TEF E 204 EExe CABLE GLAND USER MANUAL - Tranberg
TEF E 204 EExe CABLE GLAND USER MANUAL - Tranberg
TEF E 204 EExe CABLE GLAND USER MANUAL - Tranberg
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>TEF</strong> E <strong>204</strong> <strong>EExe</strong><br />
<strong>CABLE</strong> <strong>GLAND</strong> <strong>USER</strong> <strong>MANUAL</strong><br />
IMPORTANT<br />
Read this instruction carefully before installing the<br />
product<br />
E<strong>204</strong> 3 M25<br />
TUM 1055 08.09.10<br />
<strong>Tranberg</strong> AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: (47)51 57 89 00 | Fax.: (47)51 57 89 50<br />
E-mail: info@tranberg.com | www.tranberg.com<br />
<strong>Tranberg</strong> Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80<br />
E-mail: mail@tranbergsystems.com | www.tranbergsystems.com
<strong>TEF</strong> E <strong>204</strong> <strong>EExe</strong> <strong>CABLE</strong> <strong>GLAND</strong> <strong>USER</strong> <strong>MANUAL</strong><br />
INTRODUCTION<br />
Thank you for purchasing this product!<br />
For installation, maintenance and assurance of a long life<br />
of this product, please follow this manual.<br />
TOOLS REQUIRED<br />
Wrench according to size of cable gland<br />
APPLICATIONS<br />
• Outdoor or indoor for unarmoured cables<br />
MAINTENANCE INSTRUCTIONS<br />
CONTENT IN BOX<br />
The product is fully assembled, and ready for installation.<br />
The product should be inspected according to Company<br />
routines.<br />
SAFETY PRECAUTIONS<br />
Note that changes made to the product and/or installation<br />
of components which do not conform to the approval, may<br />
be a safety violation. The manufacturer will in no<br />
circumstance be held responsible for such activity.<br />
For your health and safety, always use safety gear suited<br />
for the task. Be certain to follow codes, regulations and/or<br />
specific procedures that are related to the installation.<br />
APPROVALS<br />
NEMKO 98ATEX392X
<strong>TEF</strong> E <strong>204</strong> <strong>EExe</strong> <strong>CABLE</strong> <strong>GLAND</strong> <strong>USER</strong> <strong>MANUAL</strong><br />
INSTALLATION INSTRUCTIONS<br />
Screw connector (4) into enclosure with a wrench. When<br />
used in sheet metal enclosures, use lock nut inside box<br />
Pass Pressure nut (1) over the cable<br />
Pass washer (2), than Rubber seal (3) over the cable<br />
1<br />
Pressure nut<br />
Carefully cut back the outer sheet of the cable as shown on<br />
drawing<br />
2<br />
Washer<br />
Feed conductors through connector (4). Conductors<br />
and outer sheet goes through the connector (4) and into<br />
enclosure<br />
3 Rubber seal<br />
4 Connector<br />
5 O-ring<br />
Press Rubber seal (3) and Washer (2) into Connector (4) by<br />
hand<br />
Screw Pressure nut (1) into Connector (4) by hand.<br />
Use a wrench to tighten the Pressure nut (1). Make sure<br />
the Rubber seal is tight against the cable. Recommended<br />
torque 10Nm<br />
614A101011<br />
Pull cable to make sure it is secured in rubber seal
<strong>TEF</strong> E <strong>204</strong> <strong>EExe</strong> <strong>CABLE</strong> <strong>GLAND</strong> <strong>USER</strong> <strong>MANUAL</strong><br />
TECHNICAL DATA<br />
Ex-protection:<br />
IP-rating:<br />
Entry seal:<br />
Entry threads:<br />
Thread length:<br />
Material:<br />
II 2 G <strong>EExe</strong> II<br />
IP66/67<br />
O-ring<br />
Metric / PG / NPT<br />
9/15 mm<br />
Brass / AISI 316L<br />
Material seal: Neoprene: -25°C to +85°C<br />
Fluorrubber<br />
-20°C to +200°C<br />
Application:<br />
Function:<br />
Outdoor enclosures<br />
Seal on outer sheet only<br />
<strong>Tranberg</strong> AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: (47)51 57 89 00 | Fax.: (47)51 57 89 50<br />
E-mail: info@tranberg.com | www.tranberg.com<br />
<strong>Tranberg</strong> Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80<br />
E-mail: mail@tranbergsystems.com | www.tranbergsystems.com