Download - Power-One

Certificate of Compliance
Certificate: 2262749 (LR 38879C) Master Contract: 173688
Project: 2262749 Date Issued: 2010/01/28
Issued to:
Power-One, Inc
740 Calle Plano
Camarillo, CA 93012
USA
Attention: Ms. Editha Vergara
The products listed below are eligible to bear the CSA
Mark shown with adjacent indicators 'C' and 'US' for
Canada and US or with adjacent indicator 'US' for
US only or without either indicator for Canada only.
Issued by:
Gwang-Yeol Park, Eng.
Gwang-Yeol Park, Eng.
PRODUCTS
CLASS 5311 11
CLASS 5311 91
- POWER SUPPLIES - Component Type(CSA 60950-1-07-2nd Ed)
- POWER SUPPLIES - Component Type(UL 60950-1-2nd Ed)Certified to
U.S.Stds
DC-DC Power Supply, Model 20/40 IMX (standard type) and KMX (custom type) series.
For details related to rating, size, configuration, etc., reference should be made to the CSA Certification Record
or the Descriptive Report.
Notes:
1. “G” suffix may be followed by a dash (-) and suffix letters and/or numbers denoting non-safety-critical
options (unless described otherwise in the report) such as, but not limited to, open frame, positive or negative
shut down, non-standard pin configuration, increased electric strength, etc.
2. Any combination of input voltage and output voltages shown above creates a valid model number.
3. In addition to model(s) listed above, following custom model number(s) may be used with the exact model
number listed below: Custom Model Designation: 40KMX35MMTH-S1. (Input Voltage Rating: 18-75 V dc;
48/60 V dc nominal. Output Ratings: 6V @ 1.97A, -7.3V @ 130mA, 7.3V @ 1.55A, 14V @ 30mA.)
CONDITIONS OF ACCEPTABILITY
1. All secondary output circuits are SELV and are not hazardous energy levels.
DQD 507 Rev. 2009-09-01

Certificate: 2262749 (LR 38879C) Master Contract: 173688
Project: 2262749 Date Issued: 2010/01/28
2. All models are intended to be supplied from an isolated secondary circuit.
3. The input/output connectors are not acceptable for field wiring and are only intended for connection to
mating connectors of the internal wiring inside the end-use product. The acceptability of these and the mating
connectors relative to secureness, insulation materials, and temperatures shall be considered.
4. A suitable Electrical, Fire and Mechanical enclosure shall be provided.
5. All models were submitted and tested for a maximum manufacturer’s recommended ambient
operating temperature of 110ºC for -8 models and 71ºC for -9 models, and 80ºC for 40KMX35MMTH-
S1, 40KMX35MMTH-S2 and 40KMX35MTTJ-S2 models. Consideration should be given to measure the
temperatures on the unit when the converter is installed in the end-use equipment.
6. The maximum working voltage present is 77 V rms, 150 V pk for Model 40IMX35D15D15-8Z, and
83 V rms, 212 V pk for model 40KMX35MMTH-S1. The Electric Strength Tests in the end product shall be
based on these values.
7. The units were tested for an input voltage range per the tables in the Nomenclature and Electrical
ratings section of this report with zero tolerance. If used outside these voltage ranges, additional testing may be
required.
8. Special enclosure consideration should be given to the end-use installation. Hazardous voltage
is available on the surface of the PWB. The end-use product should be reviewed to determine whether
accessibility requirements are met for the end-use product.
9. Special spacing consideration should be given to the end-use product as the spacings between the unit
and mounting surface have not been evaluated.
10. Abnormal and Component Failure Tests on all models except 20IMX35 and 20KMX35 were conducted
with the power supply input protected by certified fuse, rated F, 125 V dc, 5 A. If a fuse rated greater than 5 A
is used, additional testing may be required.
Component Failure test on models 20IMX35 and 20KMX35 were conducted with input protected by
certified fuse, rated 125 V dc, 8 A. If a fuse rated greater than 8 A is used and not certified, additional testing
may be required.
11. For the purpose of applying insulation requirements, the input to this DC to DC converter is identified as
TNV-2 or SELV, therefore, basic insulation based on 75 V dc input is provided between the input and output of
the converter. An additional evaluation is needed if the source is other than TNV-2 or SELV.
12. Model 40KMX35MTTJ-S2 has been evaluated for operational altitude of 4500 m. Per IEC60664-1:
1992 Table A.2. Altitude Correction Factor is 1.4 for the higher Altitude and not intended for use in vehicles, on
board ships or aircraft.
APPLICABLE REQUIREMENTS
CAN/CSA-C22.2 No 60950-1-07 - Information Technology Equipment - Safety - Part 1: General Requirements
ANSI/UL 60950-1, Second Edition - Information Technology Equipment - Safety - Part 1: General
Requirements
DQD 507 Rev. 2009-09-01

Descriptive Report
and Test Results
Edition 1:
January 28, 2010; Project 2262749 - Vancouver
Issued by Gwang-Yeol Park, Eng.
MASTER CONTRACT: 173688 (LR 38879C)
REPORT: 2262749
PROJECT: 2262749
Contents: Certificate of Compliance - Pages 1 to 2
Supplement to Certificate of Compliance - Page 1
Descriptive Report and Tests - Pages 1 to 8
Attachment 1 - List of Critical Components (4 pages)
Attachment 2 - Photographs (6 pages)
Attachment 3 - Schematics (21 pages) – Not for publication
(Engineering use only)
Bi-Nat CSA 60950-1-03/UL 60950-1 Design Manual, Rev. 2.2
PRODUCTS
CLASS 5311 11 - POWER SUPPLIES - Component Type (CSA 60950-1-07-2 nd Ed)
CLASS 5311 91 - POWER SUPPLIES - Component Type (UL 60950-1-2 nd Ed) - Certified to U.S. Standards
Component type power supplies intended for use with Information Technology and Business Equipment, where
the suitability of the combination is to be determined by CSA International.
DC-DC Power Supply, Model 20/40 IMX (standard type) and KMX (custom type) series; specified as follows:
Typical Model designation:
40 IMX 35 D05 D05 - 9Z
I II III IV V VI
I - Input Voltage Ratings: 20 = 09-36 V dc
40 = 18-75 V dc; 48/60 V dc nominal
II - Model Series: IMX or KMX
III - Maximum Output Power: 35 = 35 Watts
BI-NAT CSA 60950-1-03/UL 60950-1, 1 st Edition Rev. 2.2 DESIGN MANUAL (ISSUED WITH REPORT
2196792) IS AN INTEGRAL PART OF THIS REPORT
This report shall not be reproduced, except in full, without the approval of CSA International.
2262749 Report_2262749.doc\dw
DQD 507.10 Rev. 2008-11-28

MASTER CONTRACT: 173688 (LR 38879C)
REPORT: 2262749
PROJECT: 2262749
Page No: 2
Date Issued: January 28, 2010
IV - Output Voltage Rating:
V - Output Voltage rating:
1)
-03 = 3 Volts dc
1)
-05 = 5 Volts dc
2)
D05 = 5 Volts dc
2)
D12 = 12 Volts dc
2)
D15 = 15 Volts dc
3)
D05 = 5 Volts dc
3)
D12 = 12 Volts dc
3)
D15 = 15 Volts dc
VI - Options Suffix: (May Be Combined)
8 = -40 to 110ºC (Operating ambient temperature range)
9 = -40 to 71ºC (Operating ambient temperature range)
i = Inhibit
Z = Open Frame
1) - Output No. 1 for models with triple output.
2) - Output No. 1 and 4 for models with quad outputs.
3) - Output No. 2 and 3 for models with quad outputs.
Notes:
1. “G” suffix may be followed by a dash (-) and suffix letters and/or numbers denoting non-safety-critical
options (unless described otherwise in the report) such as, but not limited to, open frame, positive or
negative shut down, non-standard pin configuration, increased electric strength, etc.
2. Any combination of input voltage and output voltages shown above creates a valid model number.
3. In addition to model(s) listed above, following custom model number(s) may be used with the exact
model number listed below:
Custom Model Designation: 40KMX35MMTH-S1. (Input Voltage Rating: 18-75 V dc; 48/60 V dc
nominal. Output Ratings: 6V @ 1.97A, -7.3V @ 130mA, 7.3V @ 1.55A, 14V @ 30mA.)
APPLICABLE REQUIREMENTS
CAN/CSA-C22.2 No 60950-1-07 Information Technology Equipment - Safety - Part 1: General
Requirements
ANSI/UL 60950-1, Second Edition Information Technology Equipment - Safety - Part 1: General
Requirements
CONDITIONS OF ACCEPTABILITY
1. All secondary output circuits are SELV and are not hazardous energy levels.
2. All models are intended to be supplied from an isolated secondary circuit.
3. The input/output connectors are not acceptable for field wiring and are only intended for connection to
mating connectors of the internal wiring inside the end-use product. The acceptability of these and the
mating connectors relative to secureness, insulation materials, and temperatures shall be considered.
2262749 Report_2262749.doc\dw
DQD 507.10 Rev. 2008-11-28

MASTER CONTRACT: 173688 (LR 38879C)
REPORT: 2262749
PROJECT: 2262749
Page No: 3
Date Issued: January 28, 2010
4. A suitable Electrical, Fire and Mechanical enclosure shall be provided.
5. All models were submitted and tested for a maximum manufacturer’s recommended ambient operating
temperature of 110ºC for -8 models and 71ºC for -9 models, and 80ºC for 40KMX35MMTH-S1,
40KMX35MMTH-S2 and 40KMX35MTTJ-S2 models. Consideration should be given to measure the
temperatures on the unit when the converter is installed in the end-use equipment.
6. The maximum working voltage present is 77 V rms, 150 V pk for Model 40IMX35D15D15-8Z, and
83 V rms, 212 V pk for model 40KMX35MMTH-S1. The Electric Strength Tests in the end product shall
be based on these values.
7. The units were tested for an input voltage range per the tables in the Nomenclature and Electrical ratings
section of this report with zero tolerance. If used outside these voltage ranges, additional testing may be
required.
8. Special enclosure consideration should be given to the end-use installation. Hazardous voltage is
available on the surface of the PWB. The end-use product should be reviewed to determine whether
accessibility requirements are met for the end-use product.
9. Special spacing consideration should be given to the end-use product as the spacings between the unit and
mounting surface have not been evaluated.
10. Abnormal and Component Failure Tests on all models except 20IMX35 and 20KMX35 were conducted
with the power supply input protected by certified fuse, rated F, 125 V dc, 5 A. If a fuse rated greater
than 5 A is used, additional testing may be required.
Component Failure test on models 20IMX35 and 20KMX35 were conducted with input protected by
certified fuse, rated 125 V dc, 8 A. If a fuse rated greater than 8 A is used and not certified, additional
testing may be required.
11. For the purpose of applying insulation requirements, the input to this DC to DC converter is identified as
TNV-2 or SELV, therefore, basic insulation based on 75 V dc input is provided between the input and
output of the converter. An additional evaluation is needed if the source is other than TNV-2 or SELV.
12. Model 40KMX35MTTJ-S2 has been evaluated for operational altitude of 4500 m. Per IEC60664-1: 1992
Table A.2. Altitude Correction Factor is 1.4 for the higher Altitude and not intended for use in vehicles,
on board ships or aircraft.
MARKINGS
Marking Method:
- CSA accepted and UL recognized adhesive nameplate, suitable for the surface to which it is applied.
Marking consists of Company Name and Series identification etched in PWB trace patterns.
- Due to insufficient surface to which a CSA Mark can be applied after all other necessary markings have
been applied (i.e. free, markable surface less than 1 cm 2 ), the CSA Mark may be applied to the smallest
unit of packaging containing the certified product.
Note: Refer to the Design Manual for other marking option.
2262749 Report_2262749.doc\dw
DQD 507.10 Rev. 2008-11-28

Declaration of Conformity
CE MARKING
We, Power-One, Inc.,740 Calle Plano, Camarillo, CA. 93012 USA
declare under our sole responsibility that the products;
Power Supply Model:
IMX35, KMX35 Series
to which this declaration relates, is/are in compliance with the following document(s):
Quality Standard(s): ISO 9001, EN 29001
Directive:
DIR 2006/95/EC, Low Voltage Directive
Product Safety Standard(s): EN 60950-1: 2006
IEC 60950-1: 2005
(Licensed by a Notified Body to the European Union )
These component level power supplies are intended exclusively for inclusion within other
equipment by an industrial assembly operation or by professional installers per the
Installation Instructions provided with the power supplies.
Camarillo, Ca. June 29, 2010
(Manufacturer) (Place) (Date)
Robert P. White Jr.
Director of Safety and
Environmental Compliance