Trevira CS 100 - NozzFlow - Air Distribution
Trevira CS 100 - NozzFlow - Air Distribution
Trevira CS 100 - NozzFlow - Air Distribution
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Specification: Fabric<strong>Air</strong> ® <strong>Trevira</strong> <strong>CS</strong> <strong>100</strong> – <strong>NozzFlow</strong><br />
Division 15, Section 15800<br />
2005 Master Spec Format (Section/Category): 23 37 16<br />
PART 2 - PRODUCTS<br />
2.1 MANUFACTURER<br />
a. Manufacturer must comply with all previous described requirements. Approved manufacturers:<br />
1. Fabric<strong>Air</strong>, Inc.<br />
312-A Swanson Drive<br />
Lawrenceville, GA 30043<br />
Phone: (502) 493 2210<br />
Fax: (502) 493 4002<br />
E-mail: @fabricair.<br />
2.2 FABRIC AIR DISPERSION SYSTEM<br />
a. Fabricair Dispersion System shall be constructed of Fabric<strong>Air</strong> ® <strong>Trevira</strong> <strong>CS</strong> <strong>100</strong> fabric. The fabric is a<br />
woven fire retardant and permeable fabric complying with the following characteristics:<br />
1. Fabric: <strong>100</strong>% Permanent Flame Retardant Polyester<br />
2. Weight: 7.2 oz./yd² per ASTM D3776<br />
3. Shrinkage: Max. 0,5% per DIN EN 26 630<br />
4. Color: <strong>100</strong>0 white. <strong>100</strong>1 Blue, <strong>100</strong>2 Orange, <strong>100</strong>3 Gray, <strong>100</strong>4 Black, <strong>100</strong>5 Red or custom<br />
5. Temperature Range: -40°F to +140°F<br />
6. Permeabilities: per design: 2,11,18,36 or 66 (+/- 5%) per ASTM D737, Frazier – calandering of<br />
fabric NOT accepted<br />
7. Fire Retardancy: Must meet the requirements in NFPA 90-A, ICC AC167 and UL 2518<br />
b. SYSTEMS FABRICATION REQUIREMENTS<br />
1. <strong>Air</strong> dispersion accomplished by using conical aerodynamic nozzles. Diameter of nozzles to be<br />
¾” – height to be minimum ½”. Due to exact requirements of throw and maximum level of noise<br />
alternative flow models are not acceptable.<br />
2. Color of nozzles must match color of fabric. Unless otherwise specifically mentioned on<br />
drawings or otherwise in this specification suppliers standard table is used for selection of color.<br />
3. Location and number of nozzles to be specified and approved by manufacturer<br />
4. The system is made of permeable fabric. Permeability of fabric must be reached based on<br />
weave construction only and weave must have gone through thermo fixation in order to secure<br />
same permeability after wash. Fabric with permeability obtained based on calandering is not<br />
accepted.<br />
5. Fibers used must be permanently fire retardant – fire-reducing treatments are not accepted.<br />
6. Provide system in sections optimized for maintenance, connected by zippers. Zippers must<br />
provide closure completely around the circumference to prevent leakage. Required number of<br />
zippers as specified by manufacturer.<br />
7. Each section to have a unique tag including information about: manufacturers order number,<br />
position, diameter of section, length of section, maintenance instruction, code compliance and<br />
contact details for spare parts.<br />
8. Fabric system shall include connectors to attach to suspension system listed below.<br />
Fabric<strong>Air</strong> ® <strong>Trevira</strong> <strong>CS</strong> <strong>100</strong> - <strong>NozzFlow</strong> Last up-date: 06/2011<br />
Specification guidelines for Fabric<strong>Air</strong> ® products – subject to change without further notice. Page 2 of 5<br />
For more information, contact: Fabric<strong>Air</strong>, Inc.: info@fabricair.com or Phone: (502) 493 2210
Change language