Shaved 40 - uri=spal-usa

More documents

Recommendations

Info

CHANNEL 6 CHANNEL 4 WHITE/BLACK BROWN Each Kit Contains The Following Components (1) Receiver (1) Emergency Switch (2) Wire Harnesses CIRCUIT COLOR GROUND BLACK CHANNEL 2 INPUT GREEN CHANNEL 7 PURPLE CHANNEL 5 BLUE CHANNEL 3 ORANGE +12V RED IGNITION YELLOW (4) CHANNEL 1/4'' 1 INPUT x 20 GREY x 1 Mounting CHANNEL 6 WHITE/BLACK CHANNEL 4 BROWN Bolts/Nuts/Washers (2) 40-Pound Solenoids CIRCUIT GROUND CHANNEL 2 INPUT CHANNEL 7 CHANNEL 5 CHANNEL 3 +12V IGNITION CHANNEL 1 INPUT CHANNEL 6 CHANNEL 4 COLOR (2) Yellow Butt Connectors BLACK GREEN PURPLE BLUE ORANGE RED YELLOW GREY WHITE/BLACK (2) Yellow 5/16'' Ring Terminals BROWN (2) #10 Blue Rings CIRCUIT GROUND CHANNEL 2 INPUT CHANNEL 7 CHANNEL 5 CHANNEL 3 +12V IGNITION CHANNEL 1 INPUT CHANNEL 6 CHANNEL 4 COLOR BLACK GREEN PURPLE (2) Nylon BLUE Cables ORANGE RED YELLOW GREY (4) WHITE/BLACK Cable Crimps BROWN Installation Instructions for SPAL Shaved Door Handle Kit Shaved-40 This kit is designed to operate two or more functions. Both doors and five other functions can be controlled with the SPAL four-button remote control. The additional channels can be used to operate power door locks, power door releases, trunk releases, control linear actuators, or roll up or down power windows. Channels 1 and 2 are Positive outputs. Channels 3 through 7 are all negative outputs. Please refer to the diagrams on page 7 of this instruction manual for positive, negative, and reverse polarity diagrams. **Proper wiring is critical to the correct operation of this product. Make sure all wires are properly connected, properly grounded, free of potential damage, and are correctly fused** 2
Basic Function of the SPAL Shaved Door Kit The remote control supplied with your kit has four buttons, but is capable of controlling 7 channels. Channel 1: Opens drivers door Channel 2: Channel 3: Channel 4: Channel 5: Channel 6: Channel 7: Operation Section Opens passenger door Optional negative outputs (250 mA) **Additional relays are required for each channel** (See Page 7 For Wiring Diagrams) Negative Trigger Negative Trigger 1 2 3 4 Basic Functions Of The Remote Control To Operate: 1 2 3 Press: 4 5 6 7 8 Channel 1 ON Button 1 Channel 2 Button 2 Channel 3 Button 3 Channel 4 Button 4 Channel 5 Button 1 + Button 2 Channel 6 Button 1 + Button 3 Channel 7 Button 1 + Button 4 TTERY ABLE CRIMPS Brown or Yellow Wire of Receiver Programming Section CIRCUIT COLOR GROUND BLACK CHANNEL 2 INPUT GREEN CHANNEL 7 PURPLE Reprogramming 35 Amp Fuse the Remote Transmitters: CHANNEL 5 BLUE CHANNEL 3 ORANGE EMERGENCY +12V RED **This Shaved Door kit can accept up to 4 IGNITION SPAL remote YELLOW transmitters (Part #MULTI-RCU7TX)** CHANNEL 1 INPUT GREY SWITCH CHANNEL 6 WHITE/BLACK CHANNEL 4 BROWN The remote transmitters are shipped Pre-Programmed. In the event that a remote transmitter loses the programmed code, or if you wish to add more remote transmitters, follow these instructions: • Make sure ignition is OFF. To Brown or Yellow Wire from Spade Connector Harness of Receiver • Locate the programming button located on the side of the receiver, next to the LED. • Press the programming button 3 times quickly (The LED will light). • Press Button (1) on each transmitter you want learned in to the receiver (one at a time). There is a 10 second window to learn all new transmitters. • The LED will remain lit for approximately 10 seconds after the last remote transmitter has been recognized. Negative Trigger • Wait for the LED to go out. Then test each remote transmitter for proper function. Jumper Settings: To avoid damage to attached components, 1 2 3 4 the jumpers must remain in the factory setting. Dip Switch Settings: DOOR LATCH MECHANISM ARM If The Control Unit Is Connected To: DOOR LATCH MECHANISM ARM Dip Settings* 1 2 Solenoids CABLE CRIMPS 1-2: Off 3 4 3-7: Off Actuators 1-2: On 3-7: 35 Amp Fuse Off * Switches 3-8 will always be in the OFF position EMERGENCY SWITCH 3 Negative Trigger Negative Trigger Negative Trigger To Brown or Yellow 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON DIP SWITCHES
Page 1: Shaved 40 Installation Manual & Ope
Page 5 and 6: Mounting / Wiring Section Receiver
Page 7 and 8: Optional Wiring Diagrams Positive O

Shaved 40 - uri=spal-usa

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?