Element II - Area Brochure - Visionaire Lighting, LLC

Housing
• The fixture housing is heavy-duty, extruded aluminum, with
heat radiating fins. A perforated aluminum top cover, beneath
a protective debris guard, protects the heat radiating fins
from contaminants and directs constant air flow over them for
maximum cooling.
Thermal Management
• The Element II provides excellent overall thermal management
by maximizing the fixture’s heat sink efficiency. This enables the
Element II to withstand higher ambient temperatures and drive
currents without degrading LED life. The Element II has a low
thermal resistance rating. The heat radiating fins and perforated
fixture components create superior thermal management results.
• The L70 test determines the point in an LEDs life when it reaches
70 percent of its initial output. Element II series LEDs have been
determined to last 150,000+ hours in 40 o C environments when
driven at 350 mA. See LED Data Chart for additional test results.
Optical System
• The highest lumen output LEDs available are utilized in the
Element II series. IES Types III and V distributions are standard.
The LED VisionBar TM light assemblies come in multiples of 24
(minimum 24 to maximum 288 LEDs) and are field replaceable.
The optical system qualifies as IES full cutoff; and is Dark-Sky
certified to restrict light trespass, glare and light pollution.
Quali-Guard ® Finish
• A Quali-Guard ® thermoset polyester powder coat painted finish
is available in white and custom colors.
Mounting - Area
•BOA- The cast aluminum Bolt-on Arm is shipped mounted to
the fixture. A pole plate is supplied for mounting to the pole; which
allows for quick and easy fixture installation with two set screws.
•WM- Galvanized steel wall mount bracket can be secured
directly to recessed junction box or the wall. The fixture is supplied
with a shortened arm bracket to keep the fixture closer to the wall.
•CM- Steel ceiling mount bracket can be secured directly to
recessed junction box, or to the ceiling. The housing hanger
bracket allows fixture to be suspended from ceiling bracket while
making wiring connection. The housing bracket then attaches
to the ceiling bracket via a tool-less latch. A tamper-proof screw
can then secure the bracket.
•KM- Knuckle Mount will mount over a 2⅜” horizontal or vertical
tenon and is field adjustable in increments of 5°
•MAF- Mast arm fitter is provided with a cast aluminum arm
adaptor designed to slip fit over a 1¼” to 2” horizontal tenon
(mast arm) and is adjustable +/- 5 degrees for fixture leveling.
EPA Data
Fixture
with Arm
EL2-S
EL2-1
.6
.7
.8
.9
1.3
1.3
1.1
1.2
1.1
1.2
1.1
1.2
An internal clamping device provides a secure attachment to the
mast arm, eliminating the need to drill for thru-bolt attachment.
•EBOA- End Mount version utilizing the same Quick Mount pole
adaptor for a bolt-on application
•EMAF- End Mount Mast Arm Fitter is provided with a cast
aluminum arm adaptor designed to slip fit over a 2” horizontal
tenon (mast arm) and is fully adjustable.
A round pole plate adaptor is required for mounting to a 3”- 6”
round pole.
Mounting - Roadway
• The Element II - Roadway is provided with a cast aluminum
arm adaptor designed to slip fit over a 1¼” to 2⅜” horizontal tenon
(mast arm) and is adjustable +/- 5 degrees for fixture leveling.
An internal clamping device provides a secure attachment to the
mast arm, eliminating the need to drill for thru-bolt attachment.
Mounting - Garage/Canopy
• Steel ceiling mount bracket can be secured directly to recessed
junction box, or to the ceiling. The housing hanger bracket allows
fixture to be suspended from ceiling bracket while making wiring
connection. The housing bracket then attaches to the ceiling
bracket via a tool-less latch. A tamper-proof screw can then
secure the bracket.
Electrical Assembly
• The Element II is supplied with a choice of 350 or 530 mA
high‐performance LED drivers that accept 120 v thru 277 v,
50 Hz to 60 Hz, input. Power factor of 90%. Rated for -40 o C
operations.
Solar Vision Pole TM Option
• The Element II LED is compatible for use with Visionaire Lighting’s
Solar Vision Pole TM . Power up to 100 watts (SMR-2 rigid panel)
off‐the‐grid in any locale.
Warranty
• Five (5) year Limited Warranty on entire system, including finish.
For full warranty information, visit VisionaireLighting.com.
Options
• Photocell & receptacle • Cutoff louver system
• Photo receptacle
• Vandal-resistant shield
• Button type photocell • Dual circuit
• Round pole plate adaptor • Motion sensor
• Element conduit box
• Dimming/Controls
Please consult factory for custom options and available
upgrades
Listings
• Element II is listed, suitable for wet locations.
• LM79 and LM80.
• IP65 Listed.
• Dark‐Sky Friendly ® , full cutoff certified by the International
Dark‐Sky Association.
• Meets ANSI C136.31-2001 Vibration Standards at 2G when
ordered with the MAF mounting option.
• DLC Listed.
• RoHS compliant.
• Powder Coated Tough TM .
EL2-2
.8
1.0
1.3
1.4
1.4
1.4
EL2-3
EL2-4
End Mount Only
EL2-5
End Mount Only
.9
1.2
1.3
1.5
1.5
1.5
1.2
1.3
1.6
1.7
2.4
2.3
2.6
2.7
2.6
2.6
2.7
2.7
17.