Kenwood TK-7180 - KO4BB's Home Page

More documents

Recommendations

Info

TK-7180 INSTALLATION 3. Horn Alert/P.A. Relay Unit (KAP-2 : Option) The Horn alert (max. 2A drive), Public address and External speaker function are enabled by installing the KAP-2 in the TK-7180 transceiver. 3-1. Installing the KAP-2 unit in the transceiver 1. Remove the cabinet, top packing and shielding plate of the transceiver. 2. Set the KAP-2 relay unit jumper pins according to the purpose of use. 3. Remove the 6-pin jumper connector inserted in the TX-RX unit (B/3) connector (CN428). ( q ) 4. Insert one side of the lead wire with connector (E37-1114- 05) into the relay unit connector (CN3) ( w ) and the other side into the TX-RX unit (B/3) connector (CN428) ( e ). 5. Place the relay unit at the position shown in Figure 3-2 and secure it to the chassis with a screw. 6. Remove the cap on the rear of the chassis by pushing it from the inside with your finger. ( r ) 7. Pass the 6-pin connector of the cable (E37-1113-05) through the chassis hole ( t ) and insert the bush into the chassis hole. 8. Rotate the bush of the cable 90 degrees counterclockwise as viewed from the rear of the chassis. ( y ) 9. Insert the 6-pin connector of the cable into the connector (CN2) of the KAP-2 relay unit. ( u ) Note : You must setup using the KPG-89D. E37-1114-05 w CN3 CN428 q CN428 e r Fig. 3-1 Fig. 3-2 Fig. 3-3 y t CN2 u E37-1113-05 Fig. 3-4 8
INSTALLATION TK-7180 4. Control Head Remote Kit (KRK-10 : Option) The KRK-10 remote kit is used to remotely operate a TK- 7180 transceiver. 4-1. Installing the KRK-10 kit to the transceiver 1. Remove the front panel from the transceiver. 2. Install the KRK-10 main panel onto the transceiver. 3. Install the KRK-10 rear panel onto the front panel. 4. Connect the KRK-10 main panel to the rear panel with the cable. ■ Remove the front panel from the transceiver 1. Lift the two tabs of the panel on the bottom of the transceiver with a flat-head screwdriver ( q ) and remove the panel from the chassis ( w ). Note : Confirm that the tabs of the speaker hardware fixture and holder is securely fitted in the front panel. 2. Remove the flat cable from the connector (CN902) of the display unit of the panel. ( e ) 3. Fold the black line of the flat cable (in three parts) as shown in Figure 4-2. ( r, t, y ) ■ Install the KRK-10 main panel onto the transceiver 4. Insert the flat cable that was removed in step 2 above into the connector (CN1) of the interface unit (A/2) of the KRK- 10 main panel (A62-1101-01). ( u ) Note : The terminal side of the flat cable must face down when inserting the flat cable into the connector. 5. Fit the main panel with four tabs onto the front of the chassis. ( i ) Note : When installing the main panel onto the front of the chassis, hold down the flat cable with your fingers to prevent it from being caught. i KRK-10 main panel u CN1 CN902 Fig. 4-3 e w q ■ Install the KRK-10 rear panel onto the front panel 6. Insert the flat cable attached to the interface unit (B/2) of the KRK-10 rear panel (A82-0056-01) into the connector (CN902) of the display unit of the panel ( o ). (The flat cable has been pre-inserted in the connector (CN2) of the rear panel at the time of shipping.) Note : The terminal side of the flat cable must face down when inserting the flat cable into the connector. 7. Fit the four tabs of the rear panel into the front panel. ( !0 ) CN902 o Chassis side r Fig. 4-1 CN2 KRK-10 rear panel y t r t y !0 Panel side Fig. 4-2 Fig. 4-4 9
Page 1 and 2: VHF FM TRANSCEIVER TK-7180 SERVICE
Page 3 and 4: GENERAL / SYSTEM SET-UP TK-7180 SER
Page 5 and 6: REALIGNMENT TK-7180 5-2. Connection
Page 7: INSTALLATION TK-7180 1. Ignition Se
Page 11 and 12: INSTALLATION TK-7180 6. Voice Scram
Page 13 and 14: DISASSEMBLY FOR REPAIR TK-7180 1. P
Page 15 and 16: DISASSEMBLY FOR REPAIR TK-7180 ■
Page 17 and 18: CIRCUIT DESCRIPTION TK-7180 2-5. Sq
Page 19 and 20: CIRCUIT DESCRIPTION TK-7180 6. Powe
Page 21 and 22: SEMICONDUCTOR DATA TK-7180 Micropro
Page 23 and 24: COMPONENTS DESCRIPTION TK-7180 Ref.
Page 25 and 26: Ref. No. Address New Parts No. Desc
Page 27 and 28: PARTS LIST TK-7180 Ref. No. Address
Page 33 and 34: EXPLODED VIEW TK-7180 A A : N09-240
Page 35 and 36: ADJUSTMENT TK-7180 Controls Power s
Page 37 and 38: ADJUSTMENT TK-7180 ■ Flow chart N
Page 39 and 40: Common Section Item Condition 1. Se
Page 41 and 42: ADJUSTMENT TK-7180 Item Condition T
Page 43 and 44: Item Condition Testequipment ADJUST
Page 45 and 46: ADJUSTMENT TK-7180 Item Condition T
Page 47 and 48: TERMINAL FUNCTION TK-7180 Pin No. N
Page 49 and 50: TERMINAL FUNCTION TK-7180 Pin No. N
Page 51 and 52: J K L M N O P Q R S PC BOARD TK-718
Page 53 and 54: 1 TK-7180 PC BOARD A B C D E F G H
Page 55 and 56: 54 J I H G F E D C B A 1 2 3 4 5 6
Page 57 and 58: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GN
Page 59 and 60:
57 J K L M N O P Q R S 1 2 3 4 5 6
Page 61 and 62:
58 TK-7180 SCHEMATIC DIAGRAM 7 6 5
Page 63 and 64:
-t C906 0.01u C917 0.1u C918 10u10
Page 65 and 66:
61 SCHEMATIC DIAGRAM TK-7180 J I H
Page 67 and 68:
63 SCHEMATIC DIAGRAM TK-7180 T S R
Page 69 and 70:
65 SCHEMATIC DIAGRAM TK-7180 AD AC
Page 71 and 72:
67 SCHEMATIC DIAGRAM TK-7180 AN AM
Page 73 and 74:
+ - - + + - - + -t -t E TO DISPLAY
Page 75 and 76:
70 AGC MIC AMP MI2 IC414 TC75W51FU
Page 77 and 78:
TK-7180 LEVEL DIAGRAM Receiver Sect
Page 79 and 80:
TK-7180 OPTIONAL ACCESSORIES: KRK-1
Page 81 and 82:
Page 83 and 84:
Page 85:
TK-7180 SPECIFICATIONS GENERAL Freq
show all

Kenwood TK-7180 - KO4BB's Home Page

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?