IBC Marketing Brochure - Evapco

from
IBC Compliant Designs for…
C O O L I N G T O W E R S
CLOSED CIRCUIT COOLERS
Independently Certified
for ALL Geographic
Locations and Installations

Beichuan, China – Earthquake, May 2008
Biloxi, Mississippi USA – Hurricane Katrina, August 2005
Contact your local EVAPCO Sales Representative or
EVAPCO World Headquarters for more information.
The New and Improved Advanced Technology (AT) Design for Cooling Towers and Closed
Circuit Coolers is Available in two Configurations to Meet Your IBC Needs for ALL
Geographic Locations and Installations:
• STANDARD — Compliant up to 1g or 60 psf wind loads
• UPGRADED CONSTRUCTION — Compliant up to 5.12g or 145 psf wind loads

What is IBC?
International Building Code
The International Building Code (IBC) is a comprehensive set of regulations addressing both the structural
design and the installation requirements for building systems — including HVAC and industrial refrigeration
equipment. The IBC replaces BOCA’s The National Building Code, ICBO’s Uniform Building Code and SBCCI’s
Standard Building Code.
Compared to previous building codes that considered only the building structure and component anchorage,
the requirements contained within the IBC address anchorage, structural integrity, and the operational
ability of a component following either a seismic or wind load event.
Simply stated, the IBC code provisions require that evaporative cooling equipment, and all other components
permanently installed on a structure, must be designed to meet the same seismic and wind load forces as the
building to which they are attached.
Seismic Design
The required seismic design factors include:
• Occupancy Category
• Site Classification
• Spectral Response Acceleration (S s )
• Amplification Factor (a p )
• Importance Factor (I p )
• Response Modification Factor (R p )
• Installation Elevation (Z/h)
The project architect or civil engineer is responsible for
determining these factors to be used for the building design. A
mechanical consulting engineer and/or design build contractor
will then apply these factors to a series of charts and graphs to
determine the appropriate seismic design factors based on the
location of the installation and ultimately the “importance” of
the facility.
A chart of the potential seismic activity in the United States is
shown below. Buildings constructed in the red, orange and
yellow areas of the map are most likely to require an upgraded
IBC seismic construction design.
Seismic Map
Courtesy US Geological
Survey Website
Wind Load
Map Courtesy
IBC 2006 Text
Wind Design
The required wind force design factors include:
• Basic Wind Speed (3-second gust)
• Structure Classification
• Exposure Category
• Structure Elevation
The IBC 2006 code includes a map of basic wind speed (3-second
gust) by contour line. However, local regulations may be more
stringent than the published speeds.
Whichever design force — seismic or wind — is more
severe for the building governs the design of the building
and all attached equipment.
Design Implementation
EVAPCO applies the seismic and wind load design information
provided for the project to determine the equipment design
necessary to meet IBC requirements. This process ensures that the
mechanical equipment and its components are compliant per the
provisions of the International Building Code as given in the plans
and specifications for the project.
AT Cooling Towers & ATW Closed Circuit Coolers
are now Independently Certified to withstand
seismic and wind loads
in ALL geographic locations and installations
in accordance with the International Building Code (IBC 2006)

The AT and ATW lines of induced draft counterflow Cooling Towers and Closed Circuit Coolers reflect
EVAPCO’s commitment to product development. The NEW owner oriented features of the AT and
ATW, along with the independent certification of IBC compliance reinforce EVAPCO’s position as the
premier supplier of evaporative cooling equipment to the HVAC industry.
Efficient Drift
Eliminators
• Advanced design
removes mist from the
leaving airstream.
• Made from corrosion
resistant PVC for long life.
CLOSED CIRCUIT COOLERS
PVC Spray Distribution
System with ZM Nozzles
on ATW Closed Circuit
Coolers
• Nozzles are threaded into
header at proper orientation.
• Large orifice fixed position
nozzles prevent clogging.
• Threaded end caps for ease of
cleaning.
Most Accessible
Basin
• Access from all four
sides and ends.
• Large open area
simplifies
maintenance.
• Basin may be
inspected with
pumps running.
Seismic and Wind Load Certification
AT, USS, UAT, UT Cooling Towers
ATC-E Evaporative Condensers
ATW Closed Circuit Coolers
Units Designed and Manufactured to Meet the
Seismic & Wind Load Requirements of:
IBC 2006 ASCE-7 NFPA 5000
Independent Certification By:
IBC Serial Number: 43387
15-226PA
NEW IBC
Certification Label
• Provided with every unit
to indicate independent
certification and
compliance.
Optional Pulse-Pure® Water Treatment System*
The AT and ATW are available with Evapco’s optional Pulse~Pure® non-chemical
water treatment system. The Pulse~Pure® Water Treatment System utilizes pulsed-power
technology to provide CHEMICAL FREE Water Treatment. The Pulse~Pure® system delivers
short, high-frequency bursts of low energy electromagnetic fields to the recirculating water
in the AT or ATW and will:
• Control bacteria to levels well below traditional chemical water treatment.
• Control the formation of mineral scale.
• Save water by operating at higher cycles of concentration.
• Yield corrosion rates equivalent to chemical water treatment.
*Note factory mounting of Evapco’s Pulse~Pure®
system is only available on closed circuit cooler
products.
Improved WST Inlet Louvers*
(Water and Sight Tight)
• Easily removable for access.
• Improved design to keep sunlight out — preventing
biological growth.
• Keeps water in
while keeping
dirt and debris
out.
*Patent Pending

®
All accessories shown here are available on both
AT & ATW Products unless otherwise specified.
Super Low Sound Fan
• Extremely wide chord,
forward swept fan blades for
sound sensitive applications.
• One piece molded heavy duty
FRP construction.
• 9-15 dB(A) sound reduction.
C O O L I N G T O W E R S
Unique Fan Drive System
• All normal maintenance
can be performed
quickly from outside
the unit!
• Extended lube lines are
standard.
• Five (5) year motor and
drive warranty.
• Non-corroding cast aluminum sheaves.
• Heavy-duty fan shaft bearings with L-10 life of 75,000 -
135,000 hrs.
• All other components constructed of corrosion resistant
materials.
• Totally enclosed fan motors assure long life.
PVC Spray Distribution System with
EvapJet Nozzles on AT Cooling Towers
• Non-corrosive PVC
construction with new
EvapJet nozzles.
• Large 1" wide orifice
nozzles prevent clogging
and are threaded for easy
removal and positive
positioning.
• 66% fewer nozzles!
• System branches have threaded end caps to assist with
debris removal.
NEW Independent Certification for
IBC Compliance
As required by the International Building Code, EVAPCO
supplies a certificate of compliance as part of its submittal
documents. The certificate of
compliance demonstrates that
the equipment has been
Certificate of Compliance
independently tested and
ESWA Closed Circuit Coolers
Are certified to meet or exceed the Seismic and Wind Load Provisions
set forth in the applicable building codes for this project. analyzed in accordance with
These products have been manufactured following all
applicable quality assurance programs.
the IBC seismic and wind load
Applicable Building Codes:
Referenced Report:
IBC 2006
VMA-43387
ASCE-7
NFPA 5000
Approval Agency:
VMC Seismic Consulting Group
requirements.
EVAPCO...Specialists in Heat Transfer Products and Services. ESWA IBC COC 001
NEW Easy-Rig Field Seam*
• Eliminates up to 66% of
fasteners
• The new field assembly seam
design ensures easier assembly
and fewer field seam leaks.
• Self-guiding channels guide
the casing section into position
improving the quality of the
field seam.
*Patent Pending
NEW Easy-Access Louver Door
• Hinged Access Panel with Quick Release
Mechanism.
• Allows easy access to perform routine
maintenance and inspection of the makeup
assembly, strainer screen and basin.
• Louver access door is standard on models
with 5 and 6 ft. louver sizes.

®
EVAPCO PRODUCTS ARE MANUFACTURED WORLDWIDE.
World Headquarters/
Research and
Development Center
EVAPCO Facilities
EVAPCO, Inc. — World Headquarters & Research/Development Center
EVAPCO, Inc. • P.O. Box 1300 • Westminster, MD 21158 USA
PHONE: 410-756-2600 • FAX: 410-756-6450 • E-MAIL: marketing@evapco.com
EVAPCO North America
EVAPCO Europe
EVAPCO Asia/Pacific
EVAPCO, Inc.
World Headquarters
P.O. Box 1300
Westminster, MD 21158 USA
Phone: 410-756-2600
Fax: 410-756-6450
E-mail: marketing@evapco.com
EVAPCO East
5151 Allendale Lane
Taneytown, MD 21787 USA
Phone: 410-756-2600
Fax: 410-756-6450
E-mail: marketing@evapco.com
EVAPCO Midwest
1723 York Road
Greenup, IL 62428 USA
Phone: 217-923-3431
Fax: 217-923-3300
E-mail: evapcomw@evapcomw.com
EVAPCO West
1900 West Almond Avenue
Madera, CA 93637 USA
Phone: 559-673-2207
Fax: 559-673-2378
E-mail: contact@evapcowest.com
EVAPCO Iowa
925 Quality Drive
Lake View, IA 51450 USA
Phone: 712-657-3223
Fax: 712-657-3226
EVAPCO Iowa
Sales & Engineering
1234 Brady Boulevard
Owatonna, MN 55060 USA
Phone: 507-446-8005
Fax: 507-446-8239
E-mail: evapcomn@evapcomn.com
Refrigeration Valves &
Systems Corporation
A wholly owned subsidiary of EVAPCO, Inc.
1520 Crosswind Dr.
Bryan, TX 77808 USA
Phone: 979-778-0095
Fax: 979-778-0030
E-mail: rvs@rvscorp.com
McCormack Coil Company, Inc.
A wholly owned subsidiary of EVAPCO, Inc.
P.O. Box 1727
6333 S.W. Lakeview Boulevard
Lake Oswego, OR 97035 USA
Phone: 503-639-2137
Fax: 503-639-1800
E-mail: mail@mmccoil.com
EvapTech, Inc.
A wholly owned subsidiary of EVAPCO, Inc.
8331 Nieman Road
Lenexa, KS 66214 USA
Phone: 913-322-5165
Fax: 913-322-5166
E-mail: marketing@evaptechinc.com
Tower Components, Inc.
A wholly owned subsidiary of EVAPCO, Inc.
5960 US HWY 64E
Ramseur, NC 27316
Phone: 336-824-2102
Fax: 336-824-2190
E-mail: mail@towercomponentsinc.com
EVAPCO Newton
701 East Jourdan Street
Newton, IL 62448 USA
Phone: 618-783-3433
Fax: 618-783-3499
E-mail: evapcomw@evapcomw.com
EVAPCO Europe, N.V.
European Headquarters
Industrieterrein Oost 4010
3700 Tongeren, Belgium
Phone: (32) 12-395029
Fax: (32) 12-238527
E-mail: evapco.europe@evapco.be
EVAPCO Europe, S.r.l.
Via Ciro Menotti 10
I-20017 Passirana di Rho
Milan, Italy
Phone: (39) 02-939-9041
Fax: (39) 02-935-00840
E-mail: evapcoeurope@evapco.it
EVAPCO Europe, S.r.l.
Via Dosso 2
23020 Piateda Sondrio, Italy
EVAPCO Europe, GmbH
Bovert 22
D-40670 Meerbusch, Germany
Phone: (49) 2159-69560
Fax: (49) 2159-695611
E-mail: info@evapco.de
EVAPCO S.A. (Pty.) Ltd.
A licensed manufacturer of Evapco, Inc.
18 Quality Road
Isando 1600
Republic of South Africa
Phone: (27) 11 392-6630
Fax: (27) 11-392-6615
E-mail: evapco@evapco.co.za
Tiba Engineering Industries Co.
A licensed manufacturer of Evapco, Inc.
5 Al Nasr Road St.
Nasr City, Cairo, Egypt
Phone: (20) 2-290-7483/(20) 2-291-3610
Fax: (20) 2-404-4667/ (20) 2-290-0892
E-mail: manzgroup@tedata.net.eg
EVAPCO Asia/Pacific Headquarters
1159 Luoning Rd. Baoshan Industrial Zone
Shanghai, P. R. China, Postal Code: 200949
Phone: (86) 21-6687-7786
Fax: (86) 21-6687-7008
E-mail: marketing@evapcochina.com
Evapco (Shanghai) Refrigeration
Equipment Co., Ltd.
1159 Louning Rd., Baoshan Industrial Zone
Shanghai, P.R. China, Postal Code: 200949
Phone: (86) 21-6687-7786
Fax: (86) 21-6687-7008
E-mail: marketing@evapcochina.com
Beijing EVAPCO Refrigeration
Equipment Co., Ltd.
Yan Qi Industrial Development District
Huai Rou County
Beijing, P.R. China, Postal Code: 101407
Phone: (86) 10 6166-7238
Fax: (86) 10 6166-7395
E-mail: evapcobj@evapcochina.com
Aqua-Cool Towers (Pty.) Ltd.
A licensed manufacturer of Evapco, Inc.
34-42 Melbourne St.
P.O. Box 436
Riverstone, N.S.W. Australia 2765
Phone: (61) 29 627-3322
Fax: (61) 29 627-1715
E-mail: sales@aquacoolingtowers.com.au
EvapTech Asia Pacific Sdn. Bhd
A wholly owned subsidiary of EvapTech, Inc.
IOI Business Park, 2/F Unit 21
Persiaran Puchong Jaya Selatan
Bandar Puchong Jaya,
47170 Puchong, Selangor, Malaysia
Phone: +(60-3) 8070 7255
Fax: +(60-3) 8070 5731
E-mail: marketing@evaptechinc.com
EVAPCO...SPECIALISTS IN HEAT TRANSFER PRODUCTS AND SERVICES.
Visit EVAPCO’s Website at: http://www.evapco.com
©2008 EVAPCO, Inc. Printed on FSC Certified Paper — 25% PCW / Printed with Soy Based Inks Bulletin IBC01