SMAC Applications Book - ORLIN Technologies Ltd

More documents

Recommendations

Info

SMAC 57 LAL-90 Checking Pre-loading of Precision Linear Guides Preloading of precision linear guides balances the load to maintain the designed four point contact structure. This makes the guides suitable for applications with minimum vibration. Material damage from rolling contact fatigue is also minimized. The typical preload is 2 % of the static load rating of the linear guide so each model uses a different preload. SMAC actuators can be used to measure the deflection of the slide unit as a prescribed force is applied to check the preload. A single fixture built using an SMAC actuator can check different models. Actuator: LAL-90 Stroke (mm): 15, 50 Resolution: 1 or 5 micron Force: 100 newtons Moving Mass: 250 gms Supply Voltage: 48 Volts Key Operational Details: Softland on slide unit, register initial position, ramp force up to prescribed value, measure deflection Compare deflection with allowable parameter, indicate good/bad part Force can be controlled to +/- 25 grams Position can be maintained to +/- 1 encoder counts SMAC Advantages: Instantaneous transition from position mode to force mode Ability to monitor position in force mode Force can be varied from 0 to 100 newtons in small increments SMAC •5807 Van Allen Way •Carlsbad, California 92008•Fax: (760) 929-7588 •Tel: (760) 929-7575
SMAC 58 Spot Welding Welding: Ball to Pen Nib Light Bulb Filament Tab to Pacemaker Battery Contact Wire to Motor Brush Actuator: LAL-30 Stroke (mm): 15, 25 Resolution: 1 or 5 micron Force: 10 newtons Moving Mass: 150 gms Supply Voltage: 24 Volts Key Operational Details: High speed approach, slow down, soft land on surface Ramp force up to set value, weld (solder) part to surface SMAC Advantages: SMAC Soft Landing profile uses a high speed approach to save time Force is ramped up to desired value to hold part in place to get a good weld SMAC •5807 Van Allen Way •Carlsbad, California 92008•Fax: (760) 929-7588 •Tel: (760) 929-7575
Page 1 and 2:
SMAC INDEX # 01 02 03 04 05 06 07 0
Page 3 and 4:
SMAC PERFORMANCE 01 04 05 06 12 19
Page 5 and 6:
SMAC MOVING COIL TECHNOLOGY SOFT LA
Page 7 and 8:
SMAC 02 Chip Mounter Pick, place at
Page 9 and 10:
SMAC 04 Die Bonding A. PICK UP B. O
Page 11 and 12: SMAC 06 Disk Drive Assembly ¥ High
Page 13 and 14: SMAC 08 Spot Welding, Soldering Hig
Page 15 and 16: SMAC 10 Medical Assembly Medical de
Page 17 and 18: SMAC 12 Glass Cutting Glass cutter
Page 19 and 20: SMAC 14 Stacking of Components Actu
Page 21 and 22: SMAC 16 0.040 mm .1 degree 25 mm Hi
Page 23 and 24: SMAC 18 Hot Cathode for TV Tubes Su
Page 25 and 26: SMAC 20 Wafer Transport Wafers are
Page 27 and 28: SMAC 22 2-Axis Robot ¥ Pick up bad
Page 29 and 30: SMAC 24 Picking Test Tubes From Rac
Page 31 and 32: SMAC 26 Sandblasting Surgical Needl
Page 33 and 34: SMAC 28 Precision Elevators Bags ar
Page 35 and 36: SMAC 30 TV Tube Inspection Better p
Page 37 and 38: SMAC 32 Lead Inspection Machine To
Page 39 and 40: SMAC 34 Soft Contact Lens Mold Each
Page 41 and 42: SMAC 36 Screw Thread Checking 1. SM
Page 43 and 44: SMAC 38 Internal Diameter Check Als
Page 45 and 46: SMAC 40 Switch Testing SMAC actuato
Page 47 and 48: SMAC 42 Actuator: LAR-30 Screw Adju
Page 49 and 50: SMAC 44 Medical Materials Testing A
Page 51 and 52: SMAC 46 Simulating Impact Damage on
Page 53 and 54: SMAC 48 Glue Dot Dispensing Placeme
Page 55 and 56: SMAC 50 X-Y ¥ High speed, high res
Page 57 and 58: SMAC 52 CHIP CIRCUIT BOARD CONDUCTI
Page 59 and 60: SMAC 54 Checking & Reworking Contac
Page 61: SMAC 56 LAL-30 Part to be Assembled
Page 65 and 66: SMAC 60 ORIENT PART CAMERA Precisio
Page 67 and 68: SMAC 62 Changing shot profiles in s
show all

SMAC Applications Book - ORLIN Technologies Ltd

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?