Part 2 - SAE

TIME
Thursday, May 21 - Morning
Technical and Business Sessions
Tires (NVC202)
SESSION TITLE, DESCRIPTION, AND ROOM
Salon V
This session includes papers regarding
vehicle exterior or interior tire/pavement
noise.
10:00 a.m. - 12:00 p.m.
Organizers:
Paul R. Donavan, Illingworth & Rodkin Inc.;
Richard F. Schumacher, RS Beratung LLC;
Saeed Siavoshani, Dow Automotive
Salon VI
Windnoise and Aeroacoustics
(NVC701)
This session is to present numerical and
experimental work pertaining to noise
due to flow around the vehicle body, such
as flow-induced interior noise, flow over
protrusions, sunroofs, windows, noise from
ventilation systems, or flow noise in exhaust
system. Papers on aerodynamics alone
without sound are excluded. Numerical
studies may include new models or models
based on existing theory as long as they are
adequately supported by experimental or
theoretical verifications.
10:00 a.m. - 12:00 p.m.
Organizers:
Luc Mongeau, McGill Univ.; Robert E.
Powell, Exa Corp.
Technical and Business Sessions
TIME SESSION TITLE, DESCRIPTION, AND ROOM
10:01
p.m.
10:02
p.m.
Written Only (NVC999)
Written Only Papers
Application of Noise Control and Heat Insulation Materials
and Devices in the Automotive Industry (Written Only -- No
Oral Presentation)
(951375)
Timothy Hirabayashi, General Motors Corp.; David J.
McCaa, Certain-Teed Products Corp; Bob Rebandt, Ford
Motor Co; Phillip A. Rusch, Harley-Davidson Inc; Pranab
Saha, Kolano & Saha Engineers Inc;
Recent Advances in Powertrain Sound Quality Hardware
Tuning Devices and Perspectives on Future Advances
(Written Only -- No Oral Presentation)
(2009-01-2192)
Garry Dunne, Jaguar Cars, Ltd.
10:00
a.m.
10:20
a.m.
10:40
a.m.
11:00
a.m.
11:20
a.m.
11:40
a.m.
Modeling and Experimental Investigation of
Tire Cavity Noise Generation Mechanisms
for a Rolling Tire
(2009-01-2104) (2009-01-2237)
Frank Feng, Univ of Missouri; Perry Gu;
Yongjian Chen, Zongbao Li, Ford Motor
Co.
A Three-Dimensional Ring-Based Structural
Tyre Model: Development and Validation
(2009-01-2105) (2009-01-2236)
Peter Kindt, Filip De Coninck, Paul Sas,
Wim Desmet, Katholieke Universiteit Leuven
Investigation of Tire Road Noise with
Special Consideration for Airborne Noise
Transmission
Aero-Acoustic Predictions of Automotive
Instrument Panel Ducts
Stephane Détry, Visteon Interior Systems;
Yves Detandt, Diego d’Udekem, Julien
Manera, Free Field Technologies
Numerical Simulations and Measurements
of Mirror-Induced Wind Noise
David J. Lepley, Nissan Technical Center
North America Inc.; Tony Frazer, Brüel
& Kjær North America Inc; Sivapalan
Senthooran, Dena Hendriana, Exa Corp.
Correlated Beamforming Method
for Relevant Aeroacoustic Sources
Identification
(2009-01-2109) (2009-01-2234)
Gregor Koners, Daimler AG
Jean-luc Adam, Denis Ricot, Renault SAS;
arnaud menoret, Christophe lambourg,
Signal Developpement
A Comparison of Fiber Wheel Liners on Two
Different Vehicles
(2009-01-2106) (2009-01-2235)
Barry Wyerman, Janesville Acoustics;
Gabriella Cerrato Jay, Eric Frank, Sound
Answers Inc.
Use of the ASTM Standard Reference Test
Tire as a Benchmark for On-Bound Tire/
Pavement Noise Measurement
A Note on Equilibrium Turbulent Boundary
Layer Wall Pressure Models
Teresa Miller, Mark Moeller, Spirit
AeroSystems Inc
(2009-01-2108) (2009-01-2233)
Paul R. Donavan, Illingworth & Rodkin Inc.;
Dana M. Lodico, Lodico Acoustics LLC
Prediction of the Spindle Force Using
Measured Road Force on Rolling Tire
Investigation of Gap Deflector Efficiency for
Reduction of Sunroof Buffeting
Bernd Crouse, Ganapathi Balasubramanian,
Sivapalan Senthooran, David Freed, Exa
Corporation; Kang-Duck Ih, Hyundai Motor
Co; Seong Ryong Shin, Hyundai Motor Co
& KIA Motors Corp
Effects of Notches on Surface Pressure
Fluctuations Downstream of a Leading
Edge Spoiler
(2009-01-2107) (2009-01-2238)
Masami Matsubara, Doshisha Univ. Jong Beom Park, McGill Univ.; Paloma
Mejia, Purdue Univ.; Luc Mongeau, McGill
Univ.
SAE International
J A N
F O U N D E D
U A R
Y
9
1
0
5
Announcing,
SAE International
Journal of Materials
& Manufacturing
The SAE International Journal of Materials
& Manufacturing focuses on publishing the
most authoritative and in-depth technical
research papers in areas related to all types of
materials and
manufacturing techniques for automotive and aerospace
engineering technologies. Research and application areas
include Ferrous and Non-Ferrous Materials, Powdered
Metals, Ceramics, Plastics, Polymers, Casting,
Stamping, Forming, Welding and Joining, Design for
Manufacturability, Fatigue, and Life Cycle Assessment.
In addition to being identified as some of the best published
work at SAE International, these papers as a set have long-term
reference to the engineering community and to society at-large.
The journal is available in print and online formats.
SAE International is partnering with HighWire Press to
produce the online journal.
Print Format Online Format
ISSN 1946-3979 1946-3987
SAE Member $225.60 $270.93
Nonmember $282.00 $338.66
Product Code V117-5 V117-5EJ
For more information and to view table of contents,
go to www.sae.org/journals.
Order today!
Online: store.sae.org
E-mail: CustomerSales@sae.org
Phone: 1-888-875-3976 (U.S. & Canada)
or 724-772-4086 (outside U.S. & Canada)
P90578
2009 SAE Government/Industry Meeting 39