MERCEDES 307 D - 310 D - Topdrivesystem.it
MERCEDES 307 D - 310 D - Topdrivesystem.it
MERCEDES 307 D - 310 D - Topdrivesystem.it
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
4.0161-IM-VB-ECO<br />
ENG<br />
Distributed by:<br />
VB air suspension<br />
Varsseveld-Holland<br />
Frankenweg 3<br />
Varsseveld-Holland<br />
This leaflet is purely for illustrative purposes and may not reflect correctly the supplied parts. The manufacturer reserves<br />
to amend the contents of <strong>it</strong> whenever necessary and w<strong>it</strong>hout notice.<br />
VB-Airsuspension ref.<br />
1520201001<br />
Rear integrative pneumatic suspension for<br />
<strong>MERCEDES</strong> <strong>307</strong> D - <strong>310</strong> D<br />
Until 12/1996
INSTALLATION INSTRUCTIONS<br />
PACKAGE CONTENT<br />
Pressures sticker (1X) Pneumatic system instructions (1x)<br />
Left suspension (1X)<br />
Right suspension (1X)<br />
Ø 80 (2x)<br />
Plate (1X) Plate (1X)<br />
M10x25 (4x)<br />
Locking plate (2X)<br />
RILSAN KIT :<br />
Red pipe (6m) Black pipe (6m)<br />
Inflating valves (2x)<br />
CLIPS KIT :<br />
Plastic clips (10x)<br />
Small hardware k<strong>it</strong><br />
RIGHT SIDE<br />
RIGHT SIDE RIGHT SIDE<br />
1 2 3<br />
Place the vehicle in a hole or<br />
bridge, to operate SAFE and<br />
comfortably.<br />
Remove rebound pad and give to<br />
the end user.<br />
Place the locking plate provided<br />
inside rebound pad support.<br />
RIGHT SIDE<br />
RIGHT SIDE RIGHT SIDE<br />
4<br />
5 6<br />
Place the suspension between axle<br />
and chassis ( center holes in the<br />
locking plate ).<br />
Lock the suspension on the locking<br />
plate w<strong>it</strong>h provided screws..<br />
Lock the suspension on the axle<br />
w<strong>it</strong>h provided clamps..<br />
RIGHT SIDE<br />
7<br />
F<strong>it</strong> RILSAN pipe on suspension pipe f<strong>it</strong>ting: :<br />
• Red for right side<br />
• Black for left side.<br />
BRAKE REGULATOR MODIFICATION INSTRUCTION<br />
1<br />
2<br />
3<br />
Unscrew the side fixed to the axle of<br />
the adjustor drive rod, as showed on<br />
the picture.<br />
Place in between the holed plate and<br />
lock by mean of screws and bolts as<br />
showed in picture.<br />
Pos<strong>it</strong>ion of the drive adjustor modified<br />
correcyly.<br />
WARNING : For the execution of the pneumatic system, please strictly refer the specific given instructions. In fact , the system may vary according to the chosen<br />
version (manual, self levelling or electrical); so than the instructions for the pneumatic system are stated in the appos<strong>it</strong>e handbook enclosed at the purchased k<strong>it</strong>.<br />
IMPORTANT: do NOT use liquid Teflon®, hemp, paints etc. .In case of problem and/or information, contact our technical office. In case you fail to comply at this indications,<br />
VB-Airsuspension isn’t responsible for eventually damages derivates. For further information contact us.