Husqvarna - AR19 - JW Hire & Sales Ltd

More documents

Recommendations

Info

LUBRICATION Checking the engine’s oil level. Make sure that the machine is parked on even ground with the engine stopped when checking the oil level. 1. Unscrew the dipstick and wipe it using paper towel or a lint-free rag. 2. Replace the dipstick without screwing it in. Remove and check the level on the dipstick. 3. Fill oil as necessary to the lip of the dipstick hole. Oil type, see chapter ”Lubrication/1. Engine oil”. 8011-020 4. Check that the rubber gasket is in position and screw the dipstick back into place. Do not tighten it askew or too hard or you may damage the threads. 2. Oil change in reduction gear 1:6 The engine’s reduction axle does not have a drainage screw, but the oil can be drained through the level plug hole (2) by tipping the machine forward. Because it is difficult to avoid spilling gasoline and releasing gasoline fumes, the oil should not be changed indoors. 1. Empty the fuel tank or put a vessel in place to collect gasoline spills. 2. Tip the machine forwards, place a vessel under the level plug (2) and remove the filler plug (1) and the level plug (2) 3. Allow the engine oil to drain into the vessel, right the machine and park it on even ground. 4. Refill using new oil of the same type as that in the engine in the filler hole until it runs over from the level plug. Volume 0.15 liters. 5. Replace the level and filler plugs. Tighten them moderately. 6. Wipe up any spilled oil. Checking the gearbox oil level Make sure the machine is parked on even ground and that the engine is not running. Carefully remove the level plug (2) and check that oil drains out. If there is no oil leakage, the machine can be carefully tipped forward to estimate the oil level. If necessary, fill the oil in the filler plug hole (1) until it runs over from the level plug. Replace the level and filler plugs. Tighten moderately. 8011-055 IMPORTANT INFORMATION Used engine oil is a health hazard and legislation prohibits disposal on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location. Avoid skin contact; wash with soap and water in case of spills. 40 – English
3. Chain Lubricate the chain so that it travels easily without binding. It is easiest to access with the drive guard cover dismounted. Use 30W engine oil or chainsaw oil or chain spray for motorcycles. LUBRICATION 8011-132 4. Rear wheels Applies to model <strong>AR19</strong>. Lubricate both rear wheels with a grease gun in the single nipple on the outside of the rear wheels until the grease begins to squeeze out. 8011-176 5. Tines Cover the tines with a thin coat of oil to avoid rust. This is particularly important prior to winter storage or if the machine will not be used for a period of longer than 30 days. 8011-286 6. Links and joints It is important to lubricate all links and joints so that they do not bind. Use 30W engine oil. 8011-270 English – 41
Page 1: Operator´s manual AR19 AR25 Please
Page 4 and 5: Congratulations INTRODUCTION Thank
Page 6 and 7: SYMBOLS AND DECALS WARNING! Xxxx xx
Page 8 and 9: SAFETY INSTRUCTIONS General The obj
Page 10 and 11: SAFETY INSTRUCTIONS Preparations
Page 12 and 13: SAFETY INSTRUCTIONS • Smoking, op
Page 14 and 15: SAFETY INSTRUCTIONS Maintenance •
Page 16 and 17: PRESENTATION Engine Exterior engine
Page 18 and 19: PRESENTATION Spark plug The engine
Page 20 and 21: Controls on the handle Rear wheel c
Page 22 and 23: Starting the engine Check that all
Page 24 and 25: RUNNING Aeration tips Should I wate
Page 26 and 27: MAINTENANCE Maintenance schedule Th
Page 28 and 29: MAINTENANCE Cleaning the sludge res
Page 30 and 31: MAINTENANCE Ignition system The eng
Page 32 and 33: Replacing and adjusting the drive b
Page 34 and 35: MAINTENANCE Wheels Replacing the dr
Page 36 and 37: MAINTENANCE Tines and tine shaft Re
Page 38 and 39: MAINTENANCE Chain Replacing the cha
Page 40 and 41: LUBRICATION Lubrication schedule 80
Page 44 and 45: 7. Adjustment for rear wheel depth/
Page 46 and 47: ASSEMBLY INSTRUCTIONS Applies to mo
Page 48 and 49: WIRING DIAGRAM 8011-099 8011-050 1.
Page 50 and 51: TECHNICAL DATA Engine unit AR19 AR2
Page 52 and 53: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 54 and 55: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 56: ´+H"r6=¨ 114 00 28-26 2001W35

Husqvarna - AR19 - JW Hire & Sales Ltd

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?