DRF2008A011 - Dorji
DRF2008A011 - Dorji
DRF2008A011 - Dorji
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>DRF2008A011</strong><br />
<strong>DRF2008A011</strong><br />
High Sensitivity Audio FM Receiver Module V1.00<br />
Features<br />
• Audio PLL receiver module<br />
• 433/868/915Mhz ISM band<br />
• -112dBm sensitivity @ 12dB SINAD<br />
• Low distortion: 0.66%<br />
• Multiple channels<br />
• Audio response:30~30kHz<br />
• Supply voltage: 10~16V<br />
Application<br />
• Car Audio /Car Speaker<br />
• Wireless Microphone<br />
• Ordinary sound box<br />
DESCRIPTION<br />
<strong>DRF2008A011</strong> is a low-cost sub-1 GHz FM receiver module designed for operations in the<br />
unlicensed ISM (Industrial Scientific Medical) and it aims at UHF wireless microphone<br />
applications. The receiver module consists of BPF, LNA, 1 st Mixer1, IF filter, 2 nd MIX and IF<br />
AMP and Demodulator circuit. Users only need to design audio signal process circuit to build a<br />
full audio transmission system and easily apply them in mining industry and electronic consumer<br />
system equipments.<br />
<strong>DRF2008A011</strong><br />
Signal expanding<br />
and decompressing<br />
Figure 1: <strong>DRF2008A011</strong> Receiver System<br />
Revision 1.00 Page 1 of 5 Nov. 2010
<strong>DRF2008A011</strong><br />
PIN FUNCTIONS<br />
Figure 2: <strong>DRF2008A011</strong> Pin Layout<br />
PIN Name Function Description<br />
1 VCC Power Power supply<br />
2 GND Ground Ground (0V)<br />
3 RSSI Output Received signal strength indication<br />
4 AF Output Audio demodulation output: 200±30 mV<br />
5-9 D7-D3 Input ROM control bit (8 th ~4 th ). Logic low: suspended<br />
Logic high: connecting to VDD<br />
10 D2/CLK Input ROM control bit (3 rd ) / Clock input port of MCU. On the rising edge of<br />
clock, data is input to 18-bit shift register of serial interface<br />
11 D1/DATA Input ROM control bit (2 nd ) / Data input port of MCU. The LSB is input first and<br />
the last two bits is group identification code.<br />
12 D0/EN Input ROM control bit (1 st ) / Enable pin. At high level data in shift register will<br />
be loaded in latch distinguished b group identification code.<br />
13 ANT Output Antenna input impedance: 50Ω<br />
14 GND Ground Ground (0V)<br />
Table 1 <strong>DRF2008A011</strong> Pin functions<br />
ELECTRICAL SPECIFICATIONS<br />
Symbol Parameter (condition) Min. Typ. Max. Units<br />
VDD Supply Voltage 10 12 16 V<br />
Temp Operating temperature range -10 25 65 °C<br />
Revision 1.00 Page 2 of 5 Nov. 2010
<strong>DRF2008A011</strong><br />
RH Operating relative humidity 10 90 %<br />
F RX<br />
F OSC<br />
Receive frequency range<br />
433<br />
863<br />
914.2<br />
437.5<br />
864.8<br />
915.7<br />
MHz<br />
MHz<br />
MHz<br />
322.4<br />
326.9 MHz<br />
Oscillator frequency range<br />
752.4<br />
754.2 MHz<br />
903.5<br />
905.0 MHz<br />
C FREQ Crystal Frequency 20 MHz<br />
IDD Transmitting mode @ VCC=10.0V 53 55 60 mA<br />
Sen. Sensitivity @ 12dB SINAD -108 -112 -118 dBm<br />
Dem Demodulation @ 1KHz audio & 20KHz Dev. 170 183 195 mV<br />
RSSI Received signal strength indication @30dB SINAD 1.1 1.41 1.62 V<br />
F RES Frequency response 30 30K Hz<br />
SINAD Signal to noise and distortion ratio@ 20KHz Dev. 40 43 45 dB<br />
SNR Signal to noise ratio@100KHz Dev. 60 dB<br />
D MOD Distortion@ -47dBm signal strength 0.5 0.66 0.9 %<br />
ZANT Antenna Impedance 50 Ohm<br />
Table 2 <strong>DRF2008A011</strong> Electrical Specifications<br />
ABSOLUTE MAXIMUM RATINGS<br />
Symbol Parameter Min. Max. Units<br />
VCC Supply Voltage -0.3 16 V<br />
VI Input voltage -0.3 VCC+0.3 V<br />
VO Output voltage -0.3 VCC+0.3 V<br />
TST Storage temperature -55 125 °C<br />
Table 3 <strong>DRF2008A011</strong> Maximum Ratings<br />
APPLICATION INFORMATION<br />
In order to reduce the complexity of circuit, DORJI provides two types of receiver modules for<br />
selection.<br />
<strong>DRF2008A011</strong>R only works in ROM mode. The channel number and frequency points have been<br />
stored in receiver module. Users can check the ROM Control Logic Table in transmitter module<br />
(DRF2008A131) for details.<br />
<strong>DRF2008A011</strong>M only works together with external MCU for more flexible control on channel<br />
number and frequency points. Users can control the <strong>DRF2008A011</strong>M through 3-wire serial<br />
Revision 1.00 Page 3 of 5 Nov. 2010
<strong>DRF2008A011</strong><br />
interface. As to timing sequence and command word format, please check the datasheet of<br />
transmitter DRF2008A131.<br />
Mechanical Data<br />
Unit: mm<br />
Figure 3: Mechanical Data<br />
Ordering Information<br />
DRF 2008 A 0 11 — 043 D<br />
1 2 3 4 5 6 7<br />
Num Symbol Meaning<br />
1 Module category RF module<br />
2 Module type 2008<br />
3 Module Function Audio FM module<br />
4 Communication way 0: Receiver, 1: Transmitter, 2: Transceiver<br />
5 Sensitivity -112dBm sensitivity @ 12dB SINAD<br />
6 Freq. Band 043: 433MHz<br />
7 Package DIP package<br />
Table 7 Ordering information<br />
Revision 1.00 Page 4 of 5 Nov. 2010
<strong>DRF2008A011</strong><br />
<strong>Dorji</strong> Applied Technologies<br />
A division of <strong>Dorji</strong> Industrial Group Co., Ltd<br />
Add.: Xinchenhuayuan 2, Dalangnanlu, Longhua,<br />
Baoan district, Shenzhen, China 518109<br />
Tel: 0086-755-28156122<br />
Fax.: 0086-755-28156133<br />
Email: sales@rfmodule.me<br />
Web: http://www.rfmodule.me<br />
<strong>Dorji</strong> Industrial Group Co., Ltd reserves the right to<br />
make corrections, modifications, improvements and<br />
other changes to its products and services at any time<br />
and to discontinue any product or service without<br />
notice. Customers are expected to visit websites for<br />
getting newest product information before placing<br />
orders.<br />
These products are not designed for use in life support<br />
appliances, devices or other products where<br />
malfunction of these products might result in personal<br />
injury. Customers using these products in such<br />
applications do so at their own risk and agree to fully<br />
indemnify <strong>Dorji</strong> Industrial Group for any damages<br />
resulting from improper use.<br />
Revision 1.00 Page 5 of 5 Nov. 2010