Enviro Maxx-B - Pine Tree Stove Shoppe

Operating Instructions
AUGER
MANUAL MODE:
MODE 2
All control of 9 circuit board function is adjusted at the circuit board.
AUTO/OFF
To START: Press the ON / OFF button. The stove will turn on. The
HIGH/LOW
HIGH/LOW MODE: (Requires MODE a thermostat)
C-11625
1
AUGER
MODE
AUTO/OFF
3
HIGH/LOW
system light will flash. The Auger Light will flash with each pulse of the
MANUAL
MANUAL
auger (the Auger Feed Rate is pre-programmed during start-up). The
Heat Level Indicator will show the Heat Level
4
that the stove will run at
after start-up and can be adjusted but the change will not take affect
FEED RATE
Figure 4: Thermostat FEED Switch RATEin
until the start 8 -up HEAT has LEVEL finished. TRIM
HEAT LEVEL
MANUAL position. TRIM
If this is the first time the unit has been started or the unit has run out
5
of fuel, the auger will need to be primed. This can be done by restarting the unit five (5) minutes into its
COMBUSTION
COMBUSTION
start-up or by putting a small hand BLOWER full TRIM of pellets into the burnpot.
BLOWER TRIM
To OPERATE: When a fire has been established, the System Light will turn solid (after approximately 10
7
6
- 15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting.
ROOM AIR
ON/OFF
ROOM AIR
ON/OFF
The convection blower FAN ON/OFF (room air blower) will turn on. The speed of this blower FAN is ON/OFF controlled by the setting
of the heat level output indicator. The convection blower can be turned OFF by depressing the convection
blower control button. For the best AUGERefficiency the 1 convection blower should be left on at all AUGER times.
2
9
INITIAL START-UP: See manual mode above.
AUTO/OFF
OPERATION: When the thermostat calls for heat (contacts are closed)
HIGH/LOW 3
the stove settings are adjustable MANUALas per Manual Mode. When the
thermostat contacts open, the HEAT LEVEL and Fans will drop down to
the LOW setting until the thermostat contacts 4close again. *The LOW
heat setting can be adjusted for different FEED RATE fuel qualities (see “Operating
8 HEAT LEVEL
AUGER 1
Instructions - Control Board Functions”). TRIM The stove will come back to
the previous HEAT LEVEL setting when the thermostat 5 contacts close
MODE 2
again. 9
COMBUSTION
AUTO/OFF BLOWER TRIM
AUTO/OFF
HIGH/LOW
C-11625
Figure 5: Thermostat FEED Switch RATEin
HEAT LEVEL
AUGER
HIGH/LOW position. TRIM
COMBUSTION
AUTO/OFF BLOWER TRIM
AUTO/OFF MODE: (Requires HIGH/LOW a thermostat) 3
HIGH/LOW
INITIAL START-UP:
7
6
See manual
MANUAL
mode above.
MANUAL
ROOM AIR
ON/OFF
ROOM AIR
ON/OFF
OPERATION: When
FAN ON/OFF
the thermostat contacts close, the unit will light
FAN ON/OFF
automatically. Once up to temperature, the stove
4
operates the same
Figure 6: Thermostat Switch in
as in MANUAL. When the thermostat
FEED RATE
contacts open, the stove’s HEAT
FEED RATE
8 HEAT LEVEL
TRIM
HEAT LEVEL ON/OFF position. TRIM
LEVEL and Fans will drop down to the LOW setting for 30 minutes. If
the thermostat contacts close within the C-11625 30 minutes, 5 the HEAT LEVEL will return to the previous MANUAL
C-11625
setting. If the thermostat contacts COMBUSTION remain open the stove automatically begins its shutdown routine. COMBUSTION The
BLOWER TRIM
BLOWER TRIM
ON / OFF button can be presses at any time the the stove will immediately shut down. The stove will relight
when 7the thermostat contacts close again. 6
ROOM AIR
ON/OFF
Turning Your Pellet FAN ON/OFFStove Off:
ROOM AIR
FAN ON/OFF
• MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop
the feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough,
C-11625
C-11625
the stove will turn off.
• AUTO / OFF mode: To turn the unit OFF, turn the thermostat down or off. NOTE: The unit will run on
low for three (3) minutes before it turns off.
DO NOT unplug unit while Combustion fan is operating.
This may lead to smoke escaping from the stove.
MODE
MANUAL
MODE
ON/OFF
8