Darrtt Controls Full Linnee Catalog - Dart Controls

Tach
MD SERIES SELECTION GUIDE
MODEL MAX. ARM MAX
NUMBER DC AMPS H.P. INPUT OUTPUT
MOUNTING SPECIFICATIONS
CONTROLS Page
Ite
Valu
m
4.000"
Tach
ENTER
4.000"
3.622"
MD10P
HOUSING DEPTH
4.625"
0.885"
1.770"
1/8 DIN
MICRO-DRIVE
.140" x 2
PANEL CUT-OUT
MD3E
-Sensor must have minimum output current of 10 mA.
-Drive includes supply for external sensor of 5VDC @50 mA max.
-Shipped set for 0-2400 RPM with one pulse per revolution.
MICRO-DRIVE
CONTROLS
ENTER
.140" x 4
3.622
MD3P
HOUSING DEPTH
4.625"
PANEL CUT-OUT
0.811"
3.622"
2.000"
OPERATING SPECIFICATIONS
Temperature ...........................................................
AC input voltage ........................................................ 85–265 VAC
Input frequency ...............................................................
Overload capacity ............................................
Transducer signal input .......................................
...........................................5 VDC, 50mA
DIMENSIONAL SPECIFICATIONS
MODEL WIDTH HEIGHT DEPTH
MD10P inches (millimeters)
Housing 3.620 (91.95) 1.656 (42.06) 4.625 (117.47)
Lens 4.539 (115.29) 2.289 (58.13) 0.375 (9.52)
MD3P inches (millimeters)
Housing 3.620 (91.95) 3.497 (88.82) 4.625 (117.47)
Lens 4.539 (115.29) 4.179 (106.15) 0.375 (9.52)
1/4 DIN
WIRING DIAGRAMS
MD3E
P1-1
P1-2
P1-3
P1-4
P1-5
P1-6
P1-7
P1-8
P1-9
P1-10
P1-11
P1-12
N
L
-A
+A
COM
+5V
S1
S2
NO
C
NC
IN1
-ARM
+ARM
COMMON
+5VDC
SIGNAL
*Jog Input
Ground Lug
AC INPUT
AC INPUT} 85-265VAC
black
red
white
Alarm Output - Normally Open
Alarm Output - Common
Alarm Output - Normally Closed
*INHIBIT
User Input 1
MOTOR
COM (P1-5)
}
Form
* P1-8 & P1-12 user input may be programmed
for a number of functions. Including (jog, inhibit, etc.)
C
Relay Output
(Programmable)
PICK-UP MOUNTED
TO MOTOR SHAFT
(Mounts on rotating
end shaft with 10-32
tapped hole, 1/2" deep)
MOUNTING SPECIFICATIONS MD3E
5.530
Page Item Valu Tach
ENTER
7/32" TYP.
(4 SLOTS)
.350 DEEP
MDP
MASTER
P1-1
P1-2
P1-3
P1-4
P1-5
P1-6
P1-7
P1-8
P1-9
P1-10
P1-11
P1-12
AC INPUT
FUSE
N
MD10P = 7.5 Amp* }85-265VAC
MD3P = 15 Amp*
L
AC INPUT
-A
-ARM
+A
+ARM
MOTOR
COM
COMMON black
+5V
+5VDC red
S1
SIGNAL white
S2
**Jog Input
NO Alarm Output - Normally Open
C Alarm Output - Common
Form C
Relay Output
NC Alarm Output - Normally Closed}
(Programmable)
IN1
User Input 1
**INHIBIT
PICK-UP MOUNTED
TO MOTOR SHAFT
(Mounts on rotating
end shaft with 10-32
tapped hole, 1/2" deep)
COM (P1-5)
black
CONTROLS
* For AC inputs utilizing two hot lines, both inputs should be
protected with appropriately sized fuses or circuit breakers.
** P1-8 & P1-12 user input may be programmed
for a number of functions. Including (jog, inhibit, etc.)
white
7.400
ON
OFF
5.500
.750
MDP
FOLLOWER
P1-1
P1-2
P1-3
P1-4
P1-5
P1-6
P1-7
P1-8
P1-9
P1-10
P1-11
P1-12
N
L
FUSE
MD10P = 7.5 Amp*
MD3P = 15 Amp*
-A
-ARM
+A
+ARM
COM
COMMON
+5V
+5VDC
S1
SIGNAL 1
S2
NO Alarm Output - Normally Open
C Alarm Output - Common
NC Alarm Output - Normally Closed
IN1
User Input 1
**INHIBIT
SIGNAL 2
COM (P1-5)
AC INPUT
}85-265VAC
AC INPUT
}
MOTOR
black
red
white
Form C
Relay Output
(Programmable)
FOLLOWER PICK-UP
MOUNTED TO
MOTOR SHAFT
(Mounts on rotating
end shaft with 10-32
tapped hole, 1/2" deep)
5.125 TYP.
* For AC inputs utilizing two hot lines, both inputs should be
protected with appropriately sized fuses or circuit breakers.
** P1-8 & P1-12 user input may be programmed
for a number of functions. Including (jog, inhibit, etc.)
www.dartcontrols.com
15