Hi-Di® Diamond Burs - Dentsply
Hi-Di® Diamond Burs - Dentsply
Hi-Di® Diamond Burs - Dentsply
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Sterilisation Instructions<br />
1. WARNINGS: <strong>Burs</strong> are not sterile upon receipt<br />
and must be sterilised before use in accordance<br />
with the following instructions. <strong>Burs</strong> can be<br />
damaged by alkaline and acidic detergents.<br />
Always use a pH neutral detergent or solution.<br />
Do not exceed 140°C. Remove all packaging<br />
prior to cleaning and sterilisation.<br />
Contaminated burs should be handled<br />
with gloves and eye protection should be<br />
used.<br />
2. Limitations on reprocessing: Repeated<br />
processing has minimal effect on these burs. End<br />
of life is normally determined by wear and<br />
damage due to use.<br />
See Inspection. NOTE: Steel <strong>Burs</strong> are single use<br />
only. Cannot be reprocessed. See Inspection.<br />
INSTRUCTIONS<br />
3. Point of use: Remove from packaging.<br />
DIAMOND/ TUNGSTEN BURS: Remove all excess<br />
soil with disposable cloth paper wipe.<br />
4. Containment and Transportation: Protect<br />
delicate or fine burs from damage. <strong>Burs</strong> left<br />
standing wet may stain or corrode.<br />
DIAMOND/TUNGSTEN BURS: <strong>Burs</strong> should be<br />
reprocessed as soon as is reasonably practical<br />
following use.<br />
5. Preparation for cleaning: No specific<br />
requirements. Disassembly not required.<br />
6. Automatic Cleaning: Equipment: Use only<br />
validated washing machines (HTM 2030: UK only)<br />
and validated cleaning agents suitable for both<br />
devices and washing machines. Follow instructions<br />
issued by both the equipment and cleaning agent<br />
manufacturers. When unloading, inspect for<br />
complete removal of visible soil. If necessary,<br />
repeat cycle, or use manual cleaning before<br />
repeating cycle.<br />
7. Maintenance: Discard damaged burs.<br />
8. Inspection and Function Testing: All <strong>Burs</strong>:<br />
Visually inspect to ensure all contamination has been<br />
removed. Check for damage and wear. Cutting<br />
edges should be free of defects. Discard damaged or<br />
corroded burs. Check burs with long, slender<br />
features for distortion. Where burs form part of a<br />
larger assembly, check assembly with mating<br />
components. There may be evidence of<br />
discolouration or dulling after sterilisation. This is<br />
normal and will not affect performance.<br />
9. Drying: Dry using paper towelling or dry heat<br />
not exceeding 140°C.<br />
10. Packaging for Sterilisation: The UK Dept.<br />
of Health recommends that validated, pre-vacuum<br />
autoclaves are used for sterilising wrapped burs.<br />
Autoclaves drawing only a post-sterilisation vacuum<br />
for drying purposes are not suitable for processing<br />
wrapped burs. <strong>Burs</strong> may be loaded into dedicated<br />
instrument trays or general-purpose sterilisation<br />
trays. Ensure that cutting edges are protected.<br />
11. Sterilisation: Use only validated vacuum<br />
autoclaves (Refer to HTM2010: UK only).<br />
Do not exceed 140°C.<br />
Sterilisation<br />
temperature range<br />
(°C)<br />
Minimum<br />
134<br />
Nominal<br />
pressure<br />
(mPa)<br />
Minimum time<br />
at temperature*<br />
(in minutes)<br />
Maximum<br />
137 0.225 3<br />
*Minimum holding time when nominal operating<br />
temperature and pressure have been reached.<br />
12. Storage: Avoid contamination.<br />
13. Additional Information: When sterilising<br />
multiple burs in one autoclave cycle, ensure that<br />
the manufacturer’s stated maximum load is not<br />
exceeded. Validated ultrasonic baths may be used<br />
with validated cleaning agents. Follow<br />
instructions for use issued by both the equipment<br />
and cleaning agent manufacturers.<br />
These instructions have been validated by the<br />
manufacturer as being capable of preparing a<br />
device for re-use. It remains the responsibility of the<br />
reprocessor to ensure that the reprocessing has<br />
actually achieved the desired result. This normally<br />
requires validation and routine monitoring of the<br />
process. Any deviation by the reprocessor from<br />
these instructions should be properly evaluated<br />
for effectiveness and potential adverse effects.<br />
THE CUTTING EDGE...<br />
For further details contact DENTSPLY<br />
Ash ® Instruments on +44 (0)1932 853422<br />
Visit www.dentsply.com<br />
or www.ash-instruments.com<br />
Ask your local DENTSPLY subsidiary or dental<br />
wholesaler for supplies outside the UK or Ireland.<br />
UKP00056 03/07
INTRODUCTION<br />
Customer Satisfaction<br />
Customer satisfaction continues to be the key aim<br />
at DENTSPLY Ash ® Instruments’ and as a result,<br />
you can expect to receive the highest standard of<br />
products and services.<br />
As a valued customer, the aim of this brochure is<br />
to provide you with an insight into DENTSPLY Ash ®<br />
Instruments rotary burs, including the well-respected<br />
<strong>Hi</strong>-Di ® diamond range. <strong>Hi</strong>-Di ® has been in the UK<br />
market for decades and has remained an important<br />
brand within the Ash ® Instrument range.<br />
Comprehensive Range<br />
<strong>Hi</strong>-Di ® diamonds offer a comprehensive range of<br />
diamond burs, including various patterns and<br />
varying grits - this ensures most clinical situations<br />
are met.<br />
Other rotary burs available:<br />
Ash ® TC Rotary and Oral<br />
Surgery <strong>Burs</strong><br />
Ash ® Supercut ® Tungsten Carbide <strong>Burs</strong><br />
F.G. Round Head<br />
<strong>Hi</strong>-Di ® No.<br />
720<br />
ISO 001-007<br />
<br />
60703720<br />
<strong>Hi</strong>-Di ® No.<br />
681<br />
ISO 001-008<br />
<br />
60703681<br />
<strong>Hi</strong>-Di ® No.<br />
519<br />
ISO 001-009<br />
<br />
60703519<br />
<strong>Hi</strong>-Di ® No.<br />
520<br />
ISO 001-010<br />
<br />
60703520<br />
<strong>Hi</strong>-Di ® No.<br />
520 Short<br />
ISO 001-010<br />
<br />
60713520<br />
<strong>Hi</strong>-Di ® No.<br />
521<br />
ISO 001-012<br />
<br />
60704521<br />
<br />
60703521<br />
<strong>Hi</strong>-Di ® No.<br />
521 Short<br />
ISO 001-012<br />
<br />
60713521<br />
<strong>Hi</strong>-Di ® No.<br />
708<br />
ISO 001-014<br />
<br />
60703708<br />
<strong>Hi</strong>-Di ® No.<br />
522<br />
ISO 001-016<br />
<br />
60703522<br />
<br />
60702522<br />
<strong>Hi</strong>-Di ® No.<br />
644<br />
ISO 001-018<br />
<br />
60703644<br />
<strong>Hi</strong>-Di ® No.<br />
645<br />
ISO 001-021<br />
<br />
60703645<br />
<strong>Hi</strong>-Di ® DIAMOND BURS<br />
Combining quality craftsmanship and the finest<br />
materials available, <strong>Hi</strong>-Di ® diamonds meet<br />
rigorous standards and pass exacting quality tests.<br />
F.G. Pear Head<br />
<strong>Hi</strong>-Di ® <strong>Diamond</strong> <strong>Burs</strong><br />
Ash ® <strong>Hi</strong>-Di ® <strong>Diamond</strong> <strong>Burs</strong><br />
<strong>Hi</strong>gh Quality<br />
These provide a super tough cutting edge for<br />
high-speed applications. Manufactured to a high<br />
standard, this comprehensive range provides the<br />
clinician with a quality rotary bur.<br />
Ash ® Steel <strong>Burs</strong><br />
Ash ® Steel <strong>Burs</strong><br />
<strong>Hi</strong>-Di ® No.<br />
601<br />
ISO 001-025<br />
<br />
60703601<br />
<strong>Hi</strong>-Di ® No.<br />
646<br />
ISO 001-033<br />
<br />
60703646<br />
<strong>Hi</strong>-Di ® No.<br />
643<br />
ISO 001-042<br />
<br />
60703643<br />
<strong>Hi</strong>-Di ® No.<br />
648<br />
ISO 002-014<br />
<br />
60703648<br />
<strong>Hi</strong>-Di ® No.<br />
525<br />
ISO 237-010<br />
<br />
60703525<br />
<strong>Hi</strong>-Di ® No.<br />
525 Short<br />
ISO 237-010<br />
<br />
60713525<br />
<strong>Hi</strong>-Di ® No.<br />
526<br />
ISO 237-012<br />
<br />
60703526<br />
<strong>Hi</strong>-Di ® No.<br />
527<br />
ISO 237-016<br />
<br />
60703527<br />
<strong>Hi</strong>-Di ® No.<br />
565<br />
ISO 233-010<br />
<br />
60703565<br />
<strong>Hi</strong>-Di ® No.<br />
566<br />
ISO 233-012<br />
<br />
60703566<br />
<strong>Hi</strong>-Di ® No.<br />
567<br />
ISO 234-014<br />
<br />
60703567<br />
<strong>Hi</strong>-Di ® diamonds have multiple layers of diamond<br />
grit that provide fast, reliable cutting, and extend<br />
the life of the diamond.<br />
Made from precision-engineered shanks, <strong>Hi</strong>-Di ®<br />
diamonds help to minimise handpiece vibration<br />
and thus increases comfort among both patients<br />
and dentists. In addition, a de-embrittlement<br />
process ensures <strong>Hi</strong>-Di ® diamonds remain a<br />
durable diamond bur, offering longevity and longterm<br />
economy.<br />
100% Assurance<br />
Our rigid inspection standards ensure you will<br />
receive the unmatched quality, which you have<br />
come to expect from DENTSPLY Ash ® Instruments.<br />
These rotary burs are designed for single use only,<br />
and provide another option for the clinician.<br />
DENTSPLY Ash ® Instruments guarantees the quality<br />
of these rotary burs 100%! If you are not satisfied<br />
with any Ash ® rotary bur, simply return it for a<br />
replacement.<br />
For further information on any of the rotary<br />
burs listed here, please contact DENTSPLY<br />
Ash ® Instruments on +44 (0) 1932 853422<br />
<strong>Hi</strong>-Di ® No.<br />
670<br />
ISO 238-012<br />
<br />
60703670<br />
<strong>Hi</strong>-Di ® No.<br />
671<br />
ISO 238-014<br />
<br />
60703671<br />
<strong>Hi</strong>-Di ® No.<br />
672<br />
ISO 238-016<br />
<br />
60703672<br />
<strong>Hi</strong>-Di ® No.<br />
673<br />
ISO 238-014<br />
<br />
60703673<br />
<strong>Hi</strong>-Di ® No.<br />
674<br />
ISO 238-016<br />
<br />
60703674<br />
F.G. Inverted Cone<br />
<strong>Hi</strong>-Di ® No.<br />
530<br />
ISO 012-010<br />
<br />
60703530<br />
<strong>Hi</strong>-Di ® No.<br />
709<br />
ISO 012-012<br />
<br />
60703709<br />
<strong>Hi</strong>-Di ® No.<br />
531<br />
ISO 012-014<br />
<br />
60703531<br />
<strong>Hi</strong>-Di ® No.<br />
534<br />
ISO 225-014<br />
<br />
60703534<br />
<strong>Hi</strong>-Di ® No.<br />
535<br />
ISO 225-016<br />
<br />
60703535<br />
<strong>Hi</strong>-Di ® No.<br />
605<br />
ISO 225-018<br />
<br />
60703605<br />
ISO Explanation<br />
<strong>Hi</strong> Di ® 541, e.g. 108-010<br />
108= ISO pattern reference<br />
010= Nominal head diameter (1.0mm)<br />
Extra Fine<br />
Fine<br />
Medium<br />
Coarse<br />
F.G. Diabolo<br />
F.G.Wheel<br />
<strong>Hi</strong>-Di ® No.<br />
653<br />
ISO 019-009<br />
<br />
60703653<br />
<strong>Hi</strong>-Di ® No.<br />
654<br />
ISO 019-011<br />
<br />
60703654<br />
<strong>Hi</strong>-Di ® No.<br />
536<br />
ISO 019-010<br />
<br />
60703536<br />
<strong>Hi</strong>-Di ® No.<br />
537<br />
ISO 019-012<br />
<br />
60703537<br />
<strong>Hi</strong>-Di ® No.<br />
721<br />
ISO 019-013<br />
<br />
60703721<br />
<strong>Hi</strong>-Di ® No.<br />
538<br />
ISO 019-014<br />
<br />
60703538<br />
<strong>Hi</strong>-Di ® No.<br />
608<br />
ISO 019-016<br />
<br />
60703608<br />
<strong>Hi</strong>-Di ® No.<br />
512<br />
ISO 041-018<br />
<br />
60703512<br />
<strong>Hi</strong>-Di ® No.<br />
514<br />
ISO 042-042<br />
<br />
60703514<br />
<strong>Hi</strong>-Di ® No.<br />
619<br />
ISO 068-036<br />
<br />
60703619<br />
<strong>Hi</strong>-Di ® No.<br />
513<br />
ISO 068-042<br />
<br />
60703513
<strong>Hi</strong>-Di ® DIAMOND BURS<br />
<strong>Hi</strong>-Di ® No.<br />
620<br />
ISO 068-045<br />
<br />
60703620<br />
F.G. Cylindrical<br />
<strong>Hi</strong>-Di ® No.<br />
744<br />
ISO 108-007<br />
<br />
60703744<br />
<strong>Hi</strong>-Di ® No.<br />
732<br />
ISO 108-008<br />
<br />
60703732<br />
<strong>Hi</strong>-Di ® No.<br />
727<br />
ISO 108-009<br />
<br />
60703727<br />
<strong>Hi</strong>-Di ® No.<br />
541<br />
ISO 108-010<br />
<br />
60704541<br />
<br />
60703541<br />
<strong>Hi</strong>-Di ® No.<br />
541 Short<br />
ISO 108-010<br />
<br />
60713541<br />
<strong>Hi</strong>-Di ® No.<br />
730<br />
ISO 108-012<br />
<br />
60703730<br />
<strong>Hi</strong>-Di ® No.<br />
700<br />
ISO109-009<br />
<br />
60703700<br />
<strong>Hi</strong>-Di ® No.<br />
745<br />
ISO 109-010<br />
<br />
60704745<br />
<br />
60703745<br />
<strong>Hi</strong>-Di ® No.<br />
606<br />
ISO 109-012<br />
<br />
60703606<br />
<strong>Hi</strong>-Di ® No.<br />
542<br />
ISO 109-014<br />
<br />
60704542<br />
<br />
60703542<br />
F.G.<br />
Cylindrical<br />
Domed<br />
<strong>Hi</strong>-Di ® No.<br />
625<br />
ISO 172-020<br />
<br />
60703625<br />
<strong>Hi</strong>-Di ® No.<br />
559<br />
ISO 173-012<br />
<br />
60703559<br />
<strong>Hi</strong>-Di ® No.<br />
557<br />
ISO 173-013<br />
<br />
60704557<br />
<br />
60703557<br />
<br />
60702557<br />
<strong>Hi</strong>-Di ® No.<br />
560<br />
ISO 173-014<br />
<br />
60703560<br />
<strong>Hi</strong>-Di ® No.<br />
556<br />
ISO 173-016<br />
<br />
60704556<br />
<br />
60703556<br />
<br />
60702556<br />
<strong>Hi</strong>-Di ® No.<br />
626<br />
ISO 173-018<br />
<br />
60704626<br />
<br />
60703626<br />
<strong>Hi</strong>-Di ® No.<br />
627<br />
ISO173-020<br />
<br />
60703627<br />
<strong>Hi</strong>-Di ® No.<br />
628<br />
ISO 174-018<br />
<br />
60703628<br />
<strong>Hi</strong>-Di ® No.<br />
629<br />
ISO 174-020<br />
<br />
60703629<br />
<strong>Hi</strong>-Di ® No.<br />
630<br />
ISO 174-022<br />
<br />
60703630<br />
F.G. Flame<br />
<strong>Hi</strong>-Di ® No.<br />
651<br />
ISO 243-018<br />
<br />
60703651<br />
<br />
60701651<br />
<strong>Hi</strong>-Di ® DIAMOND BURS<br />
<strong>Hi</strong>-Di ® No.<br />
542 Short<br />
ISO 109-014<br />
<br />
60713542<br />
<strong>Hi</strong>-Di ® No.<br />
656<br />
ISO 109-016<br />
<br />
60703656<br />
<strong>Hi</strong>-Di ® No.<br />
543<br />
ISO 109-018<br />
<br />
60703543<br />
<strong>Hi</strong>-Di ® No.<br />
657<br />
ISO 110-012<br />
<br />
60703657<br />
<strong>Hi</strong>-Di ® No.<br />
546<br />
ISO 110-014<br />
<br />
60704546<br />
<br />
60703546<br />
<strong>Hi</strong>-Di ® No.<br />
607<br />
ISO 110-016<br />
<br />
60703607<br />
<strong>Hi</strong>-Di ® No.<br />
658<br />
ISO 111-010<br />
<br />
60703658<br />
<strong>Hi</strong>-Di ® No.<br />
710<br />
ISO 111-012<br />
<br />
60703710<br />
<strong>Hi</strong>-Di ® No.<br />
659<br />
ISO 111-014<br />
<br />
60703659<br />
<strong>Hi</strong>-Di ® No.<br />
660<br />
ISO 111-016<br />
<br />
60703660<br />
<strong>Hi</strong>-Di ® No.<br />
544<br />
ISO 138-010<br />
<br />
60703544<br />
<strong>Hi</strong>-Di ® No.<br />
564<br />
ISO 243-022<br />
<br />
60703564<br />
<strong>Hi</strong>-Di ® No.<br />
650<br />
ISO 247-010<br />
<br />
60703650<br />
<br />
60701650<br />
<strong>Hi</strong>-Di ® No.<br />
561<br />
ISO 247-016<br />
<br />
60703561<br />
<br />
60702561<br />
<strong>Hi</strong>-Di ® No.<br />
722<br />
ISO 248-012<br />
<br />
60703722<br />
<strong>Hi</strong>-Di ® No.<br />
652<br />
ISO 249-011<br />
<br />
60701652<br />
<strong>Hi</strong>-Di ® No.<br />
719<br />
ISO 249-014<br />
<br />
60703719<br />
<strong>Hi</strong>-Di ® No.<br />
562<br />
ISO 249-016<br />
<br />
60703562<br />
<br />
60702562<br />
<strong>Hi</strong>-Di ® No.<br />
675<br />
ISO 250-012<br />
<br />
60701675<br />
<strong>Hi</strong>-Di ® No.<br />
676<br />
ISO 250-014<br />
<br />
60703676<br />
<strong>Hi</strong>-Di ® No.<br />
723<br />
ISO 257-018<br />
<br />
60703723<br />
<strong>Hi</strong>-Di ® No.<br />
724<br />
ISO 257-023<br />
<br />
60703724<br />
<br />
60701724<br />
F.G. Cylindrical Pointed<br />
F.G. Tapered Round End<br />
<strong>Hi</strong>-Di ® No.<br />
729<br />
ISO 139-009<br />
<br />
60703729<br />
<strong>Hi</strong>-Di ® No.<br />
731<br />
ISO 139-012<br />
<br />
60703731<br />
<strong>Hi</strong>-Di ® No.<br />
545<br />
ISO 139-014<br />
<br />
60703545<br />
<strong>Hi</strong>-Di ® No.<br />
715<br />
ISO 141-010<br />
<br />
60703715<br />
<strong>Hi</strong>-Di ® No.<br />
613<br />
ISO 129-010<br />
<br />
60703613<br />
<strong>Hi</strong>-Di ® No.<br />
614<br />
ISO 130-010<br />
<br />
60703614<br />
<strong>Hi</strong>-Di ® No.<br />
615<br />
ISO 130-012<br />
<br />
60703615<br />
<strong>Hi</strong>-Di ® No.<br />
678<br />
ISO 288-012<br />
<br />
60703678<br />
<strong>Hi</strong>-Di ® No.<br />
716<br />
ISO 289-012<br />
<br />
60703716<br />
<strong>Hi</strong>-Di ® No.<br />
679<br />
ISO 289-014<br />
<br />
60703679<br />
<strong>Hi</strong>-Di ® No.<br />
680<br />
ISO 290-012<br />
<br />
60703680<br />
<strong>Hi</strong>-Di ® No.<br />
773<br />
ISO 277-023<br />
<br />
60703773<br />
<br />
60701773<br />
<strong>Hi</strong>-Di ® No.<br />
633<br />
ISO 196-012<br />
<br />
60703633<br />
<strong>Hi</strong>-Di ® No.<br />
501<br />
ISO 197-016<br />
<br />
60703501<br />
<strong>Hi</strong>-Di ® No.<br />
713<br />
ISO 197-012<br />
<br />
60703713<br />
<strong>Hi</strong>-Di ® No.<br />
634<br />
ISO 197-016<br />
<br />
60703634<br />
<strong>Hi</strong>-Di ® No.<br />
635<br />
ISO 197-018<br />
<br />
60704635<br />
<br />
60703635<br />
<strong>Hi</strong>-Di ® No.<br />
504<br />
ISO 198-012<br />
<br />
60703504<br />
<strong>Hi</strong>-Di ® No.<br />
664<br />
ISO 198-014<br />
<br />
60703664<br />
<strong>Hi</strong>-Di ® No.<br />
636<br />
ISO 198-016<br />
<br />
60703636<br />
<strong>Hi</strong>-Di ® No.<br />
638<br />
ISO 198-018<br />
<br />
60703638<br />
<strong>Hi</strong>-Di ® No.<br />
637<br />
ISO 198-020<br />
<br />
60703637<br />
F.G. Truncated Cone<br />
F.G. Tapered Pointed<br />
<strong>Hi</strong>-Di ® No.<br />
717<br />
ISO 290-014<br />
<br />
60703717<br />
<strong>Hi</strong>-Di ® No.<br />
550<br />
ISO 169-010<br />
<br />
60703550<br />
<strong>Hi</strong>-Di ® No.<br />
551<br />
ISO 170-012<br />
<br />
60703551<br />
<strong>Hi</strong>-Di ® No.<br />
552<br />
ISO 170-016<br />
<br />
60703552<br />
<strong>Hi</strong>-Di ® No.<br />
554<br />
ISO 171-014<br />
<br />
60704554<br />
<br />
60703554<br />
<strong>Hi</strong>-Di ® No.<br />
622<br />
ISO 171-016<br />
<br />
60703622<br />
<strong>Hi</strong>-Di ® No.<br />
661<br />
ISO 172-010<br />
<br />
60703661<br />
<strong>Hi</strong>-Di ® No.<br />
712<br />
ISO 172-012<br />
<br />
60703712<br />
<strong>Hi</strong>-Di ® No.<br />
555<br />
ISO 172-014<br />
<br />
60703555<br />
<strong>Hi</strong>-Di ® No.<br />
623<br />
ISO 172-016<br />
<br />
60703623<br />
<strong>Hi</strong>-Di ® No.<br />
624<br />
ISO 172-018<br />
<br />
60703624<br />
<strong>Hi</strong>-Di ® No.<br />
714<br />
ISO 199-012<br />
<br />
60703714<br />
<strong>Hi</strong>-Di ® No.<br />
502<br />
ISO 199-014<br />
<br />
60703502<br />
<strong>Hi</strong>-Di ® No.<br />
639<br />
ISO 199-016<br />
<br />
60703639<br />
<strong>Hi</strong>-Di ® No.<br />
503<br />
ISO 199-018<br />
<br />
60703503<br />
<strong>Hi</strong>-Di ® No.<br />
640<br />
ISO 199-020<br />
<br />
60703640<br />
<strong>Hi</strong>-Di ® No.<br />
641<br />
ISO 200-018<br />
<br />
60703641<br />
<strong>Hi</strong>-Di ® No.<br />
642<br />
ISO 201-018<br />
<br />
60703642<br />
<strong>Hi</strong>-Di ® No.<br />
742<br />
ISO 160-009<br />
<br />
60703742<br />
<strong>Hi</strong>-Di ® No.<br />
733<br />
ISO 160-012<br />
<br />
60703733<br />
<strong>Hi</strong>-Di ® No.<br />
753<br />
ISO 160-014<br />
<br />
60703753<br />
<br />
60701753<br />
<strong>Hi</strong>-Di ® No.<br />
711<br />
ISO 160-016<br />
<br />
60703711
<strong>Hi</strong>-Di ® DIAMOND BURS<br />
<strong>Hi</strong>-Di ® No.<br />
563<br />
ISO 210-012<br />
<br />
60703563<br />
<strong>Hi</strong>-Di ® No.<br />
558<br />
ISO 299-018<br />
<br />
60703558<br />
T.C./Steel Round Head<br />
<strong>Hi</strong>-Di ® No.<br />
582<br />
ISO 465-016<br />
<br />
60703582<br />
<br />
60702582<br />
F.G. Barrel<br />
<strong>Hi</strong>-Di ® No.<br />
632<br />
ISO 038-034<br />
<br />
60703632<br />
Oral Surgery <strong>Burs</strong><br />
ISO Size<br />
001-006-023<br />
Pattern No.<br />
8 H.P.<br />
63613001<br />
ISO Size<br />
001-006-023<br />
Pattern No.<br />
8 R.A.<br />
63613002<br />
Steel Finishing <strong>Burs</strong> Round<br />
ISO Size<br />
001-071-016<br />
Ash ® Size I<br />
ISO Size<br />
001-071-023<br />
Ash ® Size G<br />
ISO Size<br />
171-074-016<br />
Tapered Fissure<br />
702 H.P<br />
63613003<br />
ISO Size<br />
001-071-027<br />
Ash ® Size F<br />
ISO Size<br />
171-074-016<br />
Tapered Fissure<br />
702 R.A.<br />
63613004<br />
ISO Size<br />
001-071-031<br />
Ash ® Size E<br />
Steel Finishing <strong>Burs</strong> Pear<br />
ISO Size<br />
237-071-016<br />
Ash ® Size I<br />
ISO Size<br />
237-071-019<br />
Ash ® Size H<br />
ISO Size<br />
237-071-027<br />
Ash ® Size F<br />
ISO Size<br />
237-071-031<br />
Ash ® Size E<br />
ASH ® TUNGSTEN CARBIDE AND STEEL BURS<br />
63512198<br />
63512200<br />
63512201<br />
63512203<br />
63512230<br />
63512231<br />
63512232<br />
63512233<br />
Steel Finishing <strong>Burs</strong> Flat<br />
ISO Size<br />
243-071-014<br />
ISO Size<br />
243-071-019<br />
ISO Size<br />
243-071-023<br />
ISO Size<br />
243-071-031<br />
ISO Size<br />
001-006-006<br />
ISO Size<br />
001-006-008<br />
ISO Size<br />
001-006-010<br />
ISO Size<br />
001-006-012<br />
ISO Size<br />
001-006-014<br />
ISO Size<br />
001-006-016<br />
ISO Size<br />
001-006-018<br />
ISO Size<br />
001-006-021<br />
ISO Size<br />
001-006-023<br />
ISO Size<br />
001-006-025<br />
ISO Size<br />
001-006-027<br />
Ash ® Size K<br />
63512242<br />
Ash ® Size H<br />
63512244<br />
Ash ® Size G<br />
63512245<br />
Ash ® Size E<br />
63512247<br />
Ash ® Size 1 ⁄2<br />
Ash ® Size 1<br />
Ash ® Size 2<br />
Ash ® Size 3<br />
Ash ® Size 4<br />
Ash ® Size 5<br />
Ash ® Size 6<br />
Ash ® Size 7<br />
Ash ® Size 8<br />
Ash ® Size 9<br />
Ash ® Size 10<br />
R.A. Latch TC<br />
63603000<br />
63603001<br />
63603002<br />
63603003<br />
63603004<br />
63603005<br />
63603006<br />
63603007<br />
63603008<br />
R.A. Latch Steel<br />
63503000<br />
63503001<br />
63503002<br />
63503003<br />
63503004<br />
63503005<br />
63503006<br />
63503007<br />
63503008<br />
63503009<br />
63503010<br />
HP Steel<br />
63501000<br />
63501001<br />
63501002<br />
63501003<br />
63501004<br />
63501005<br />
63501006<br />
63501007<br />
63501008<br />
63501009<br />
63501010<br />
Bur Cleaning Brush 3<br />
ASH ® TUNGSTEN CARBIDE AND STEEL BURS<br />
R.A. Latch Steel<br />
HP Steel<br />
ISO Size<br />
001-006-029<br />
Ash ® Size 11<br />
63503011<br />
63501011<br />
Steel Inverted Cone<br />
ISO Size ISO Size ISO Size<br />
001-006-031 011-006-008 011-006-010<br />
Ash ® Size 12 Ash ® Size 1<br />
63503012 63503034<br />
63501012<br />
Ash ® Size 2<br />
63503035<br />
Steel Cross Cut Flat Fissure<br />
ISO Size ISO Size ISO Size<br />
011-006-012 011-006-014 011-006-016<br />
Ash ® Size 3 Ash ® Size 4 Ash ® Size 5<br />
63503036 63503037 63503038<br />
ISO Size<br />
011-006-018<br />
Ash ® Size 6<br />
63503039<br />
ISO Size<br />
011-006-021<br />
Ash ® Size 7<br />
63503040<br />
ISO Size<br />
011-006-023<br />
Ash ® Size 8<br />
63503041<br />
ISO Size<br />
011-006-025<br />
Ash ® Size 9<br />
63503042<br />
This completely sterilisable brass wire brush is ideal for<br />
debridement of burs, pluggers and other steel instruments.<br />
The telescopic handle enables the wires to be trimmed and<br />
extended as wear occurs.<br />
Ash® Steel Bur Stand (Empty)<br />
An empty stand that holds up to 144 Ash ®<br />
Steel <strong>Burs</strong> is available.<br />
Bur Cleaning Brush 3<br />
62499050<br />
Ash ® Steel Bur Stand<br />
62515002<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
ISO Size<br />
011-006-027<br />
109-002-009<br />
109-002-010<br />
109-002-012<br />
109-002-014<br />
109-002-016<br />
109-002-018<br />
109-002-021<br />
109-002-023<br />
Ash ® Size 10<br />
Ash ® Size 1<br />
Ash ® Size 2<br />
Ash ® Size 3<br />
Ash ® Size 4<br />
Ash ® Size 5<br />
Ash ® Size 6<br />
Ash ® Size 7<br />
Ash ® Size 8<br />
R.A. Latch Steel<br />
63503043<br />
63504556<br />
63504557<br />
63504558<br />
63504559<br />
63504560<br />
63504561<br />
63504563<br />
H.P. Steel<br />
63502556<br />
63502557<br />
63502560<br />
63502561<br />
63502563<br />
63502563
Change language