Thermoelectric Module Product Selection Guide - Ferrotec

ferrotec

Thermoelectric Module Product Selection Guide - Ferrotec

Thermoelectric Modules

PRODUCT SELECTION GUIDE


INTRODUCTION

Principles of Operation

A practical thermoelectric module generally consists of two or more elements of n and p-type doped semiconductor

material that are connected electrically in series and thermally in parallel. These thermoelectric elements and their

electrical interconnects typically are mounted between two ceramic substrates. A variety of different shapes, substrate

materials, metallization patterns and mounting options are available.

The schematic diagram above shows a typical thermoelectric module assembly. Both N-type and P-type Bismuth

Telluride thermoelectric materials are used in a thermoelectric cooler. This arrangement causes heat to move

through the module in one direction only while the electrical current moves back and forth alternately between the

top and bottom substrates through each N and P element. N-type material is doped so that it will have an excess of

electrons and P-type material is doped so that it will have a deficiency of electrons. The extra electrons in the N

material and the “holes” resulting from the deficiency of electrons in the P material are the carriers which move the

heat energy through the thermoelectric material. Most thermoelectric cooling modules are fabricated with an equal

number of N-type and P-type elements where one N and P element pair form a thermoelectric “couple.” For example,

the module illustrated above has two pairs of N and P elements and is termed a “two-couple module”.

Cooling capacity (heat actively pumped through the thermoelectric module) is proportional to the magnitude of the

applied DC electric current and the thermal conditions on each side of the module. By varying the input current

from zero to maximum, it is possible to regulate the heat flow and control the surface temperature.

Advantages of Thermoelectric Modules

■ No moving parts

■ Small and lightweight

■ Maintenance-free

■ Acoustically silent and electrically “quiet”

■ Heating and cooling with the same module (including temperature cycling)

■ Wide operating temperature range

■ Highly precise temperature control (to within 0.1°C)

■ Operation in any orientation, zero gravity and high G- levels

■ Environmentally friendly

■ Sub-ambient cooling

■ Cooling to very low temperatures (-80°C)

2


APPLICATIONS

Electronics Cooling

Electronics package cooling

Integrated circuit coolers

Lasers and Telecommunications

Laser diode coolers

Precision device cooling (lasers, microprocessors etc.)

Automotive

Climate controlled seats

Medical / Biomedical / Pharmaceutical

Thermal cycling devices (e.g. PCR Cyclers and blood analyzers)

Laboratory cold plates

Tissue preparation and storage

Dewpoint hygrometers

Electrophoresis cell coolers

Cold chambers

Constant temperature baths

Semiconductor

Silicon wafer cooling

Wafer thermal characterization

Instrumentation, Sensors and Detectors

Charge Coupled Device (CCD) Cooling

Charge Induced Device (CID) cooling

Infrared detectors

Thermal Management

Compact heat exchangers

Immersion coolers

Space Cooling

Small portable and stationary refrigeration

Wine and beverage coolers

Food coolers

Aerospace / Military / Defense

Infrared seeking missiles

Thermal viewers

Night vision equipment

Thermal weapons sights

Power Generation

Remote power systems

Consumer appliances (insect control)

3


H

TEC TEC NUMBERING SYSTEM SYSTEM

The following symbols are used in the tables:

Imax = Maximum input current in amperes

Qmax = Maximum heat pumping capacity in watts at DT = 0

Vmax = Maximum DC input voltage in volts at Imax and DTmax with Th = 50°C

DTmax = Maximum temperature differential in °C at a zero heat load (Q = 0)

W

H

Type 1 Type 2

L1

Multistage Type 1 — “CASCADE”

W1

6300 / 127 / 060AX

1. 2. 3. 4. 5. 6. 7.

1. Product Line

63 = 150°C Maximum temperature

95 = 200°C Maximum temperature

2. Shape

0 = Standard module

1 = Undesignated

2 = 2 stage module

3 = 3 stage module

3. Classification number

0 = Standard module

1 = Small size module

2 = Miniature module

3 = Modules configured

for laser diode applications

4 = High current module

4. Number of couples

5. Maximum current

0.1 Ampere increments

L2

L1

W2

H

W

H

W1

L2

4

L1

Multistage Type 2

L2

6. Substrate specification

A. Standard tolerance—plain ceramic surface

(lapped)

■ Miniature module

(+0.15mm height tolerance)

■ Standard module

(+0.25mm height tolerance)

■ 2 stage module

(+0.35mm height tolerance)

B. Tight tolerance – plain ceramic surface (precision

lapped)

■ Miniature module (No specification)

■ Standard module

(+0.025mm height tolerance)

■ 2 stage module

(+0.25mm height tolerance)

H. Solderable metalized ceramic on

hot side external surface

M. Solderable metalized ceramic on

both hot and cold side external surface

7. Options

S = RTV seal

L1

W2

Type 2 thermoelectric modules feature

a “porch” for easy attachment of leads.

This makes the L2 dimension slightly

longer than the L1 dimension. Please

call for exact L2 measurements for the

modules that you are interested in.

MATERIALS AND

SPECIFICATIONS

ARE SUBJECT

TO CHANGE

WITHOUT NOTICE.


Thermoelectric Module Product Selection Guide

Single Stage Modules

1.2A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150°C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/007/012 9500/007/012 1.2 0.6 0.9 70 1 4.01 4.01 2.33

6300/018/012 9500/018/012 1.2 1.6 2.5 70 2 6.05 6.05 7.62 2.59

6302/031/012 9502/031/012 1.2 2.8 4.3 70 1 7.98 7.98 2.08

6302/065/012

1.8A Models

9502/065/012 1.2 5.8 8.9 70 1 12.10 11.20 2.59

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/007/018 9500/007/018 1.8 0.9 0.9 70 1 4.01 4.01 2.03

6300/018/018 9500/018/018 1.8 2.4 2.5 70 2 6.05 6.05 7.62 2.28

6302/023/018 9502/023/018 1.8 3.1 3.2 70 1 6.05 7.98 1.77

6302/029/018 9502/029/018 1.8 3.9 4.0 70 1 6.05 9.91 1.77

6302/031/018 9502/031/018 1.8 4.1 4.3 70 1 7.98 7.98 1.77

6302/065/018

3.0A Models

9502/065/018 1.8 8.7 8.9 70 1 12.10 11.20 2.28

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6301/017/030 9501/017/030 3.0 3.8 2.3 72 1 11.50 11.50 3.18

6301/023/030 9501/023/030 3.0 5.2 3.2 72 1 7.39 22.40 3.18

6301/031/030 9501/031/030 3.0 7.0 4.3 72 1 15.10 15.10 3.18

6301/071/030 9501/071/030 3.0 16.0 9.8 72 1 22.4 22.40 3.18

6301/127/030

4.0A Models

9501/127/030 3.0 29.0 17.5 72 1 29.7 29.70 3.94

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/017/040 9500/017/040 4.0 5.1 2.3 72 1 15.01 15.10 4.16

6301/017/040 9501/017/040 4.0 5.1 2.3 72 1 11.50 11.50 3.18

6301/023/040 9501/023/040 4.0 6.9 3.2 72 1 7.39 22.40 3.18

6300/031/040 9500/031/040 4.0 9.3 4.3 72 1 20.00 20.00 4.16

6301/031/040 9501/031/040 4.0 9.3 4.3 72 1 15.10 15.10 3.18

6301/033/040 9501/033/040 4.0 4.8 4.5 72 1 15.90 22.40 3.37

6300/035/040 9500/035/040 4.0 10.0 4.8 72 1 15.10 29.80 4.16

6300/071/040 9500/071/040 4.0 21.0 9.8 72 1 29.80 29.80 4.16

6301/071/040 9501/071/040 4.0 21.0 9.8 72 1 22.40 22.40 3.18

6300/127/040 9500/127/040 4.0 38.0 17.5 72 1 39.70 39.70 4.16

6301/127/040 9501/127/040 4.0 38.0 17.5 72 1 29.70 29.70 3.94

Tabulated specifications are derived from the average performance of actual modules operating

in ambient air at sea level. Temperature differential is the difference in temperature between two copper plates attached

to the hot and cold module face plate using zinc-oxide-loaded silicone grease at the plate-to-module interfaces.

Products available from stock. For other products please call for delivery information.

5


Thermoelectric Module Product Selection Guide

Single Stage Modules

6.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/017/060 9500/017/060 6.0 7.6 2.3 72 1 15.10 15.10 4.16

6300/031/060 9500/031/060 6.0 14.0 4.3 72 1 20.00 20.00 4.16

6300/035/060 9500/035/060 6.0 16.0 4.8 72 1 15.10 29.80 4.16

6300/071/060 9500/071/060 6.0 32.0 9.8 72 1 29.80 29.80 4.16

6300/127/060 9500/127/060 6.0 57.0 17.5 72 1 39.70 39.70 4.16

6301/127/060 9501/127/060 6.0 57.0 17.5 72 1 29.70 29.70 3.61

6300/128/060

8.5A Models

9500/128/060 6.0 57.0 17.6 72 2 39.70 39.70 42.80 4.16

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/017/085 9500/017/085 8.5 11.0 2.3 72 1 15.10 15.10 3.94

6300/031/085 9500/031/085 8.5 20.0 4.3 72 1 20.00 20.00 3.94

6300/035/085 9500/035/085 8.5 22.0 4.8 72 1 15.10 29.80 3.94

6300/063/085 9500/063/085 8.5 40.0 8.7 72 1 39.70 39.70 3.94

6300/071/085 9500/071/085 8.5 45.0 9.8 72 1 29.80 29.80 3.94

6300/127/085 9500/127/085 8.5 80.0 17.5 72 1 39.70 39.70 3.94

6300/128/085 9500/128/085 8.5 80.0 17.6 72 2 39.70 39.70 42.8 3.94

9.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/031/090 9500/031/090 9.0 22.0 4.3 72 1 29.80 29.80 4.65

10.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6301/063/100 9501/063/100 10.0 47.0 8.7 72 1 20.10 39.70 3.64

6301/127/100 9500/127/100 10.0 95.0 17.5 72 1 39.70 39.70 3.64

12.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6304/071/120 9504/071/120 12.0 63.0 9.8 72 1 40.10 40.10 4.65

15.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6300/031/150 9500/031/150 15.0 35.0 4.3 72 1 29.80 29.80 4.60

6304/071/150 9504/071/150 15.0 79.0 9.8 72 1 40.10 40.10 4.65

24.0A Models

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6304/031/240 9504/031/240 24.0 55.0 4.3 72 1 39.70 39.70 4.62

6


Thermoelectric Module Product Selection Guide

High Power Modules

TE MODULE NUMBER Imax Qmax Vmax DTmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C)s W L1 L2 H

6305/071/240 9505/071/240 24.0 127.0 9.8 72 1 59.00 59.00 3.90

6300/090/300 9500/090/300 30.0 202.0 12.4 72 2 46.00 83.00 87.50 4.62

630X/127/150 950X/127/150 15.0 142.0 17.5 72 1 40.00 40.00 3.45

630X/131/150 950X/131/150 15.0 147.0 18.0 72 1 30.00 60.00 3.45

6300/180/085 9500/180/085 8.5 114.0 24.8 72 2 38.50 60.00 65.00 3.94

6300/241/060 9500/241/060 6.0 108.0 33.1 72 1 55.00 55.00 4.16

Miniature Modules for Laser Diode and Optoelectronics Applications

TE MODULE NUMBER Imax Qmax Vmax Dtmax Type DIMENSIONS (mm)

200° C (A) (W) (V) (°C)s W L1 L2 H

9503/018/012M 1.2 1.6 2.5 70 2 6.05 6.20 7.19 1.64

9503/018/018M 1.8 2.4 2.5 70 2 6.05 6.20 7.19 1.64

9503/023/018M 1.8 3.1 3.2 70 1 6.05 8.18 1.64

9503/029/018M 1.8 3.9 4.0 70 1 6.05 10.20 1.64

9503/031/018M 1.8 4.1 4.3 70 1 7.98 7.98 1.64

9503/035/018M 1.8 4.7 4.8 70 1 6.05 12.20 1.64

9503/018/020M 2.0 2.6 2.5 70 2 6.05 6.20 7.19 1.64

9503/035/025M 2.5 6.5 4.8 70 1 6.05 12.20 1.64

Modules with Center Holes

TE MODULE NUMBER Imax Qmax Vmax Dtmax Type DIMENSIONS (mm)

200° C (A) (W) (V) (°C)s W L H Hole Dia.

9506/023/030B 3.0 5.2 3.2 72 1 15.10 15.10 3.18 6.7

9506/023/040B 4.0 6.9 3.2 72 1 15.10 15.10 3.18 5.0

9504/023/040B 4.0 6.9 3.2 72 1 18.0 18.0 3.18 8.0

9500/125/060B

Long Life Modules

6.0 56.0 17.2 72 1 39.70 39.70 3.80 4.7

TE MODULE NUMBER Imax Qmax Vmax Dtmax Type DIMENSIONS (mm)

150° C (A) (W) (V) (°C)s W L1 L2 H

7001/127/040B 4.0 34.0 17.5 72 1 39.70 39.70 3.94

7000/127/060B 6.0 51.0 17.5 72 1 39.70 39.70 4.16

7000/127/085B 8.5 72.0 17.5 72 1 39.70 39.70 3.94

7000/031/150B 15.0 31.0 4.3 72 1 29.80 29.80 4.60

7004/071/150B 15.0 71.0 9.8 72 1 40.10 40.10 4.65

2 Stage Modules (Mulitstage)

TE MODULE NUMBER Imax Qmax Vma Dtmax Type DIMENSIONS (mm)

150° C 200° C (A) (W) (V) (°C) W1 L1 W2 L2 H

6320/157/035 9520/157/035 3.5 11.0 18.2 106 1 20.00 20.00 39.6 39.60 7.39

6320/185/065 9520/185/065 6.5 37.0 17.9 95 1 29.80 29.80 39.7 39.70 6.99

6320/157/070 9520/157/070 7.0 24.0 17.3 106 1 20.00 20.00 39.7 39.70 6.99

6320/094/230 9520/094/230 24.0 74.0 8.2 88 2 45.20 54.10 45.2 45.10 7.49

6320/118/080 9520/118/080 8.0 21.0 12.8 106 1 15.00 20.00 30.00 40.00 6.40

6320/197/080 9520/197/080 8.0 52.0 17.8 91 1 29.80 29.80 39.70 39.70 6.45

3 Stage Modules (Mulitstage)

TE MODULE NUMBER Imax Qmax Vma Dtmax Type DIMENSIONS (mm)

200° C (A) (W) (V) (°C) W1 L1 W2 L2 W3 L3 H

6330/119/045M 4.5 9.7 8.6 111.0 1 15.20 15.20 20.00 20.00 29.80 29.80 9.20

6330/228/045M 4.5 18.0 16.4 111.0 1 20.00 20.00 29.80 29.80 39.70 39.70 9.82

7


YOUR LOCAL DISTRIBUTOR

© All material copyright of Ferrotec Corporation

Version: 092001

SALES LOCATIONS

USA______________________________

Ferrotec (USA) Corporation

40 Simon Street

Nashua

NH-03060-3075

USA

Tel: (603) 883 9800

Fax: (603) 883 2308

http://www.ferrotec.com

info@ferrotec.com

GERMANY (EUROPEAN HEADQUARTERS) ____

Ferrotec GmbH

Hohes Gestade 14

72622 Nürtingen

Germany

Tel: +49 7022 9270 0

Fax: +49 7022 9270 10

http://www.ferrotec.com

gmbh@ferrotec.com

UNITED KINGDOM AND IRELAND __________

Ferrotec (UK) Ltd.

Talisman Business Centre

Bicester

Oxon. OX26 6HR

United Kingdom

Tel: +44 1869 363200

Fax: +44 1869 363201

http://www.ferrotec.com

info@ferrotec.co.uk

CORPORATE HEADQUARTERS

Ferrotec Corporation

1-4-14 Kyobashi

Chuo-ku

Tokyo 104-0031

Japan

http://www.ferrotec.co.jp

More magazines by this user
Similar magazines