MERCEDES 307 D - 310 D - TOP DRIVE SYSTEM
MERCEDES 307 D - 310 D - TOP DRIVE SYSTEM
MERCEDES 307 D - 310 D - TOP DRIVE SYSTEM
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
4.0161-IM-VB-ENG<br />
ENG<br />
Distributed by:<br />
VB air suspension<br />
Varsseveld-Holland<br />
Frankenweg 3<br />
Varsseveld-Holland<br />
This leaflet is purely for illustrative purposes and may not reflect correctly the supplied parts. The manufacturer reserves<br />
to amend the contents of it whenever necessary and without notice.<br />
VB-Airsuspension ref.<br />
1520201001<br />
Rear integrative pneumatic suspension for<br />
<strong>MERCEDES</strong> <strong>307</strong> D - <strong>310</strong> D<br />
Until 12/1996
INSTALLATION INSTRUCTIONS<br />
PACKAGE CONTENT<br />
Ø 80 (2x)<br />
Plate (1X) Plate (1X)<br />
M10x25 (4x)<br />
Passacavo (2X)<br />
Grommet (2X)<br />
Locking plate (2X)<br />
Right suspension (1x)<br />
Left suspension (1x)<br />
SMALL HARDWARE KIT<br />
Ringnut<br />
Support<br />
plate<br />
Pressure stick (1X)<br />
Valve body<br />
<strong>TOP</strong> <strong>DRIVE</strong><br />
CONTROL<br />
cap<br />
RILSAN KIT PIPE composed<br />
by:<br />
• Red pipe (6m)<br />
• Black Pipe (6m)<br />
MANOMETERS box composed<br />
by:<br />
• Manometers with plastic<br />
ringnut (2x);<br />
• Inflating valves (2x);<br />
• Caps (for manometers) (2x).<br />
• Gauge support (1x)<br />
PRESSURE CONTROL KIT<br />
Composed by:<br />
• Valve body with pipe fittings<br />
(2x);<br />
• Caps (6x);<br />
• Support plate (2x);<br />
• Ringnut (2x).<br />
Clips kit Composed<br />
by:<br />
• Plastic clips (20x)<br />
Pneumatic system<br />
instruction (1x)<br />
RIGHT SIDE<br />
RIGHT SIDE RIGHT SIDE<br />
1<br />
2 3<br />
Place the vehicle in a hole or<br />
bridge, to operate SAFE and<br />
comfortably.<br />
Remove rebound pad and give to<br />
the end user.<br />
Place the locking plate provided<br />
inside rebound pad support.<br />
RIGHT SIDE<br />
RIGHT SIDE RIGHT SIDE<br />
4<br />
5 6<br />
Place the suspension between axle<br />
and chassis ( center holes in the<br />
locking plate ).<br />
Lock the suspension on the locking<br />
plate with provided screws..<br />
Lock the suspension on the axle<br />
with provided clamps..<br />
RIGHT SIDE<br />
7<br />
Fit RILSAN pipe on suspension pipe fitting: :<br />
• Red for right side<br />
• Black for left side.<br />
BRAKE REGULATOR MODIFICATION INSTRUCTION<br />
1<br />
2<br />
3<br />
Unscrew the side fixed to the axle of<br />
the adjustor drive rod, as showed on<br />
the picture.<br />
Place in between the holed plate and<br />
lock by mean of screws and bolts as<br />
showed in picture.<br />
Position of the drive adjustor modified<br />
correcyly.<br />
Put the work pressure stick in a place visible for the driver, in<br />
the cabin.<br />
NOTE: for the execution of pneumatic system, follow<br />
specific instructions not included in this manual. See the<br />
“pneumatic system: installation instructions” form (see<br />
picture right).<br />
WARNING : For the execution of the pneumatic system, please strictly refer the specific given instructions. In fact , the system may<br />
vary according to the chosen version (manual, self levelling or electrical); so than the instructions for the pneumatic system are stated in<br />
the apposite handbook enclosed at the purchased kit.<br />
IMPORTANT: do NOT use liquid Teflon®, hemp, paints etc. .In case of problem and/or information, contact our technical office. In case<br />
you fail to comply at this indications, societies EUROSERVICE s.r.l. and ESI Italia s.r.l. aren’t responsible for eventually damages derivates.<br />
For further information contact us.