Software AG's New Headquarters - the Information Technology ...

NAT1106-Data String For
"Input" Field Too Long
NOTE: May also occur as ERROR
1106.
1. Incorrect input data. Refer to
error code NAT0954, in this section,
for examples of correct
input data.
2. Refer to error code NAT7300, in
this section, to determine if it
may be applicable.
NOTE: Error occurs in module
LODNMl and is undocumented at
this time.
Refer to error code NAT0954, in
this section, to determine if it may
be applicable.
NAT7300-Dynamic Parm Error:
Parameter Not Found
NOTE: Error occurs in module
INPL and may be accompanied by
NAT1106IERROR 1106 "Data
String for 'Input' Field Too Long."
Using incorrect INPL utility.
Example:
Using NATMAINT to perform the
PREDICT INPL under NATURAL
2.
NATMAINT does not exist and is
not valid for NATURAL 2. Use
OJINPL (0s), DJINPLIXJINPL (DOS)
or INPL EXEC (CMS) from
NATURAL 2.
NAT9987-NATURAL Session
Terminated Abnormally
NOTE: Error is specific to install
under NATURAL 2 and the job will
usually show a condition code of 8.
1. Check INPL output carefully for
error codes and messages. If no
error codes or messages are
found in the output, this error
message can be ignored as long
as the INPL output shows that a
total number of modules and
sources were loaded.
2. Refer to error code NATO082 in
this section to determine if it
may be applicable.
Initialization Field
Refer to error code NATO818 in this
section to determine if it may be
applicable.
NAT9992-Storage Reouired
Exceeds 'MSIZE' Value
1. OSIDOS: Using incorrect NAT-
DEMO or batch NATURAL. For
instance, using a previous or
back-leveled NATDEMO or
batch NATURAL to run an INPL.
Use NATDEMO or batch
NATURAL for the NATURAL
SM under which the product is
being installed.
2. CMS: Using incorrect EXEC. For
instance, using a previous or
back-leveled EXEC to run an
INPL. Use EXEC for the
NATURAL SM under which the
product is being installed.
REVIEW Version 2
NAT0082-Invalid Command. Or
Object Does Not Exist In Library
Find and copy module LODSCRN
to the SYSTEM library on the
FNAT file. Rerun the INPL job.
SUPER NATURAL Version 2
This section applies to SUPER
NATURAL Version 2.1.2 and subsequent
releases.
Inactive INPL Tob
Incorrect specification of the
PROGRAM parameter on the ADA-
RUN card. PROGRAM should be
USER.
Example: ADARUN PR= USER,
MODE=MULTI,SVC=21,DA= 2
If work files which are not being
used are included in the JCLIJCS,
they should be dummied out instead
of commented out.
NAT0082-Invalid Command. Or
Object Does Not Exist In Library
Refer to error code NATO082 in the
REVIEW Version 2 section for possible
explanation of the problem.
NAT1009-Program Interrupted
After Too Many ADABAS Calls
NOTE: May also occur as ERROR
1009.
Refer to error code NAT1009 in the
NATURAL SECURITY Version 2
section for possible explanations of
the problem.
NAT1106-Data String For
"Input" Field Too Long
Specifying INPL in both the
parameter stream and the input
cards. Specify either STACK=INPL
in the parameter stream or INPL in
the input cards, not both.
NAT1311-Index In
"Move Indexed" Statement Is
Zero Or Negative
Incorrect work file allocation. Work
files should be:
CMWKFO1-Input Data Set
CMWKF02-Error Text Data Set
NAT1500-Open
File Failed
for "Work"
Incorrect specification of work file
or not using work file (CMWKFOI).
NAT1502-Permanent
I10 Error
Physical
Check for hardware errorslproblems.
Try running the INPL job on
different hardware, if possible (i.e.,
load tape on a different tape drive).
NAT3061-An Error Was Detected
In The Search Buffer
Refer to error code NAT3061 in the
NATURAL SECURITY Version 2
section for possible explanations of
the problem.
NAT9992-Storage Required
Exceeds 'MSIZE' Value
Refer to error code NAT1505 in the
NATURAL SECURITY Version 2
section for possible explanations of
the problem.
NAT9997-Not Enough Memory
To Start NATURAL
Increase the region size.