SMAC Applications Book - ORLIN Technologies Ltd

More documents

Recommendations

Info

SMAC 05 Connector Pin Insertion No bent pins 100% inspection Programmable for different sizes OPERATION ¥ Pick up pin, locate hole ¥ Set force, press in ¥ Set lower force, drive in, check depth ¥ Report good / bad / missing pin Actuator: LAL-50 Stroke (mm): 100 Resolution: 1 or 5 micron Force: 25 newtons Moving Mass: 225 gms Supply Voltage: 24 Volts Key Operational Details: Pick up pin, set low force, target top of hole to locate it,if alignment is no good, pin will not reach target position If alignment is good, set full force, drive in, measure penetration To check for missing pin, set lower force, attempt to drive in further,if pin exists, there should be no movement SMAC Advantages: Force can be selected in position servo mode Position can be measured to 5 microns Motion profile can be selected for different size pins Assembly machine can be readily reconfigured for many types of connectors PICK 10 mm PLACE 5 mm SMAC •5807 Van Allen Way •Carlsbad, California 92008•Fax: (760) 929-7588 •Tel: (760) 929-7575 0 mm 0 20 40 60 80 100 120 140 160 180 Pick at One Level - Place at Second Level
SMAC 06 Disk Drive Assembly ¥ High volume (millions per month) ¥ Low prices (short assembly times) ¥ Very high reliability (strict process control) Other Applications: Press fit for motor hub -check part size, check final part position Press fit spacer & hub to secure disk platters -check part size, check final part position Load and secure read-head comb assembly -check part size, orientation, -check final part position 50 5 FORCE (newtons) Weight of moving mass Ð.25 2.25 FORCE is proportional to current CURRENT (amps) Actuator: LAL-150 Stroke (mm): 15 Resolution: 1 or 5 micron Force: 200 newtons Moving Mass: 350 gms Supply Voltage: 48 Volts Key Operational Details: Pick & Place motor hub, check part size, check final part position Pick & Place spacer to secure disk platters SMAC Advantages: Multi-position moves to secure each platter Soft landing capability to protect surface finishes Control final part position to within 10 microns SMAC •5807 Van Allen Way •Carlsbad, California 92008•Fax: (760) 929-7588 •Tel: (760) 929-7575
Page 1 and 2: SMAC INDEX # 01 02 03 04 05 06 07 0
Page 3 and 4: SMAC PERFORMANCE 01 04 05 06 12 19
Page 5 and 6: SMAC MOVING COIL TECHNOLOGY SOFT LA
Page 7 and 8: SMAC 02 Chip Mounter Pick, place at
Page 9: SMAC 04 Die Bonding A. PICK UP B. O
Page 13 and 14: SMAC 08 Spot Welding, Soldering Hig
Page 15 and 16: SMAC 10 Medical Assembly Medical de
Page 17 and 18: SMAC 12 Glass Cutting Glass cutter
Page 19 and 20: SMAC 14 Stacking of Components Actu
Page 21 and 22: SMAC 16 0.040 mm .1 degree 25 mm Hi
Page 23 and 24: SMAC 18 Hot Cathode for TV Tubes Su
Page 25 and 26: SMAC 20 Wafer Transport Wafers are
Page 27 and 28: SMAC 22 2-Axis Robot ¥ Pick up bad
Page 29 and 30: SMAC 24 Picking Test Tubes From Rac
Page 31 and 32: SMAC 26 Sandblasting Surgical Needl
Page 33 and 34: SMAC 28 Precision Elevators Bags ar
Page 35 and 36: SMAC 30 TV Tube Inspection Better p
Page 37 and 38: SMAC 32 Lead Inspection Machine To
Page 39 and 40: SMAC 34 Soft Contact Lens Mold Each
Page 41 and 42: SMAC 36 Screw Thread Checking 1. SM
Page 43 and 44: SMAC 38 Internal Diameter Check Als
Page 45 and 46: SMAC 40 Switch Testing SMAC actuato
Page 47 and 48: SMAC 42 Actuator: LAR-30 Screw Adju
Page 49 and 50: SMAC 44 Medical Materials Testing A
Page 51 and 52: SMAC 46 Simulating Impact Damage on
Page 53 and 54: SMAC 48 Glue Dot Dispensing Placeme
Page 55 and 56: SMAC 50 X-Y ¥ High speed, high res
Page 57 and 58: SMAC 52 CHIP CIRCUIT BOARD CONDUCTI
Page 59 and 60: SMAC 54 Checking & Reworking Contac
Page 61 and 62:
SMAC 56 LAL-30 Part to be Assembled
Page 63 and 64:
SMAC 58 Spot Welding Welding: Ball
Page 65 and 66:
SMAC 60 ORIENT PART CAMERA Precisio
Page 67 and 68:
SMAC 62 Changing shot profiles in s
show all

SMAC Applications Book - ORLIN Technologies Ltd

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?