror, MAC Address Filtering, Static MAC Address Binding and 802.1X Authentication, can not be added to the LAG. • It’s not suggested to add the ports with ARP Inspection and DoS Defend enabled to the LAG. If the LAG is needed, you are suggested to configure the LAG function here before configuring the other functions for the member ports. Tips: 1. Calculate the bandwidth for a LAG: If a LAG consists of the four ports in the speed of 1000Mbps Full Duplex, the whole bandwidth of the LAG is up to 8000Mbps (2000Mbps * 4) because the bandwidth of each member port is 2000Mbps counting the up-linked speed of 1000Mbps and the down-linked speed of 1000Mbps. 2. The traffic load of the LAG will be balanced among the ports according to the Aggregate Arithmetic. If the connections of one or several ports are broken, the traffic of these ports will be transmitted on the normal ports, so as to guarantee the connection reliability. Depending on different aggregation modes, aggregation groups fall into two types: Static LAG and LACP Config. The LAG function is implemented on the LAG Table, Static LAG and LACP Config configuration pages. 5.2.1 LAG Table On this page, you can view the information of the current LAG of the switch. Choose the menu Switching→LAG→LAG Table to load the following page. 34
Page 1 and 2: TL-SG3210 JetStream L2 Lite Managed
Page 3 and 4: CONTENTS Package Contents .........
Page 5 and 6: 7.4 STP Security...................
Page 7 and 8: 12.3.1 History Control ............
Page 9 and 10: Chapter 1 About this Guide This Use
Page 11 and 12: Chapter Chapter 9 QoS Chapter 10 AC
Page 13 and 14: Chapter 2 Introduction Thanks for c
Page 15 and 16: 2.3.2 Rear Panel The rear panel of
Page 17 and 18: Figure 3-3 Main Setup-Menu Note: Cl
Page 19 and 20: Indicates the SFP port is not conne
Page 21 and 22: Figure 4-5 System Time The followin
Page 23 and 24: Subnet Mask: Default Gateway: Enter
Page 25 and 26: 4.3 System Tools The System Tools f
Page 27 and 28: 4. After upgrading, the device will
Page 29 and 30: Session Timeout: If you do nothing
Page 31 and 32: information in a remote management
Page 33 and 34: Application Example 2 for SSH: ‣
Page 35 and 36: 5. After the public key and private
Page 37 and 38: selected, the port can forward the
Page 39: network information illegally. The
Page 43 and 44: Figure 5-7 Detail Information 5.2.2
Page 45 and 46: Figure 5-9 LACP Config The followin
Page 47 and 48: Port: Packets Rx: Packets Tx: Octet
Page 49 and 50: The address filtering feature allow
Page 51 and 52: VLAN ID: Port: Type: Aging Status:
Page 53 and 54: Figure 5-14 Dynamic Address The fol
Page 55 and 56: The following entries are displayed
Page 57 and 58: packets of different VLANs. The swi
Page 59 and 60: IEEE 802.1Q VLAN function is implem
Page 61 and 62: LAG: Displays the LAG to which the
Page 63 and 64: is bound to VLAN, the device can be
Page 65 and 66: DA and SA respectively refer to des
Page 67 and 68: 1. When receiving an untagged packe
Page 69 and 70: The following entries are displayed
Page 71 and 72: VLAN with its VLANID as 20, owning
Page 73 and 74: ‣ Configuration Procedure • Con
Page 75 and 76: and deregisters the attribute infor
Page 77 and 78: LeaveAll timer will start to begin
Page 79 and 80: port of switch C. Figure 7-1 Basic
Page 81 and 82: RSTP (Rapid Spanning Tree Protocol)
Page 83 and 84: Figure 7-3 Port roles The Spanning
Page 85 and 86: 4. If the TxHold Count parameter is
Page 87 and 88: Port Status: LAG: is the shortest p
Page 89 and 90: Priority: VLAN ID: Clear: Enter the
Page 91 and 92:
Step Operation Description 1 Make c
Page 93 and 94:
Figure 7-10 Port Protect The follow
Page 95 and 96:
1 Configure ports On VLAN→802.1Q
Page 97 and 98:
• For Instance 2 (VLAN 102, 104 a
Page 99 and 100:
1. Multicast IP Address: As specifi
Page 101 and 102:
The host, running IGMPv1, does not
Page 103 and 104:
Figure 8-5 Port Config The followin
Page 105 and 106:
VLAN ID: Router Port Time: Member P
Page 107 and 108:
Configuration procedure: Step Opera
Page 109 and 110:
8.2.1 Multicast IP Table On this pa
Page 111 and 112:
to restrict users ordering multicas
Page 113 and 114:
Max Groups: LAG: Specify the maximu
Page 115 and 116:
Chapter 9 QoS QoS (Quality of Servi
Page 117 and 118:
Figure 9-4 SP-Mode 2. WRR-Mode: Wei
Page 119 and 120:
Step Operation Description 1 Select
Page 121 and 122:
Figure 9-9 DSCP Priority The follow
Page 123 and 124:
Egress Rate(Kbps): LAG: Configure t
Page 125 and 126:
‣ Port Voice VLAN Mode 5 00-D0-1E
Page 127 and 128:
The following entries are displayed
Page 129 and 130:
‣ Create OUI OUI: Mask: Descripti
Page 131 and 132:
10.1.2 Time-Range Create On this pa
Page 133 and 134:
the performance of the switch. Pack
Page 135 and 136:
User Priority: Time-Range: Select t
Page 137 and 138:
IP ToS: IP Pre: Time-Range: Enter t
Page 139 and 140:
Select Policy: Select ACL: S-Mirror
Page 141 and 142:
Figure10-14 Bind the policy to the
Page 143 and 144:
3 Configure for requirement 2 and 4
Page 145 and 146:
The following entries are displayed
Page 147 and 148:
11.1.3 ARP Scanning ARP (Address Re
Page 149 and 150:
network configuration protocol opti
Page 151 and 152:
Option 82 can contain 255 sub-optio
Page 153 and 154:
messages that can be forwarded by t
Page 155 and 156:
Figure 11-10 ARP Attack - Cheating
Page 157 and 158:
Figure 11-12 Man-In-The-Middle Atta
Page 159 and 160:
Configuration Procedure: Step Opera
Page 161 and 162:
Auto Refresh: Refresh Interval: Ena
Page 163 and 164:
11.4 802.1X The 802.1X protocol was
Page 165 and 166:
2. Upon receiving the authenticatio
Page 167 and 168:
Figure 11-20 Global Config The foll
Page 169 and 170:
Control Mode: Control Type: Authori
Page 171 and 172:
Chapter 12 SNMP ‣ SNMP Overview S
Page 173 and 174:
management station. The specified U
Page 175 and 176:
12.1.3 SNMP Group On this page, you
Page 177 and 178:
Figure 12-6 SNMP User The following
Page 179 and 180:
• read-only: Management right of
Page 181 and 182:
Figure 12-8 Notification Config The
Page 183 and 184:
The RMON Groups can be configured o
Page 185 and 186:
Figure 12-11 Alarm Config The follo
Page 187 and 188:
Chapter 13 Cluster With the develop
Page 189 and 190:
Figure 13-2 Neighbor Information Th
Page 191 and 192:
13.1.3 NDP Config On this page you
Page 193 and 194:
Collect Topology: Click the Collect
Page 195 and 196:
NTDP: Select Enable/Disable NTDP fo
Page 197 and 198:
Figure 13-11 Cluster Summary for In
Page 199 and 200:
administrator manages all the switc
Page 201 and 202:
Chapter 14 Maintenance Maintenance
Page 203 and 204:
Figure 14-2 Memory Monitor Click th
Page 205 and 206:
14.2.2 Local Log Local Log is the l
Page 207 and 208:
The following entry is displayed on
Page 209 and 210:
Figure 14-9 Ping The following entr
Page 211 and 212:
Appendix A: Specifications IEEE802.
Page 213 and 214:
Figure B-2 5) The following TCP/IP
Page 215 and 216:
Appendix C: Load Software Using FTP
Page 217 and 218:
Figure C-4Select the port to connec
Page 219 and 220:
[TP-LINK] : start Start . . . . . .
Page 221 and 222:
Figure D-3 Welcome to the InstallSh
Page 223 and 224:
Figure D-7 InstallShield Wizard Com
Page 225 and 226:
Figure D-12 TP-LINK 802.1X Client E
Page 227 and 228:
FAQ: Q1: Why does this error dialog
Page 229 and 230:
GMRP allows network devices to regi
Page 231:
switch. Simple Network Management P
show all

Manual - TP-Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?