Operating Instructions No. 705-2 USA

More documents

Recommendations

Info

5.4 Lubrification All greasing points of your windrower are shown on this page. Observation of the maintenance and greasing intervals laid down will prolong the service life of the implement. As a rule, disengage the drive mechanism and stop the tractor before carrying out any maintenance, servicing or cleaning work and before remedying operational disorders. Always remove the ignition key from the tractor. Use oils and greases produced on vegetable basis. 20h 20h 20h KS200042 20h KS200043 The cam track can be lubricated through the lubrication nipple (1) located in the lower part of the rotor. Apply the grease to the area between guide roller and cam track and turn the rotor several times to allow the grease to be distributed over the entire cam track. 20h KS200044 22
6. Winter storage 1. Store the machine in a weather-proof building. Never store the machine next to artificial fertilizers. 2. Thoroughly clean the machine. Dirt involves the formation of moisture which entails rusting. If cleaning with a high-pressure washing device do not direct the water jet at the bearings. 3. Make sure all movable parts such as tension pulleys, hinges etc. move freely. If necessary movable parts have to be removed, cleaned, checked for wear and replaced by new ones as required. 4. Lubricate all hinge points. 5. Lubricate the machine thoroughly. 6. Grease the PTO shaft guard tubes to prevent them freezing. 7. Touch up damaged paintwork, spray damaged areas with anti-rust fluid. 8. Clean chains with diesel fuel, let dry and lubricate with viscous oil. 7. Starting-up after winter storage 1. Remove oil and grease which was applied for the preservation of chains and the machine. 2. Grease the machine completely to allow any accumulation of condensed water in the bearings to be eliminated. 3. Check the inflation pressure in the tyres. 4. Check the oil level in the gearbox an top up as laid down by the manufacturer. 5. Retighten all bolts and nuts. 6. Be sure all machine components are correctly adjusted and readjust as required. 7. Spin the slip clutch to free the linings. 9. Read thoroughly the instruction manual again. Important: Use oils and greases produced on vegetable basis. 9. Jack up the machine to relieve load on tyres, do not deflate tyres, protect tyres against sun, grease and oil. 10. Take a note of all spare parts required and order them in time. It will be easier for your KRONE Dealer to supply and install spare parts before the start of the season. What is more, your machine will be ready for use before the start of the next season. What is more, your machine will be ready for use before the start of the next season. 23
Page 1: Operating Instructions No. 705-2 US
Page 4 and 5: List of contents 1. Introduction ..
Page 6 and 7: 23.Keep clear of the swinging area
Page 8 and 9: 1. Introduction The KRONE rotary sw
Page 10: 1.2 Positioning of the general safe
Page 13 and 14: 2.3 PTO shaft 2.3.1 General informa
Page 15 and 16: 2.4 Disconnection from the tractor
Page 17 and 18: 3.3 Schutzbügel umklappen • Äu
Page 19 and 20: 4. Road travel regulations 4.1 Tran
Page 21: 5.3 Tyres • Installation of tyres
Page 25 and 26: 9. Technical Data Type Swadro 345 S
Page 27 and 28: • Muttern (1) von den vier Radach
Page 29 and 30: • Den Tragholm (1) mittels Hebevo
Page 31 and 32: • Konsole (1) mit Schrauben M 12
Page 33 and 34: • Remove split pin and washer fro
Page 36: . . . konsequent, kompetent Maschin

Operating Instructions No. 705-2 USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?